| 1. |
- Lionikas, A., et al.
(författare)
-
Genetic determinants of weight of fast- and slow-twitch skeletal muscle in 500-day-old mice of the C57BL/6J and DBA/2J lineage.
- 2005
-
Ingår i: Physiological Genomics. - : American Physiological Society. - 1094-8341 .- 1531-2267. ; 21:2, s. 184-192
-
Tidskriftsartikel (refereegranskat)abstract
- C57BL/6J (B6) and DBA/2J (D2) strains and two derivative populations, BXD recombinant inbred strains (BXD RIs) and B6D2F2, were used to explore genetic basis for variation in muscle weight at 500 days of age. In parallel with findings in 200-day-old mice (Lionikas A, Blizard DA, Vandenbergh DJ, Glover MG, Stout JT, Vogler GP, McClearn GE, and Larsson L. Physiol Genomics 16: 141-152, 2003), weight of slow-twitch soleus, mixed gastrocnemius, and fast-twitch tibialis anterior (TA) and extensor digitorum longus (EDL) muscles was 13-22% greater (P < 0.001) in B6 than in D2. Distribution of BXD RI strain means indicated that genetic influence on muscle weight (strain effect P < 0.001, all muscles) was of polygenic origin, and effect of genetic factors differed between males and females (strain-by-sex interaction: P < 0.01 for soleus, EDL; P < 0.05 for TA, gastrocnemius). Linkage analyses in B6D2F2 population identified QTL affecting muscle weight on Chr 1, 2, 6, and 9. Pleiotropic influences were observed for QTL on Chr 1 (soleus, TA), 2 (TA, EDL, gastrocnemius), and 9 (soleus, TA, EDL) and were not related to muscle type (fast/slow-twitch) or function (flexor/extensor). Effect of QTL on Chr 9 on soleus muscle was male specific. QTL on Chr 2 and 6 were previously observed at 200 days of age, whereas QTL on Chr 1 and 9 are novel muscle weight QTL. In summary, muscle weight in B6/D2 lineage is affected by a polygenic system that has variable influences at different ages, between males and females, and across muscles in a manner independent of muscle type.
|
|
| 2. |
- Larsson, Cecilia, et al.
(författare)
-
Measurement and modeling of residual stress in a welded Haynes® 25 cylinder
- 2005
-
Ingår i: Materials Science & Engineering. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 399:1-2, s. 49-57
-
Tidskriftsartikel (refereegranskat)abstract
- An experimental and simulation study of residual stresses was made in the vicinity of a gas tungsten arc weld, used to join a hemispherical end cap to a cylinder. The capped cylinder is used in a satellite application and was fabricated from a Co-based Haynes® 25 alloy. The cylinder was 34.7 mm in outer diameter and 3.3 mm in thickness. The experimental measurements were made by neutron diffraction and the simulation used the implicit Marc finite element code. The experimental resolution was limited to approximately 3 mm parallel to the axis of the cylinder (the weld was 6 mm in the same direction) and comparison over the same volume of the finite element prediction showed general agreement. Subject to the limited spatial resolution, the largest experimentally measured tensile residual stress was 180 MPa, located at the middle of the weld. However, the predictions suggest that there are regions in the weld where average tensile residual stresses as much as 400 MPa exist. One qualitative disparity between the model and the experiments was that the measurement included a larger degree of asymmetry on either side of the weld than predicted by the model.
|
|
