| 1. |
- Almqvist, Torbjörn, et al.
(författare)
-
A comparison between computational fluid dynamic and Reynolds approaches for simulating transient EHL line contacts
- 2004
-
Ingår i: Tribology International. - Pergamon. - 0301-679X. ; 37:1
-
Tidskriftsartikel (övrigt vetenskapligt)abstract
- When simulating elastohydrodynamic lubrication (EHL), the Reynolds equation is the predominating partial differential equation for prediction of the fluid flow. Also very few attempts have been carried out using the full momentum and continuity equations separately. The aim of this investigation is to compare two different approaches for simulation of EHL line contacts where a single ridge travels through an EHL conjunction. One of the approaches is based on the Reynolds equation, addressing the coupling between the pressure and the film thickness. The solver uses the advantages of multilevel techniques to speed up the convergence rate. The other approach is based on commercial CFD software. The software uses the momentum and continuity equations in their basic form, enabling numerical simulations outside the contact regions, as well as in the thin film region to be carried out. The numerical experiments show that, under the running conditions chosen, only small deviations between the two approaches can be observed. The results are encouraging from several viewpoints: validation of the codes, the possibilities of further developments of the CFD approach and the justification of using a Reynolds approach under the running conditions chosen
|
|
| 2. |
- Aberg, V., et al.
(författare)
-
Synthesis and absolute configuration of methyl(-)-(3R)-8-(4-bromophenyl)-7-(naphthalen-1-yl-methyl)-5-oxo-2,3-dihydro-5H-thiazolo 3,2-a pyridine-3-carboxylate
- 2002
-
Ingår i: Acta Crystallographica Section E : Structure Reports Online. - 1600-5368. ; 58, s. o812-o814
-
Tidskriftsartikel (refereegranskat)abstract
- The title molecule, C26H20BrNO3S, contains a ring-fused 2-pyridinone framework substituted with a 4-bromo-phenyl-, a naphthalen-1-ylmethyl and a methoxycarbonyl substituent. The main goal of this work was to confirm the stereochemistry for the methoxycarbonyl substituent, which proved to be 3R. Moreover, the 4-bromophenyl substituent was shown to be rotated out of the plane of the 2-pyridinone ring, with a torsion angle of 61.2 (5)degrees. To allow the best packing arrangement, the naphthalen-1-ylmethyl substituent is positioned to mediate an intermolecular pi-pi interaction.
|
|
| 3. |
- Almqvist, Andreas, et al.
(författare)
-
On the dry elasto-plastic contact of nominally flat surfaces
- 2007
-
Ingår i: Tribology International. - Pergamon. - 0301-679X. ; 40:4
-
Tidskriftsartikel (övrigt vetenskapligt)abstract
- A model to be used for numerical simulation of the contact of linear elastic perfectly plastic rough surfaces was developed. Energy dissipation due to plastic deformation is taken into account. Spectral theory and an FFT-techique are used to facilitate the numerical solution process. Results of simulations using four two-dimensional profiles with different topographies in contact with a rigid plane for a number loads are reported. From the results it is clear that the real area of contact (Ar) changes almost linearly with load and is only slightly affected by the difference in topography. A plasticity index is defined as the ratio of plastically deformed area (Ap) and Ar. Plastic deformation occurs even at low loads and there is a significant difference in plasticity index between the surface profiles considered. An investigation on how the spectral content of the surface profile influences the results presented is also performed. This is to ensure that the metrological limitations of the optical profilerused to measure the surfaces do not have a significant influence. It is concluded that the highest frequencies of the measured profile have a negligible influence on the real area of contact.
|
|
| 4. |
- Almqvist, Andreas
(författare)
-
On the effects of surface roughness in lubrication
- 2006
-
Doktorsavhandling (övrigt vetenskapligt)abstract
- Tribology is a multidisciplinary field defined as the science and technology of interacting surfaces in relative motion, and embraces the study of friction, wear and lubrication. A typical tribological application is the rolling element bearing. Tribological contacts may also be found in other types of bearings, cam-mechanisms, gearboxes and hydraulic systems. Examples of bearings inside the human body are the operation of the human hip joint and the contact between teeth during chewing. To fully understand the operation of this type of application one has to understand the couplings between the lubricant fluid dynamics, the structural dynamics of the bearing material, the thermodynamical aspects and the resulting chemical reactions. This makes modeling tribological applications an extremely delicate task. Because of the multidisciplinary nature, such theoretical models lead to mathematical descriptions generally in the form of non-linear integro-differential systems of equations. Some of these systems of equations are sufficiently well posed to allow numerical solutions to be carried out, resulting in accurate predictions on performance. In this work, the influence on performance of a surface microscopical nature, the surface roughness, in contact interfaces between different types of machine element components is the subject of study. An example is the non-conformal lubricated contact between one of the rollers and the inner ring in a rolling element bearing. The tribological contact controlling the operation of the human hip joint is also very similar to this. Another example of a non-conformal contact occurs when driving on rainy roads, where the hydrodynamic action of the water separates the tire. To enable investigations of these types of problems, different theoretical models were studied; for the selected model, a numerical solution technique was developed within this project. This model is based on the Reynolds equation coupled with the film thickness equation. The numerical solution technique involves amultilevel technique to facilitate the solution process. Results presented in this thesis, utilizing this approach, study elementary surface features such as ridges and indentations passing each other inside the lubricated conjunction. The Reynolds equation is derived under the assumptions of thin fluid film and creeping flow, and considers in its most general form shear thinning of the lubricant. This type of equation describes the hydrodynamic action of the lubricant flow and may be used when the interfaces consist of either conformal or non-conformal conjunctions. Examples of applications having conformal interfaces are thrust- and journal- bearings or the contact between the eye and a (optical) contact lens. In such types of applications the load carried by the interface is distributed over a fairly large area that under certain circumstances helps to prevent mechanical deformation of the contacting surfaces. Such applications are said to operate in the hydrodynamic lubrication (HL) regime. Lubricant compressibility and cavitation are important aspects and have received some attention. However, the main objective when modeling HL has been to investigate and develop methods that enable the influence of surface roughness to be to be studied efficiently. Homogenization is a rigorous mathematical concept that when applied to a certain problem may be regarded as an averaging technique as well as it provides information about the induced effects of local surface roughness. Homogenization inflicts no restrictions on the surface roughness representation other than the representative part of the chosen surface roughness being assumed periodically distributed and of course the assumptions of thin film flow made through the Reynolds equation. The homogenization process leads to a two sets of equations one for the local scale describing surface roughness, scale and one for the global scale describing application geometry. The unequivocally determined coefficients of the global problem, which may be regarded as flow factors, are obtained through the solution of local problems. This makes homogenization an eminent approach to be used investigating the influence of surface roughness on hydrodynamic performance. In the present work, homogenization has been used to derive computationally feasible forms of problems originating from incompressible and compressible Reynolds type equations that describe stationary and unstationary flows in both cartezian and cylindrical co-ordinates. This technique enables simulations of surface roughness induced effects when considering surface roughness descriptions originating from measurements. Moreover, the application of homogenization facilitates the interpretation of results. Numerical investigations following the homogenization process have been carried out to verify the applicability of homogenization in hydrodynamic lubrication. Homogenization has also been shown here to enable efficient analysis of rough hydrodynamically lubricated problems. Also of note, in connection to the scientific contribution within tribology, collaboration with a group in applied mathematics has lead to the development of novel techniques in that area. These ideas have also been successfully applied, with some results presented in this thesis. At start-ups, the contact in a rolling element bearing could be both starved and drained from lubricant. In this case the hydrodynamic action becomes negligible in terms of load carrying capacity. The load is carried exclusively by surface asperities, the tribo film, or both. This is hereby modeled as the unlubricated frictionless contact between rough surfaces, i.e. a contact mechanical approach. A variational principle was used in which the real area of contact and the contact pressure distribution minimize the total complementary potential energy. The material model is linear elastic-perfectly plastic and the energy dissipation due to plastic deformation is accounted for. The numerics of this contact mechanical approach involve the fast Fourier transformation (FFT) techniquein order to facilitate the solution process. Investigation results of the contact mechanics of realistic surfaces are presented in this thesis. In this investigation the variation in the real area of contact, the plasticity index and some surface roughness parameters due to applied load were studied.
|
|
| 5. |
- Almqvist, Andreas
(författare)
-
Rough surface elastohydrodynamic lubrication and contact mechanics
- 2004
-
Licentiatavhandling (övrigt vetenskapligt)abstract
- In the field of tribology, there are numerous theoretical models that may be described mathematically in the form of integro-differential systems of equations. Some of these systems of equations are sufficiently well posed to allow for numerical solutions to be carried out resulting in accurate predictions. This work has focused on the contact between rough surfaces with or without a separating lubricant film. The objective was to investigate how surface topography influences contact conditions. For this purpose two different numerical methods were developed and used. For the lubricated contact between rough surfaces the Reynolds equation were used as a basis. This equation is derived under the assumptions of thin fluid film and creeping flow. In highly loaded, lubricated, non- conformal contacts of surfaces after running-in, the load concentration no longer results in plastic deformations, however large elastic deformations will be apparent. It is the interaction between the hydrodynamic action of the lubricant and the elastic deformations of the surfaces that, in certain applications, enable the lubricant film to fully separate the surfaces. This is commonly referred to as full film elastohydrodynamic (EHD) lubrication. Typical machine elements that operates in the full film EHD lubrication (FL) regime include rolling element bearings, cams and gears. Unfortunately, a cost effective way of machining engineering surfaces seldom results in a surface topography that influence contact conditions in the same way as a surface after running-in. Such topographies may prevent the lubricant from fully separating the surfaces because of deteriorated hydrodynamic action. In this case the applied load is carried in part by the lubricant and in part by surface asperities and/or surface active lubricant additives. This could also be the case in lubricant starved contacts, which is a common situation in not only grease lubricated contacts but also in many liquid lubricated contacts, such as high speed operating rolling element bearings. The load sharing between the highly compressed lubricant and the surface and/or surface active lubricant additives is the reason why this lubrication regime is most commonly referred to as mixed EHD lubrication (ML). Machine elements that while running operate in the FL regime may experience a transition into the ML regime at stops or due to altered operating conditions. It is not possible to simulate direct contact between the surfaces using a numerical method based on Reynolds equation. A parameter study, of elementary surface features passing each other inside the EHD lubricated conjunction, was performed. The results obtained, even though no direct contact could be simulated, does indicate that a transition from the FL to the ML regime would occur for certain combinations of the varied parameters. At start-ups, the contact in a rolling element bearing could be both starved and drained from lubricant. In this case the hydrodynamic action becomes negligible in terms of load carrying capacity. The load is carried exclusively by surface asperities and/or surface active lubricant additives. This regime is referred to as boundary lubrication (BL). Operation conditions could also make both FL and ML impossible to achieve, for example, in the case in a low rpm operating rolling element bearing. The BL regime is in this work modeled as the unlubricated frictionless contact between rough surfaces, i.e., a dry contact approach. A variational principle was used in which the real area of contact and contact pressure distribution are those which minimize the total complementary energy. A linear elastic-perfectly plastic deformation model in which energy dissipation due to plastic deformation is accounted for was used. The dry contact method was applied to the contact between four different profiles and a plane. The variation in the real area of contact, the plasticity index and some surface roughness parameters due to applied load were investigated. The surface roughness parameters of the profiles differed significantly.
|
|
| 6. |
- Almqvist, Andreas, et al.
(författare)
-
The effect of two-sided roughness in rolling/sliding EHL line contacts
- 2004
-
Ingår i: Transient processes in tribology : proceedings of the 30th Leeds-Lyon Symposium on Tribology. - Amstersam : Elsevier. - 0-444-51706-5
-
Annan publikation (populärvet., debatt m.m.)abstract
- In most theoretical studies carried out to date on the effect of surface roughness in elastohydrodynamic lubrication (EHL) one surface is considered smooth and one as being rough. In real tribological contacts however, both surfaces normally have similar roughness heights. When modelling a rolling contact it is possible to simply sum the roughness of the two contact surfaces but in a sliding EHL contact, a continuously changing effective surface roughness occurs. The aim of this work was to investigate the influence of elementary surface features such as dents and ridges on the film thickness and pressure. This was done numerically using transient non-Newtonian simulations of an EHL line contact using a coupled smoother combined with a multilevel technique. Four different "overtaking" phenomena were investigated; ridge-ridge, dent-ridge, ridge-dent, and dent-dent. It was shown that the minimum film-thickness produced by a ridge is further reduced in a dent-ridge overtaking event. The squeeze effect seen in the ridge-ridge case resulted in large deformations and film-thickness heights comparable to the corresponding smooth case just before the overtaking event occurred. These local effects arising from simulating two-sided roughness were compared to simulations using a traditional "one-sided rough surface contacting a perfectly smooth surface.".
|
|
| 7. |
- Almqvist, Andreas, et al.
(författare)
-
The homogenization process of the Reynolds equation describing compressible liquid flow
- 2006
-
Ingår i: Tribology International. - Pergamon. - 0301-679X. ; 39:9
-
Tidskriftsartikel (övrigt vetenskapligt)abstract
- This paper summarizes the homogenization process of rough, hydrodynamic lubrication problems governed by the Reynolds equation used to describe compressible liquid flow. Here, the homogenized equation describes the limiting result when the wavelength of a modeled surface roughness goes to zero. The lubricant film thickness is modeled by one part describing the geometry/shape of the bearing and a periodic part describing the surface topography/roughness. By varying the periodic part as well as its wavelength, we can try to systematically investigate the applicability of homogenization on this type of problem. The load carrying capacity is the target parameter; deterministic solutions are compared to homogenized by this measure. We show that the load carrying capacity rapidly converges to the homogenized results as the wavelength decreases, proving that the homogenized solution gives a very accurate representation of the problem when real surface topographies are considered
|
|
| 8. |
- Almqvist, Roland, et al.
(författare)
-
Management Control of Health : - the Swedish examples
- 2007
-
Ingår i: Work Health and Management Control. - Stockholm : Thomson Fakta. - 978-91-7610-272-5 ; s. 291-318
-
Bokkapitel (övrigt vetenskapligt)abstract
- Management control practices have spread to areas other than formerly occupied by traditional management accounting techniques. In this chapter, results from a number of development projects regarding management control of health are presented. The purpose of the chapter is to assess the proposed health statement models in Sweden as leading or lagging management control systems: (1) How are health statements used in the organizations? (2) Could health statements be an effective device to develop management control practices with the aim of improving health? The research has been performed through longitudinal studies including in-depth interviews and observations made over a three-year period. The empirical findings are analyzed using a two-dimensional matrix comprising diagnostic reporting routines and interactive management control functions. Tentative conclusions indicate that the proposed health statement models are mainly based on diagnostic control with a focus on lagging indicators, but there are examples of the successful integration of health statement models with management control models when certain criteria of change are fulfilled.
|
|
| 9. |
|
|
| 10. |
|
|
