| 1. |
- Chi, Xiaoming, et al.
(författare)
-
Fractal superconducting nanowire single-photon detectors with reduced polarization sensitivity
- 2018
-
Ingår i: Optics Letters. - : OPTICAL SOC AMER. - 0146-9592 .- 1539-4794. ; 43:20, s. 5017-5020
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate superconducting nanowire single-photon detectors (SNSPDs) based on a fractal design of the nanowires to reduce the polarization sensitivity of detection efficiency. We patterned niobium titanium nitride thin films into Peano curves with a linewidth of 100 nm and integrated the nanowires with optical microcavities to enhance their optical absorption. At a base temperature of 2.6 K, the fractal SNSPD exhibited a polarization-maximum device efficiency of 67% and a polarization-minimum device efficiency of 61% at a wavelength of 1550 nm. Therefore, the polarization sensitivity, defined as their ratio, was 1.1, lower than the polarization sensitivity of the SNSPDs in the meander design. The reduced polarization sensitivity of the detector could be maintained for higher-order spatial modes in multimode optical fibers and could tolerate misalignment between the optical mode and the detector. This fractal design is applicable to both amorphous and polycrystalline materials that are commonly used for making SNSPDs.
|
|
| 2. |
|
|
| 3. |
- Chen, Gang, et al.
(författare)
-
EDF-VD Scheduling of Flexible Mixed-Criticality System With Multiple-Shot Transitions
- 2018
-
Ingår i: IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems. - 0278-0070 .- 1937-4151. ; 37:11, s. 2393-2403
-
Tidskriftsartikel (refereegranskat)abstract
- The existing mixed-criticality (MC) real-time task models assume that once any high-criticality task overruns, all high-criticality jobs execute up to their most pessimistic WCET estimations simultaneously in a one-shot manner. This is very pessimistic in the sense of unnecessary resource overbooking. In this paper, we propose a more generalized mixed-critical real-time task model, called flexible MC model with multiple-shot transitions (FMC-MST), to address this problem. In FMC-MST, high-criticality tasks can transit multiple intermediate levels to handle less pessimistic overruns independently and to nonuni-formly scale the deadline on each level. We develop a run-time schedulability analysis for FMC-MST under EDF-VD scheduling, in which a better tradeoff between the penalties of low-criticality tasks and the overruns of high-criticality tasks is achieved to improve the service quality of low-criticality tasks. We also develop a resource optimization technique to find resource-efficient level-insertion configurations for FMC-MST task systems under MC timing constraints. Experiments demonstrate the effectiveness of FMC-MST compared with the state-of-the-art techniques.
|
|
| 4. |
- Wang, Nan, 1988, et al.
(författare)
-
Tailoring the Thermal and Mechanical Properties of Graphene Film by Structural Engineering
- 2018
-
Ingår i: Small. - : Wiley. - 1613-6810 .- 1613-6829. ; 14:29
-
Tidskriftsartikel (refereegranskat)abstract
- Due to substantial phonon scattering induced by various structural defects, the in-plane thermal conductivity (K) of graphene films (GFs) is still inferior to the commercial pyrolytic graphite sheet (PGS). Here, the problem is solved by engineering the structures of GFs in the aspects of grain size, film alignment, and thickness, and interlayer binding energy. The maximum K of GFs reaches to 3200 W m−1K−1and outperforms PGS by 60%. The superior K of GFs is strongly related to its large and intact grains, which are over four times larger than the best PGS. The large smooth features about 11 µm and good layer alignment of GFs also benefit on reducing phonon scattering induced by wrinkles/defects. In addition, the presence of substantial turbostratic-stacking graphene is found up to 37% in thin GFs. The lacking of order in turbostratic-stacking graphene leads to very weak interlayer binding energy, which can significantly decrease the phonon interfacial scattering. The GFs also demonstrate excellent flexibility and high tensile strength, which is about three times higher than PGS. Therefore, GFs with optimized structures and properties show great potentials in thermal management of form-factor-driven electronics and other high-power-driven systems.
|
|
