| 1. |
- Nilsson, Viktor, 1985-
(författare)
-
Highly Concentrated Electrolytes for Lithium Batteries : From fundamentals to cell tests
- 2018
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The electrolyte is a crucial part of any lithium battery, strongly affecting longevity and safety. It has to survive rather severe conditions, not the least at the electrode/electrolyte interfaces. Current commercial electrolytes based on 1 M LiPF 6 in a mixture of organic solvents balance the requirements on conductivity and electrochemical stability, but they are volatile and degrade when operated at temperatures above ca. 70°C. The salt could potentially be replaced with e.g. LiTFSI, but corrosion of the aluminium current collector is an issue. Replacing the graphite negative electrode by Li metal for large gains in energy density challenges the electrolyte further by exposing it to freshly deposited Li, leading to poor coulombic efficiency (CE) and consumption of both Li and electrolyte. Highly concentrated electrolytes (up to > 4 M) have emerged as a possible remedy, by a changed solvation structure such that all solvent molecules are coordinated to cations – leading to a lowered volatility and melting point, an increased charge carrier density and electrochemical stability, but a higher viscosity and a lower ionic conductivity.Here two approaches to highly concentrated electrolytes are evaluated. First, LiTFSI and acetonitrile electrolytes with respect to increased electrochemical stability and in particular the passivating solid electrolyte interphase (SEI) on the anode is studied using electrochemical techniques and X-ray photoelectron spectroscopy. Second, lowering the liquidus temperature by high salt concentration is utilized to create an electrolyte solely of LiTFSI and ethylene carbonate, tested for application in Li metal batteries by characterizing the morphology of plated Li using scanning electron microscopy and the CE by galvanostatic polarization. While the first approach shows dramatic improvements, the inherent weaknesses cannot be completely avoided, the second approach provides some promising cycling results for Li metal based cells. This points towards further investigations of the SEI, and possibly long-term safe cycling of Li metal anodes.
|
|
| 2. |
- Aktekin, Burak, et al.
(författare)
-
Cation Ordering and Oxygen Release in LiNi0.5-xMn1.5+xO4-y (LNMO)—In Situ Neutron Diffraction and Performance in Li-Ion Full Cells
- 2018
-
Konferensbidrag (refereegranskat)abstract
- LiNi0.5Mn1.5O4 (LNMO) is a promising spinel-type positive electrode for lithium ion batteries as it operates at high voltage and possesses high power capability. However, rapid performance degradation in full cells, especially at elevated temperatures, is a problem. There has been a considerable interest in its crystal structure as this is known to affect its electrochemical performance. LNMO can adopt a P4332 (cation ordered) or Fd-3m (cation disordered) arrangement depending on the synthesis conditions. Most of the studies in literature agree on better electrochemical performance for disordered LNMO [1], however, a clear understanding of the reason for this behaviour is still lacking. This partly arises from the fact that synthesis conditions leading to disordering also lead to oxygen deficiency, rock-salt impurities and therefore generate some Mn3+ [2]. Most commonly, X-ray diffraction is used to characterize these materials, however, accurate structural analysis is difficult due to the near identical scattering lengths of Mn and Ni. This is not the case for neutron diffraction. In this study, an in-situ neutron diffraction heating-cooling experiment was conducted on slightly Mn-rich LNMO under pure oxygen atmosphere in order to investigate relationship between disordering and oxygen deficiency. The study shows for the first time that there is no direct relationship between oxygen loss and cation disordering, as disordering starts prior to oxygen release. Our findings suggest that it is possible to obtain samples with varying degrees of ordering, yet with the same oxygen content and free from impurities. In the second part of the study, highly ordered, partially ordered and fully disordered samples have been tested in LNMO∥LTO (Li4Ti5O12) full cells at 55 °C. It is shown that differences in their performances arise only after repeated cycling, while all the samples behave similarly at the beginning of the test. The difference is believed to be related to instabilities of LNMO at higher voltages, that is, in its lower lithiation states.[1] A. Manthiram, K. Chemelewski, E.-S. Lee, Energy Environ. Sci. 7 (2014) 1339.[2] M. Kunduraci, G.G. Amatucci, J. Power Sources. 165 (2007) 359–367.
|
|
| 3. |
- Aktekin, Burak, et al.
(författare)
-
Understanding the Capacity Loss in LiNi0.5Mn1.5O4-Li4Ti5O12 Lithium-Ion Cells at Ambient and Elevated Temperatures
- 2018
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 122:21, s. 11234-11248
-
Tidskriftsartikel (refereegranskat)abstract
- The high-voltage spinel LiNi0.5Mn1.5O4, (LNMO) is an attractive positive electrode because of its operating voltage around 4.7 V (vs Li/Li+) and high power capability. However, problems including electrolyte decomposition at high voltage and transition metal dissolution, especially at elevated temperatures, have limited its potential use in practical full cells. In this paper, a fundamental study for LNMO parallel to Li4Ti5O12 (LTO) full cells has been performed to understand the effect of different capacity fading mechanisms contributing to overall cell failure. Electrochemical characterization of cells in different configurations (regular full cells, back-to-back pseudo-full cells, and 3-electrode full cells) combined with an intermittent current interruption technique have been performed. Capacity fade in the full cell configuration was mainly due to progressively limited lithiation of electrodes caused by a more severe degree of parasitic reactions at the LTO electrode, while the contributions from active mass loss from LNMO or increases in internal cell resistance were minor. A comparison of cell formats constructed with and without the possibility of cross-talk indicates that the parasitic reactions on LTO occur because of the transfer of reaction products from the LNMO side. The efficiency of LTO is more sensitive to temperature, causing a dramatic increase in the fading rate at 55 degrees C. These observations show how important the electrode interactions (cross-talk) can be for the overall cell behavior. Additionally, internal resistance measurements showed that the positive electrode was mainly responsible for the increase of resistance over cycling, especially at 55 degrees C. Surface characterization showed that LNMO surface layers were relatively thin when compared with the solid electrolyte interphase (SEI) on LTO. The SEI on LTO does not contribute significantly to overall internal resistance even though these films are relatively thick. X-ray absorption near-edge spectroscopy measurements showed that the Mn and Ni observed on the anode were not in the metallic state; the presence of elemental metals in the SEI is therefore not implicated in the observed fading mechanism through a simple reduction process of migrated metal cations.
|
|
| 4. |
- Björklund, Erik, et al.
(författare)
-
Influence of state-of-charge in commercial LiNi0.33Mn0.33Co0.33O2/LiMn2O4-graphite cells analyzed by synchrotron-based photoelectron spectroscopy
- 2018
-
Ingår i: Journal of Energy Storage. - : Elsevier BV. - 2352-152X .- 2352-1538. ; 15, s. 172-180
-
Tidskriftsartikel (refereegranskat)abstract
- Degradation mechanisms in 26 Ah commercial Li-ion battery cells comprising graphite as the negative electrode and mixed metal oxide of LiMn 2 O 4 (LMO) and LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC) as the positive electrode are here investigated utilising extensive cycling at two different state-of-charge (SOC) ranges, 10–20% and 60–70%, as well as post-mortem analysis. To better analyze these mechanisms electrochemically, the cells were after long-term cycling reassembled into laboratory scale “half-cells” using lithium metal as the negative electrode, and thereafter cycled at different rates corresponding to 0.025 mA/cm 2 and 0.754 mA/cm 2 . The electrodes were also analyzed by synchrotron-based hard x-ray photoelectron spectroscopy (HAXPES) using two different excitation energies to determine the chemical composition of the interfacial layers formed at different depth on the respective electrodes. It was found from the extensive cycling that the cycle life was shorter for the cell cycled in the higher SOC range, 60–70%, which is correlated to findings of an increased cell resistance and thickness of the SEI layer in the graphite electrode as well as manganese dissolution from the positive electrode.
|
|
| 5. |
- Doubaji, Siham, et al.
(författare)
-
On the P2-NaxCo1−y(Mn2/3Ni1/3)yO2 Cathode Materials for Sodium-Ion Batteries : Synthesis, Electrochemical Performance, and Redox Processes Occurring during the Electrochemical Cycling
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 10:1, s. 488-501
-
Tidskriftsartikel (refereegranskat)abstract
- P2-type NaMO2sodiated layered oxides withmixed transition metals are receiving considerable attention foruse as cathodes in sodium-ion batteries. A study on solidsolution (1−y)P2-NaxCoO2−(y)P2-NaxMn2/3Ni1/3O2(y=0,1/3, 1/2, 2/3, 1) reveals that changing the composition of thetransition metals affects the resulting structure and the stabilityof pure P2 phases at various temperatures of calcination. For 0≤y≤1.0, the P2-NaxCo(1−y)Mn2y/3Niy/3O2solid-solutioncompounds deliver good electrochemical performance whencycled between 2.0 and 4.2 V versus Na+/Na with improved capacity stability in long-term cycling, especially for electrodematerials with lower Co content (y= 1/2 and 2/3), despite lower discharge capacities being observed. The (1/2)P2-NaxCoO2−(1/2)P2-NaxMn2/3Ni1/3O2composition delivers a discharge capacity of 101.04 mAh g−1with a capacity loss of only 3% after 100cycles and a Coulombic efficiency exceeding 99.2%. Cycling this material to a higher cutoffvoltage of 4.5 V versus Na+/Naincreases the specific discharge capacity to≈140 mAh g−1due to the appearance of a well-defined high-voltage plateau, but afteronly 20 cycles, capacity retention declines to 88% and Coulombic efficiency drops to around 97%. In situ X-ray absorption near-edge structure measurements conducted on composition NaxCo1/2Mn1/3Ni1/6O2(y= 1/2) in the two potential windows studiedhelp elucidate the operating potential of each transition metal redox couple. It also reveals that at the high-voltage plateau, all ofthe transition metals are stable, raising the suspicion of possible contribution of oxygen ions in the high-voltage plateau.
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Etman, Ahmed, et al.
(författare)
-
One-pot Synthesis of MoO3-x Nanosheets for Supercapacitor Applications
- 2018
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Molybdenum oxide nanosheets are interesting materials for energy storage, catalysis, and gas sensor applications.1 However, they are traditionally prepared via a variety of approaches which require the use of high temperature or organic solvents.2,3 Herein, we report the synthesis of MoO3-x nanosheets (where x denotes oxygen vacancy) via a one-step water based exfoliation strategy using bulk molybdenum oxides precursors.4 Scanning and transmission electron microscopy show that the MoO3-x has a typical nanosheet morphology with a few nanometer thickness. The MoO3-x nanosheets display localized surface plasmon resonance (LSPR), which can be enhanced by modifying the morphology and the amount of oxygen vacancies (x) using chemical and/or photochemical treatments.The aqueous suspension of the MoO3-x nanosheets was drop-cast onto carbon paper and this material was then used as binder free electrodes for supercapacitor applications. The electrodes showed promising performance regarding capacitance and rate capability in acidified sodium sulphate solutions. The facile green synthesis of MoO3-x nanosheets coupled with their significant photochemical and electrochemical properties pave the way for the use of the nanosheets in a variety of applications.References:(1) de Castro, I. A.; Datta, R. S.; Ou, J. Z.; Castellanos-Gomez, A.; Sriram, S.; Daeneke, T.; Kalantar-zadeh, K. Molybdenum Oxides - From Fundamentals to Functionality. Adv. Mater. 2017, 29 (40), 1701619.(2) Xiao, X.; Song, H.; Lin, S.; Zhou, Y.; Zhan, X.; Hu, Z.; Zhang, Q.; Sun, J.; Yang, B.; Li, T.; Jiao, L.; Zhou, J.; Tang, J.; Gogotsi, Y. Scalable Salt-Templated Synthesis of Two-Dimensional Transition Metal Oxides. Nat. Commun. 2016, 7, 11296.(3) Alsaif, M. M. Y. A.; Field, M. R.; Daeneke, T.; Chrimes, A. F.; Zhang, W.; Carey, B. J.; Berean, K. J.; Walia, S.; van Embden, J.; Zhang, B.; Latham, K.; Kalantar-zadeh, K.; Ou, J. Z. Exfoliation Solvent Dependent Plasmon Resonances in Two-Dimensional Sub-Stoichiometric Molybdenum Oxide Nanoflakes. ACS Appl. Mater. Interfaces 2016, 8 (5), 3482–3493.(4) Etman A. S.; Abdelhamid H. N.; Yuan Y.; Wang L.; Zou X.; Sun J. Facile Water Based Strategy for Synthesizing MoO3-x Nanosheets: Efficient Visible Light Photocatalyst for Dye Degradation. ACS Omega. in Press.
|
|
| 9. |
- Farhat, Douaa, et al.
(författare)
-
Towards high-voltage Li-ion batteries : Reversible cycling of graphite anodes and Li-ion batteries in adiponitrile-based electrolytes
- 2018
-
Ingår i: Electrochimica Acta. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0013-4686 .- 1873-3859. ; 281, s. 299-311
-
Tidskriftsartikel (refereegranskat)abstract
- Due to their low vapor pressure and their promising electrochemical and thermal stability, N C- (CH2)n-C N dinitriles are proposed as an electrolyte solvent for Li-ion batteries. Adiponitrile (ADN) has substantial advantages, especially for applications requiring high potential cathodes, because it has high electrochemical/thermal stability (up to 6 V vs. Li/Li+, > 120 degrees C). However, to obtain very high voltage batteries, ADN electrolytes must also passivate the anode of the battery. In this work, reversible cycling of graphite in adiponitrile was successfully achieved by adding a few percent of fluoroethylene carbonate allowing the realization of Graphite/NMC Li-ion battery. The battery of specific capacity of 135 mAhh.g(-1) showed a cycling stability for more than 40 cycles. The composition of the solid electrolyte interphase (SEI) was determined as a function of the FEC concentration as well as the state of charge of the graphite anode using hard X-ray photoelectron spectroscopy (HAXPES) and XPS. With FEC, the SEI layer is thinner and depends on the SOC of the anode, but does not depend on the FEC concentration. SEM characterizations clearly showed that the surface of the anode is completely covered by the SEI layer, regardless of the concentration of FEC. Indeed, 2% of FEC is sufficient to suppress the reduction of adiponitrile which is explained by a specific adsorption of FEC on the graphite anode.
|
|
| 10. |
- Hernández, Guiomar, et al.
(författare)
-
Non-Fluorinated Electrolytes for Si-based Li-ion Battery Anodes
- 2018
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Although the performance of lithium-ion batteries has been improved to some extent since the initial commercialization,1 cycling stability, safety and sustainability still present some challenges and concerns. In this regard, the battery electrolyte plays an important role. State-of-the-art electrolytes contain the electrolyte salt LiPF6, susceptible to undergo defluorination reactions and form toxic and corrosive compounds, such as HF. Yet, fluorine-containing electrolytes are often considered necessary for enhanced battery performance. On the other hand, replacing LiPF6 with fluorine-free salts would reduce cost, increase safety and decrease toxicity, both in the manufacturing and recycling processes. Among the available fluorine-free salts, lithium bis(oxalato)borate (LiBOB) is a viable candidate due to its enhanced thermal stability.2 Furthermore, additives in the electrolyte are another common source of fluorine, not least fluoroethylene carbonate (FEC) which can form a stable solid electrolyte interface (SEI).3Herein, we compare the cell performance of fluorinated and non-fluorinated electrolytes in NMC/Si-Graphite full cells. Three electrolytes are tested: (1) LP57 (1 M LiPF6 in ethylene carbonate (EC):ethyl methyl carbonate (EMC) 3:7 vol/vol); (2) LP57 with 10 wt% FEC and 2 wt% vinylene carbonate (VC); and (3) 0.7 M LiBOB in EC:EMC 3:7 vol/vol and 2 wt% VC.The cells containing the conventional electrolyte, LP57, feature a rapid capacity fade and continuous decrease in coulombic efficiency. The cell performance is improved when adding SEI-forming additives to the electrolyte (LP57 with FEC and VC). In addition, stable cycling for over 200 cycles are obtained for both the fluorinated (LP57 with FEC and VC) and non-fluorinated (LiBOB with VC) electrolytes.Characterisation by X-ray photoelectron spectroscopy (XPS) of the anode surface showed higher amounts of carbonate species and a thicker SEI layer with the non-fluorinated electrolyte compared to the fluorinated one.1 J. Electrochem. Soc. 2017, 164, A5019-A5025.2 ChemSusChem 2017, 10, 2431-2448.3 J. Electrochem. Soc. 2014, 161, A1933-A1938.
|
|
