| 1. |
- Acuña, José, 1982-
(author)
-
Distributed thermal response tests : New insights on U-pipe and Coaxial heat exchangers in groundwater-filled boreholes
- 2013
-
Artistic work (other academic/artistic)abstract
- U-pipe Borehole Heat Exchangers (BHE) are widely used today in ground source heating and cooling systems in spite of their less than optimal performance. This thesis provides a better understanding on the function of U-pipe BHEs and Investigates alternative methods to reduce the temperature difference between the circulating fluid and the borehole wall, including one thermosyphon and three different types of coaxial BHEs.Field tests are performed using distributed temperature measurements along U-pipe and coaxial heat exchangers installed in groundwater filled boreholes. The measurements are carried out during heat injection thermal response tests and during short heat extraction periods using heat pumps. Temperatures are measured inside the secondary fluid path, in the groundwater, and at the borehole wall. These type of temperature measurements were until now missing.A new method for testing borehole heat exchangers, Distributed Thermal Response Test (DTRT), has been proposed and demonstrated in U-pipe, pipe-in-pipe, and multi-pipe BHE designs. The method allows the quantification of the BHE performance at a local level.The operation of a U-pipe thermosyphon BHE consisting of an insulated down-comer and a larger riser pipe using CO2 as a secondary fluid has been demonstrated in a groundwater filled borehole, 70 m deep. It was found that the CO2 may be sub-cooled at the bottom and that it flows upwards through the riser in liquid state until about 30 m depth, where it starts to evaporate.Various power levels and different volumetric flow rates have been imposed to the tested BHEs and used to calculate local ground thermal conductivities and thermal resistances. The local ground thermal conductivities, preferably evaluated at thermal recovery conditions during DTRTs, were found to vary with depth. Local and effective borehole thermal resistances in most heat exchangers have been calculated, and their differences have been discussed in an effort to suggest better methods for interpretation of data from field tests.Large thermal shunt flow between down- and up-going flow channels was identified in all heat exchanger types, particularly at low volumetric flow rates, except in a multi-pipe BHE having an insulated central pipe where the thermal contact between down- and up-coming fluid was almost eliminated.At relatively high volumetric flow rates, U-pipe BHEs show a nearly even distribution of the heat transfer between the ground and the secondary fluid along the depth. The same applies to all coaxial BHEs as long as the flow travels downwards through the central pipe. In the opposite flow direction, an uneven power distribution was measured in multi-chamber and multi-pipe BHEs.Pipe-in-pipe and multi-pipe coaxial heat exchangers show significantly lower local borehole resistances than U-pipes, ranging in average between 0.015 and 0.040 Km/W. These heat exchangers can significantly decrease the temperature difference between the secondary fluid and the ground and may allow the use of plain water as secondary fluid, an alternative to typical antifreeze aqueous solutions. The latter was demonstrated in a pipe-in-pipe BHE having an effective resistance of about 0.030 Km/W.Forced convection in the groundwater achieved by injecting nitrogen bubbles was found to reduce the local thermal resistance in U-pipe BHEs by about 30% during heat injection conditions. The temperatures inside the groundwater are homogenized while injecting the N2, and no radial temperature gradients are then identified. The fluid to groundwater thermal resistance during forced convection was measured to be 0.036 Km/W. This resistance varied between this value and 0.072 Km/W during natural convection conditions in the groundwater, being highest during heat pump operation at temperatures close to the water density maximum.
|
|
| 2. |
- Kharazmi, Parastou, 1977-
(author)
-
Evaluation of Innovative Rehabilitation Technologies Utilising Polymer Composites for Aging Sewer Systems
- 2019
-
Doctoral thesis (other academic/artistic)abstract
- Water and wastewater sewer system maintenance is among the costliest aspects of infrastructure investment. The replacement of deteriorated lines is a difficult and expensive process that causes community disturbance and is generally not conducted fast enough to meet demand. To keep up with the rate of deterioration, the use of alternative rehabilitation technologies using polymer linings has increased significantly in recent years, both within Sweden and worldwide. Compared to the traditional pipe replacement method, these technologies are cost-effective, create less community disturbance, and offer a quick return to the service for the line. The main function of polymeric lining is to stabilise the condition of the pipeline, eliminate deterioration, and thereby extend the pipeline’s service life. Although rehabilitation technologies employing polymeric systems have been in use for over 30 years, there have been few technical assessments of either these technologies or the materials involved. Data gathered through the evaluation of these innovative technologies can make their benefits and limitations more widely understood, and can also be used to increase the effectiveness of the rehabilitation process in future.The main objective of this work was to contribute to an improved understanding of the most commonly used materials and methods employed in rehabilitation of wastewater and other applicable sewer lines in residential buildings in Sweden. The primary objective was not to prove that the emerging rehabilitation technologies work, but rather to increase knowledge of their weaknesses and strengths, identify any issues, and provide a technical assessment to support realistic expectations of pipeline rehabilitation. Gathering technical information in this way will help with the planning of future investigations; moreover, collecting extensive data will help to increase the effectiveness of the renewal works, aid progress in the field, and improve predictions regarding longevity and service life. As pipeline rehabilitation is still considered novel, and owing to the general lack of available data on the subject, a multi-approach study was carried out: this included evaluation of the polymeric materials’ performance in the presence of deteriorative factors, assessing the in-service state of the materials and lined sewers previously installed, monitoring the level of quality control implemented during previous rehabilitation works, and evaluating the environmental impacts of using pipe-lining technologies compared to pipe replacement. The techniques discussed included rehabilitation with epoxy and polyester resin-based lining materials, applied with brush-on and spray-on techniques, and cured-in-place pipe lining (installed by sending a resin-impregnated flexible tube inside the host pipe). Degradation of the resin-based lining materials was investigated via artificial aging involving immersion in water at elevated temperatures. The changes in materials that occurred during accelerated laboratory aging were tracked by means of various tests, including thermal and mechanical analyses, water absorption measurements and microscopy. The analysis focused on reinforced polyester-based and toughened epoxy-based lining materials in order to gain a better understanding of their performance as pipe lining. Moreover, the previously installed lined pipes and lining materials were also studied during laboratory examinations to evaluate the in-service performance of the materials and techniques under operating conditions over time, as well as to identify common defects. The state of the materials and the lined pipe were studied by means of different investigative methods, including visual inspection, microscopy, Fourier transform infrared spectroscopy, thickness measurement, thermal and mechanical analyses. This PhD work also includes an investigation to determine the level of quality control carried during some previous rehabilitation works. Data on the quality evaluation of previous rehabilitation works were gathered during visits to the work sites, as well as by analysing lined pipes that had already been installed. Finally, a comparative life-cycle assessment was undertaken to compare the environmental impacts of pipe replacement with those of alternative innovative rehabilitations, such as CIPP and coatings with polyester and epoxy polymeric systems. Data obtained from an LCA tool were used to facilitate comparison from an environmental perspective.Results from artificial aging in the lab indicated that the properties of polymeric lining materials changed significantly when high temperatures were combined with water exposure. However, the aging testing conducted for this study also found that the materials performed relatively well at temperatures close to the average temperatures inside sewerage systems. The results revealed that the polyester-based lining material was less sensitive when compared with epoxy-based lining materials during stimulated aging. Moreover, results from the in-service field demonstration (involving examination of 12 samples with up to 10 years of service, including reinforced polyester and modified epoxy linings or cured-in-place pipe (CIPP) lining) showed minimal evidence that the materials underwent significant deterioration after installation; instead, a majority of the common defects were found to be related to poor-quality installation practices. Because very few field samples were available to study, conclusions regarding overall performance could not be drawn. However, there is no evidence that these materials will not perform as expected during their service life when properly installed.Evaluating quality control of previous rehabilitation work revealed a gap between theory and practice where the level of quality control and documentation was concerned; furthermore, it also emerged that quality control and documentation is crucial to both the prevention of common issues and the overall effectiveness of the rehabilitation. Accordingly, a series of recommendations regarding the development of comprehensive quality control and quality assurance procedures (QC/QA) are provided in this work. These recommendations highlight the aspects that are most important to consider at each of several key stages (before installation, during installation, and after rehabilitation work is completed).Results from comparative life-cycle assessment (LCA) showed that alternative technologies, including cured-in-place (flexible sleeve) and coating techniques, have some advantages over pipe replacement from an environmental perspective. However, the choice to use one rehabilitation technology over another is a multi-stage decision-making process that should not be based solely on a single factor.This PhD work promotes an improved understanding of the limitations and benefits of polymeric lining through the testing performed and analyses conducted. This work highlights the need for improved quality control, and further suggests that developing a detailed and comprehensive quality control plan for each technology would provide higher and more consistent quality overall. The study also demonstrates that the long-term strength of any rehabilitation work depends on various factors, and that selecting one method over another must be a process based on extensive knowledge and understanding of each rehabilitation technology. No evidence was found to indicate that the materials could not perform well under working conditions if selected and installed appropriately. However, a larger number of field samples with longer in-service time and a more detailed technical history, along with a more extended experimental plan for laboratory investigations based on the results of this PhD work, will allow for the gathering of the data required to answer questions regarding life expectancy with a higher degree of certainty.
|
|
| 3. |
- Martufi, Giampaolo, 1980-
(author)
-
Biomechanics of abdominal aortic aneurysm:Experimental evidence and multiscale constitutive modeling
- 2012
-
Doctoral thesis (other academic/artistic)abstract
- The reliable assessment of Abdominal Aortic Aneurysm (AAA) rupture risk is critically important in reducing related mortality without unnecessarily increasing the rate of elective repair. A multi-disciplinary approach including vascular biomechanics and constitutive modeling is needed to better understand and more effectively treat these diseases. AAAs are formed through irreversible pathological remodeling of the vascular wall and integrating this biological process in the constitutive description could improve the current understanding of this disease as well as the predictability of biomechanical simulations.First in this thesis, multiple centerline-based diameter measurements between renal arteries and aortic bifurcation have been used to monitor aneurysm growth of in total 51 patients from Computer Tomography-Angiography (CT-A) data. Secondly, the thesis proposes a novel multi-scale constitutive model for the vascular wall, where collagen fibers are assembled by proteoglycan cross-linked collagen fibrils and reinforce an otherwise isotropic matrix (elastin). Collagen fibrils are dynamically formed by a continuous stretch-mediated process, deposited in the current configuration and removed by a constant degradation rate. The micro-plane concept is then used for the Finite Element (FE) implementation of the constitutive model. Finally, histological slices from intra-luminal thrombus (ILT) tissue were analyzed using a sequence of automatic image processing steps. Derived microstructural data were used to define Representative Volume Elements (RVEs), which in turn allowed the estimation of microscopic material properties using the non-linear FE.The thesis showed that localized spots of fast diameter growth can be detected through multiple centerline-based diameter measurements all over the AAA sac. Consequently, this information might further reinforce the quality of aneurysm surveillance programs. The novel constitutive model proposed in the thesis has a strong biological motivation and provides an interface with biochemistry. Apart from modeling the tissue’s passive response, the presented model is helpful to predict saline feature of aneurysm growth and remodeling. Finally, the thesis provided novel microstructural and micromechanical data of ILT tissue, which is critically important to further explore the role of the ILT in aneurysm rupture.
|
|
| 4. |
- Fu, Qilin, 1986-
(author)
-
High dynamic stiffness nano-structured composites for vibration control : A Study of applications in joint interfaces and machining systems
- 2015
-
Doctoral thesis (other academic/artistic)abstract
- Vibration control requires high dynamic stiffness in mechanical structures for a reliable performance under extreme conditions. Dynamic stiffness composes the parameters of stiffness (K) and damping (η) that are usually in a trade-off relationship. This thesis study aims to break the trade-off relationship.After identifying the underlying mechanism of damping in composite materials and joint interfaces, this thesis studies the deposition technique and physical characteristics of nano-structured HDS (high dynamic stiffness) composite thick-layer coatings. The HDS composite were created by enlarging the internal grain boundary surface area through reduced grain size in nano scale (≤ 40 nm). The deposition process utilizes a PECVD (Plasma Enhanced Chemical Vapour Deposition) method combined with the HiPIMS (High Power Impulse Magnetron Sputtering) technology. The HDS composite exhibited significantly higher surface hardness and higher elastic modulus compared to Poly(methyl methacrylate) (PMMA), yet similar damping property. The HDS composites successfully realized vibration control of cutting tools while applied in their clamping interfaces.Compression preload at essential joint interfaces was found to play a major role in stability of cutting processes and a method was provided for characterizing joint interface properties directly on assembled structures. The detailed analysis of a build-up structure showed that the vibrational mode energy is shifted by varying the joint interface’s compression preload. In a build-up structure, the location shift of vibration mode’s strain energy affects the dynamic responses together with the stiffness and damping properties of joint interfaces.The thesis demonstrates that it is possible to achieve high stiffness and high damping simultaneously in materials and structures. Analysis of the vibrational strain energy distribution was found essential for the success of vibration control.
|
|
| 5. |
- Kothapalli, Satya V.V.N. 1985-
(author)
-
Nano-Engineered Contrast Agents : Toward Multimodal Imaging and Acoustophoresis
- 2015
-
Doctoral thesis (other academic/artistic)abstract
- Diagnostic ultrasound (US) is safer, quicker and cheaper than other diagnostic imaging modalities. Over the past two decades, the applications of US imaging has been widened due to the development of injectable, compressible and encapsulated microbubbles (MBs) that provide an opportunity to improve conventional echocardiographic imaging, blood flow assessment and molecular imaging. The encapsulating material is manufactured by different biocompatible materials such as proteins, lipids or polymers. In current research, researchers modify the encapsulated shell with the help of advanced molecular chemistry techniques to load them with dyes (for fluorescent imaging), nanoparticles and radioisotopes (for multimodal imaging) or functional ligands or therapeutic gases (for local drug delivery). The echogenicity and the radial oscillation of MBs is the result of their compressibility, which undoubtedly varies with the encapsulated shell characteristics such as rigidity or elasticity.In this thesis, we present acoustic properties of novel type of polyvinyl alcohol (PVA)-shelled microbubble (PVA-MB) that was further modified with superparamagnetic iron oxide nanoparticles (SPIONs) to work as a dual-modal contrast agent for magnetic resonance (MR) imaging along with US imaging. Apparently, the shell modification changes their mechanical characteristics, which affects their acoustic properties. The overall objective of the thesis is to investigate the acoustic properties of modified and unmodified PVA-MBs at different ultrasound parameters.The acoustic and mechanical characterization of SPIONs modified PVA-MBs revealed that the acoustical response depends on the SPION inclusion strategy. However they retain the same structural characteristics after the modification. The modified MBs with SPIONs included on the surface of the PVA shell exhibit a soft-shelled behavior and produce a higher echogenicity than the MBs with the SPIONs inside the PVA shell. The fracturing mechanism of the unmodified PVA-MBs was identified to be different from the other fracturing mechanisms of conventional MBs. With the interaction of high-pressure bursts, the air gas core is squeezed out through small punctures in the PVA shell. During the fracturing, the PVA-MBs exhibit asymmetric (other modes) oscillations, resulting in sub- and ultra-harmonic generation. Exploiting the US imaging at the other modes of the oscillation of the PVA-MBs would provide an opportunity to visualize very low concentrations of (down to single) PVA-MBs. We further introduced the PVA-MBs along with particles mimicking red blood cells in an acoustic standing-wave field to observe the acoustic radiation force effect. We observed that the compressible PVA-MBs drawn toward pressure antinode while the solid blood phantoms moved toward the pressure node. This acoustic separation method (acoustophoresis) could be an efficient tool for studying the bioclearance of the PVA-MBs in the body, either by collecting blood samples (in-vitro) or by using the extracorporeal medical procedure (ex-vivo) at different organs.Overall, this work contributes significant feedback for chemists (to optimize the nanoparticle inclusion) and imaging groups (to develop new imaging sequences), and the positive findings pave new paths and provide triggers to engage in further research.
|
|
| 6. |
- Mill, O., et al.
(author)
-
Analysis and development of hydro power research : synthesis within Swedish Hydro Power Centre
- 2010
-
Reports (other academic/artistic)abstract
- The market for hydropower re-investments in Sweden is approx 2.5 billion SEK/yr the coming decade. Large investments will also be carried out in Swedish tailing dams. This will result in challenging projects and need of experts. A crucial factor for a successful management of these challenges is the supply of engineers and researchers with hydro power and dam skills and knowledge. Swedish Hydro Power Centre (Svenskt vattenkraftcentrum, SVC) is a competence centre for university education and research environments within hydro power and mining dams. SVC comprises of two knowledge areas: Hydraulic Engineering and Hydro Turbines and Generators, respectively. SVC builds high-quality and long term sustainable knowledge at selected universities...
|
|
| 7. |
- Pardon, Gaspard, 1983-
(author)
-
From Macro to Nano : Electrokinetic Transport and Surface Control
- 2014
-
Doctoral thesis (other academic/artistic)abstract
- Today, the growing and aging population, and the rise of new global threats on human health puts an increasing demand on the healthcare system and calls for preventive actions. To make existing medical treatments more efficient and widely accessible and to prevent the emergence of new threats such as drug-resistant bacteria, improved diagnostic technologies are needed. Potential solutions to address these medical challenges could come from the development of novel lab-on-chip (LoC) for point-of-care (PoC) diagnostics.At the same time, the increasing demand for sustainable energy calls for the development of novel approaches for energy conversion and storage systems (ECS), to which micro- and nanotechnologies could also contribute.This thesis has for objective to contribute to these developments and presents the results of interdisciplinary research at the crossing of three disciplines of physics and engineering: electrokinetic transport in fluids, manufacturing of micro- and nanofluidic systems, and surface control and modification. By combining knowledge from each of these disciplines, novel solutions and functionalities were developed at the macro-, micro- and nanoscale, towards applications in PoC diagnostics and ECS systems.At the macroscale, electrokinetic transport was applied to the development of a novel PoC sampler for the efficient capture of exhaled breath aerosol onto a microfluidic platform.At the microscale, several methods for polymer micromanufacturing and surface modification were developed. Using direct photolithography in off-stoichiometry thiol-ene (OSTE) polymers, a novel manufacturing method for mold-free rapid prototyping of microfluidic devices was developed. An investigation of the photolithography of OSTE polymers revealed that a novel photopatterning mechanism arises from the off-stoichiometric polymer formulation. Using photografting on OSTE surfaces, a novel surface modification method was developed for the photopatterning of the surface energy. Finally, a novel method was developed for single-step microstructuring and micropatterning of surface energy, using a molecular self-alignment process resulting in spontaneous mimicking, in the replica, of the surface energy of the mold.At the nanoscale, several solutions for the study of electrokinetic transport toward selective biofiltration and energy conversion were developed. A novel, comprehensive model was developed for electrostatic gating of the electrokinetic transport in nanofluidics. A novel method for the manufacturing of electrostatically-gated nanofluidic membranes was developed, using atomic layer deposition (ALD) in deep anodic alumina oxide (AAO) nanopores. Finally, a preliminary investigation of the nanopatterning of OSTE polymers was performed for the manufacturing of polymer nanofluidic devices.
|
|
| 8. |
- Vastesson, Alexander
(author)
-
Thiol-ene and Thiol-ene-epoxy Based Polymers for Biomedical Microdevices
- 2017
-
Doctoral thesis (other academic/artistic)abstract
- Within healthcare there is a market pull for biomedical devices that can rapidly perform laboratory processes, such as diagnostic testing, in a hand-held format. For this reason, biomedical devices must become smaller, more sophisticated, and easier to use for a reasonable cost. However, despite the accelerating academic research on biomedical microdevices, and especially plastic-based microfluidic chips, there is still a gap between the inventions in academia and their benefit to society. To bridge this gap there is a need for new materials which both exhibit similar properties as industrial thermoplastics, and that enable rapid prototyping in academia.In this thesis, thiol-ene and thiol-ene-epoxy thermosets are evaluated both in terms of their suitability for rapid prototyping of biomedical microdevices and their potential for industrial manufacturing of “lab-on-chips”.The first part of the thesis focuses on material development of thiol-ene and thiol-ene-epoxy thermosets. Chemical and mechanical properties are studied, as well as in vitro biocompatibility with cells.The second part of the thesis focuses on microfabrication methods for both thermosets. This includes reaction injection molding, photostructuring, and surface modification. It is demonstrated how thiol-ene and thiol-ene-epoxy both provide advantageous thermo-mechanical properties and versatile surface modifications via “thiol-click chemistry”.In the end of the thesis, two applications for both polymer platforms are demonstrated. Firstly, thiol-ene is used for constructing nanoliter well arrays for liquid storage and on-demand electrochemical release. Secondly, thiol-ene-epoxy is used to enhance the biocompatibility of neural probes by tuning their flexibility.It is concluded that both thiol-ene and thiol-ene-epoxy thermosets exhibit several properties that are highly suitable for rapid prototyping as well as for scalable manufacturing of biomedical microdevices.
|
|
| 9. |
- Brandin, Jan, 1958-, et al.
(author)
-
A review of thermo-chemical conversion of biomass into biofuels-focusing on gas cleaning and up-grading process steps
- 2017
-
Reports (other academic/artistic)abstract
- It is not easy to replace fossil-based fuels in the transport sector, however, an appealing solution is to use biomass and waste for the production of renewable alternatives. Thermochemical conversion of biomass for production of synthetic transport fuels by the use of gasification is a promising way to meet these goals.One of the key challenges in using gasification systems with biomass and waste as feedstock is the upgrading of the raw gas produced in the gasifier. These materials replacing oil and coal contain large amounts of demanding impurities, such as alkali, inorganic compounds, sulphur and chlorine compounds. Therefore, as for all multi-step processes, the heat management and hence the total efficiency depend on the different clean-up units. Unfortunately, the available conventional gas filtering units for removing particulates and impurities, and also subsequent catalytic conversion steps have lower optimum working temperatures than the operating temperature in the gasification units.This report focuses on on-going research and development to find new technology solutions and on the key critical technology challenges concerning the purification and upgrading of the raw gas to synthesis gas and the subsequent different fuel synthesis processes, such as hot gas filtration, clever heating solutions and a higher degree of process integration as well as catalysts more resistant towards deactivation. This means that the temperature should be as high as possible for any particular upgrading unit in the refining system. Nevertheless, the temperature and pressure of the cleaned synthesis gas must meet the requirements of the downstream application, i.e. Fischer-Tropsch diesel or methanol.Before using the gas produced in the gasifier a number of impurities needs to be removed. These include particles, tars, sulphur and ammonia. Particles are formed in gasification, irrespective of the type of gasifier design used. A first, coarse separation is performed in one or several cyclone filters at high temperature. Thereafter bag-house filters (e.g. ceramic or textile) maybe used to separate the finer particles. A problem is, however, tar condensation in the filters and there is much work performed on trying to achieve filtration at as high a temperature as possible.The far most stressed technical barriers regarding cleaning of the gases are tars. To remove the tar from the product gas there is a number of alternatives, but most important is that the gasifier is operated at optimal conditions for minimising initial tar formation. In fluid bed and entrained flow gasification a first step may be catalytic tar cracking after particle removal. In fluid bed gasification a catalyst, active in tar cracking, may be added to the fluidising bed to further remove any tar formed in the bed. In this kind of tar removal, natural minerals such as dolomite and olivine, are normally used, or catalysts normally used in hydrocarbon reforming or cracking. The tar can be reformed to CO and hydrogen by thermal reforming as well, when the temperature is increased to 1300ºC and the tar decomposes. Another method for removing tar from the gas is to scrub it by using hot oil (200-300ºC). The tar dissolves in the hot oil, which can be partly regenerated and the remaining tar-containing part is either burned or sent back to the gasifier for regasification.Other important aspects are that the sulphur content of the gas depends on the type of biomass used, the gasification agent used etc., but a level at or above 100 ppm is not unusual. Sulphur levels this high are not acceptable if there are catalytic processes down-stream, or if the emissions of e.g. SO2 are to be kept down. The sulphur may be separated by adsorbing it in ZnO, an irreversible process, or a commercially available reversible adsorbent can be used. There is also the possibility of scrubbing the gas with an amine solution. If a reversible alternative is chosen, elementary sulphur may be produced using the Claus process.Furthermore, the levels of ammonia formed in gasification (3,000 ppm is not uncommon) are normally not considered a problem. When combusting the gas, nitrogen or in the worst case NOx (so-called fuel NOx) is formed; there are, however, indications that there could be problems. Especially when the gasification is followed by down-stream catalytic processes, steam reforming in particular, where the catalyst might suffer from deactivation by long-term exposure to ammonia.The composition of the product gas depends very much on the gasification technology, the gasifying agent and the biomass feedstock. Of particular significance is the choice of gasifying agent, i.e. air, oxygen, water, since it has a huge impact on the composition and quality of the gas, The gasifying agent also affects the choice of cleaning and upgrading processes to syngas and its suitability for different end-use applications as fuels or green chemicals.The ideal upgraded syngas consists of H2 and CO at a correct ratio with very low water and CO2 content allowed. This means that the tars, particulates, alkali salts and inorganic compounds mentioned earlier have to be removed for most of the applications. By using oxygen as the gasifying agent, instead of air, the content of nitrogen may be minimised without expensive nitrogen separation.In summary, there are a number of uses with respect to produced synthesis gas. The major applications will be discussed, starting with the production of hydrogen and then followed by the synthesis of synthetic natural gas, methanol, dimethyl ether, Fischer-Tropsch diesel and higher alcohol synthesis, and describing alternatives combining these methods. The SNG and methanol synthesis are equilibrium constrained, while the synthesis of DME (one-step route), FT diesel and alcohols are not. All of the reactions are exothermal (with the exception of steam reforming of methane and tars) and therefore handling the temperature increase in the reactors is essential. In addition, the synthesis of methanol has to be performed at high pressure (50-100 bar) to be industrially viable.There will be a compromise between the capital cost of the whole cleaning unit and the system efficiency, since solid waste, e.g. ash, sorbents, bed material and waste water all involve handling costs. Consequently, installing very effective catalysts, results in unnecessary costs because of expensive gas cleaning; however the synthesis units further down-stream, especially for Fischer-Tropsch diesel, and DME/methanol will profit from an effective gas cleaning which extends the catalysts life-time. The catalyst materials in the upgrading processes essentially need to be more stable and resistant to different kinds of deactivation.Finally, process intensification is an important development throughout chemical industries, which includes simultaneous integration of both synthesis steps and separation, other examples are advanced heat exchangers with heat integration in order to increase the heat transfer rates. Another example is to combine exothermic and endothermic reactions to support reforming reactions by using the intrinsic energy content. For cost-effective solutions and efficient application, new solutions for cleaning and up-grading of the gases are necessary.
|
|
| 10. |
- del Aguila Pla, Pol, 1990-
(author)
-
Inverse problems in signal processing : Functional optimization, parameter estimation and machine learning
- 2019
-
Doctoral thesis (other academic/artistic)abstract
- Inverse problems arise in any scientific endeavor. Indeed, it is seldom the case that our senses or basic instruments, i.e., the data, provide the answer we seek. It is only by using our understanding of how the world has generated the data, i.e., a model, that we can hope to infer what the data imply. Solving an inverse problem is, simply put, using a model to retrieve the information we seek from the data.In signal processing, systems are engineered to generate, process, or transmit signals, i.e., indexed data, in order to achieve some goal. The goal of a specific system could be to use an observed signal and its model to solve an inverse problem. However, the goal could also be to generate a signal so that it reveals a parameter to investigation by inverse problems. Inverse problems and signal processing overlap substantially, and rely on the same set of concepts and tools. This thesis lies at the intersection between them, and presents results in modeling, optimization, statistics, machine learning, biomedical imaging and automatic control.The novel scientific content of this thesis is contained in its seven composing publications, which are reproduced in Part II. In five of these, which are mostly motivated by a biomedical imaging application, a set of related optimization and machine learning approaches to source localization under diffusion and convolutional coding models are presented. These are included in Publications A, B, E, F and G, which also include contributions to the modeling and simulation of a specific family of image-based immunoassays. Publication C presents the analysis of a system for clock synchronization between two nodes connected by a channel, which is a problem of utmost relevance in automatic control. The system exploits a specific node design to generate a signal that enables the estimation of the synchronization parameters. In the analysis, substantial contributions to the identifiability of sawtooth signal models under different conditions are made. Finally, Publication D brings to light and proves results that have been largely overlooked by the signal processing community and characterize the information that quantized linear models contain about their location and scale parameters.
|
|
