| 1. |
|
|
| 2. |
- Hirai, T., et al.
(författare)
-
Characterization and heat flux testing of beryllium coatings on Inconel for JET ITER-like wall project
- 2007
-
Ingår i: Physica Scripta. - 0031-8949 .- 1402-4896. ; T128, s. 166-170
-
Tidskriftsartikel (refereegranskat)abstract
- In order to perform a fully integrated material test, JET has launched the ITER-like wall project with the aim of installing a full metal wall during the next major shutdown. The material foreseen for the main chamber wall is bulk Be at the limiters and Be coatings on inconel tiles elsewhere. R&D process comprises global characterization ( structure, purity etc) of the evaporated films and testing of their performance under heat loads. The major results are (i) the layers have survived energy loads of 20 MJ m(-2) which is significantly above the required level of 5 - 10 MJ m(-2), (ii) melting limit of beryllium coating would be at the energy level of 30 MJ m(-2), (iii) cyclic thermal load of 10 MJ m(-2) for up to 50 cycles have not induced any noticeable damage such as flaking or detachment.
|
|
| 3. |
|
|
| 4. |
- Ivanova, Darya, et al.
(författare)
-
Survey of dust formed in the TEXTOR tokamak : structure and fuel retention
- 2009
-
Ingår i: Physica scripta. T. - : Institute of Physics Publishing (IOPP). - 0281-1847. ; T138, s. 014025-
-
Tidskriftsartikel (refereegranskat)abstract
- A detailed survey of erosion and deposition on plasma-facing components was performed in the TEXTOR tokamak. Co-deposits and dust particles were collected from graphite limiters and from several locations on the Inconel liner. The total amount of dust (loose material), originating mainly from carbon-rich co-deposits detached from the limiters and the liner, was around 2 g, with sizes from 0.1 mu m to 1 mm. The morphology and fuel retention was determined using microscopy methods, ion beam analysis and thermal desorption spectrometry. The study revealed differences in structure and fuel content between deposits from the toroidal and main poloidal limiters. There were also splashes, up to 1 mm in diameter, of molten metal (mainly nickel) on the toroidal limiters. Issues of the dust conversion factor (erosion-to-dust) are addressed and a comparison with results of previous dust surveys at TEXTOR is also briefly presented.
|
|
| 5. |
|
|
| 6. |
- Kreter, A., et al.
(författare)
-
Deuterium retention in different carbon materials exposed in TEXTOR :
- 2008
-
Ingår i: PROCEEDINGS OF THE 17TH INTERNATIONAL VACUUM CONGRESS/13TH INTERNATIONAL CONFERENCE ON SURFACE SCIENCE/INTERNATIONAL CONFERENCE ON NANOSCIENCE AND TECHNOLOGY. - Bristol : IOP PUBLISHING LTD. ; , s. 062024-
-
Konferensbidrag (refereegranskat)abstract
- CFC NB31, CFC DMS780 and fine-grain graphite EK98 were simultaneously exposed in the SOL of TEXTOR in order to measure the retention of deuterium in the material bulk. After exposure, the samples were analysed by thermal desorption spectrometry and nuclear reaction analysis with a conventional beam as well as with a microbeam. The deuterium retention amounts (2-4).10(21) D/m(2) for the incident fluence of similar to 2.10(25) D/m(2). The retention values are similar for both CFC materials and lower by similar to 20-40% for EK98. The retention in all three materials scales roughly with a square root of incident fluence without saturation for the range of fluences obtained. The majority of deuterium is stored in a surface layer of <8 mu m. However, in NB31 deuterium is detectable as deep as 80 mu m. The in-bulk retention estimated for a TEXTOR experimental campaign of approximate to 7500 s of plasma has a contribution of approximate to 10% to the total retention, which is dominated by deuterium-carbon co-deposition.
|
|
| 7. |
- Krieger, K., et al.
(författare)
-
Be wall sources and migration in L-mode discharges after Be evaporation in the JET tokamak
- 2009
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 390-91, s. 110-114
-
Tidskriftsartikel (refereegranskat)abstract
- First wall material erosion and migration after fresh Be evaporation in the JET tokamak were studied in a series of consecutive identical L-mode discharges. The evolution of Be and C wall and divertor sources towards steady state conditions after deposition of a finite amount of Be at the carbon first wall of JET by the beryllium evaporation procedure provides a data set for benchmarking impurity transport simulations. Furthermore the experiment serves as a reference case for comparison of Be erosion to that of the planned ITER-like wall experiment with mainly Be plasma facing components (PFCs) in the main chamber. The experimental results confirm the migration pattern obtained by campaign integrated accounting of impurity sources and sinks, which is characterised by the main chamber wall and outer divertor as erosion dominated zones and migration of eroded material predominantly to the inner divertor where the material is finally deposited at the target plates.
|
|
| 8. |
|
|
| 9. |
- Psoda, M., et al.
(författare)
-
Material mixing on plasma-facing components : Compound formation
- 2009
-
Ingår i: Journal of Nuclear Materials. - : Elsevier. - 0022-3115 .- 1873-4820. ; 386-388, s. 740-743
-
Tidskriftsartikel (refereegranskat)abstract
- Two different tungsten limiters (castellated bulk metal block and W-coated graphite), subjected to high power loads in the TEXTOR tokamak, were examined in order to determine chemical composition of deposits inside the castellated grooves and on side surfaces of the coated limiter. Comprehensive analyses carried out by X-ray diffraction, ion beam analysis and other methods revealed: (i) the formation of tungsten oxide (WO2) inside the castellated grooves: (ii) the formation of tungsten carbides (WC main phase and traces of W2C) on side surfaces of the coated limiter. Elemental tungsten was found in deposits on side surfaces only in trace quantities thus indicating that tungsten eroded from the limiter top and transported to the scrape-off layer reacted with carbon. Based on thermodynamic data, the pathways leading to the formation of compounds are discussed.
|
|
| 10. |
|
|
