| 1. |
- Khanzadi, M Reza, 1983, et al.
(författare)
-
Calculation of the Performance of Communication Systems from Measured Oscillator Phase Noise
- 2014
-
Ingår i: IEEE Transactions on Circuits and Systems I: Regular Papers. - 1549-8328 .- 1558-0806. ; 61:5, s. 1553-1565
-
Tidskriftsartikel (refereegranskat)abstract
- Oscillator phase noise (PN) is one of the major problems that affect the performance of communication systems. In this paper, a direct connection between oscillator measurements, in terms of measured single-side band PN spectrum, and the optimal communication system performance, in terms of the resulting error vector magnitude (EVM) due to PN, is mathematically derived and analyzed. First, a statistical model of the PN, considering the effect of white and colored noise sources, is derived. Then, we utilize this model to derive the modified Bayesian Cramer-Rao bound on PN estimation, and use it to find an EVM bound for the system performance. Based on our analysis, it is found that the influence from different noise regions strongly depends on the communication bandwidth, i.e., the symbol rate. For high symbol rate communication systems, cumulative PN that appears near carrier is of relatively low importance compared to the white PN far from carrier. Our results also show that 1/f^3 noise is more predictable compared to 1/f^2 noise and in a fair comparison it affects the performance less.
|
|
| 2. |
- Pérez-Penichet, Carlos, et al.
(författare)
-
Poster abstract : Augmenting WSNs with interoperable 802.15.4 sensor tags
- 2017
-
Ingår i: SenSys 2017 - Proceedings of the 15th ACM Conference on Embedded Networked Sensor Systems. - New York, NY, USA : Association for Computing Machinery, Inc. - 9781450354592
-
Konferensbidrag (refereegranskat)abstract
- The sensing capabilities of most sensor networks are fixed at the time of deployment. Adding new sensing capabilities to such networks is a costly and cumbersome process. We present Passive Sensor Tags, battery-free sensing devices that could be used to extend the sensing capabilities of an existing network. Sensor tags feature our new 802.15.4 receiver design which is suitable for micro-power operation, making battery-free tags possible. Because our tags can both transmit and receive 802.15.4 frames there is no need for any modification to the deployed hardware. We present preliminary measurements of transmission and reception range.
|
|
| 3. |
- Abbaspour Asadollah, Sara, et al.
(författare)
-
Evaluation of surface EMG-based recognition algorithms for decoding hand movements
- 2019
-
Ingår i: Medical and Biological Engineering and Computing. - : Springer. - 0140-0118 .- 1741-0444. ; 58:1, s. 83-100
-
Tidskriftsartikel (refereegranskat)abstract
- Myoelectric pattern recognition (MPR) to decode limb movements is an important advancement regarding the control of powered prostheses. However, this technology is not yet in wide clinical use. Improvements in MPR could potentially increase the functionality of powered prostheses. To this purpose, offline accuracy and processing time were measured over 44 features using six classifiers with the aim of determining new configurations of features and classifiers to improve the accuracy and response time of prosthetics control. An efficient feature set (FS: waveform length, correlation coefficient, Hjorth Parameters) was found to improve the motion recognition accuracy. Using the proposed FS significantly increased the performance of linear discriminant analysis, K-nearest neighbor, maximum likelihood estimation (MLE), and support vector machine by 5.5%, 5.7%, 6.3%, and 6.2%, respectively, when compared with the Hudgins’ set. Using the FS with MLE provided the largest improvement in offline accuracy over the Hudgins feature set, with minimal effect on the processing time. Among the 44 features tested, logarithmic root mean square and normalized logarithmic energy yielded the highest recognition rates (above 95%). We anticipate that this work will contribute to the development of more accurate surface EMG-based motor decoding systems for the control prosthetic hands. [Figure not available: see fulltext.].
|
|
| 4. |
- Farsi, Mohammad, 1994, et al.
(författare)
-
Pilot distributions for phase noise estimation in electro-optic frequency comb systems
- 2023
-
Ingår i: European Conference on Optical Communication, ECOC.
-
Konferensbidrag (refereegranskat)abstract
- We explore the optimal pilot positioning for phase tracking in electro-optic frequency comb setups. We show that, in contrast to previous results for regular multichannel systems, allocating the first and the last channels for pilots is optimal given a fixed pilot overhead.
|
|
| 5. |
- Kersten, Anton, 1991, et al.
(författare)
-
Battery Loss and Stress Mitigation in a Cascaded H-Bridge Multilevel Inverter for Vehicle Traction Applications by Filter Capacitors
- 2019
-
Ingår i: IEEE Transactions on Transportation Electrification. - 2332-7782. ; 5:3, s. 659-671
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, two types of filter capacitors of varying capacity, were connected to the battery packs of a cascaded H-Bridge single-star multilevel vehicle traction inverter, and their influence on the battery losses has been analyzed. The battery and capacitor simulation models used are experimentally verified in a down-scaled system. Different capacitor configurations were simulated for four drive cycle scenarios to determine the potentials for the mitigation of current pulse stresses and battery loss reduction with respect to the added weight. By adding capacitors corresponding to a weight of 4% of the initial battery storage, the peak current is reduced by 5%-20%, depending on the operating point from DC to a few kHz, and the battery losses are reduced by 10%. In comparison, it is demonstrated that adding supercapacitors is more beneficial for lower output frequencies, while adding electrolytic capacitors is better for higher output frequencies. Furthermore, the low-order voltage harmonics of the DC-rails between the converter and battery were reduced by 10%-30% for frequencies above 9 kHz, which decreases the potential of electromagnetic disturbances. In addition, during cold battery temperatures, when it is very important to avoid heavy cyclings, the loss reduction using the capacitors was 2.5 times larger than for nominal temperature.
|
|
| 6. |
- Kersten, Anton, 1991, et al.
(författare)
-
Fault Detection and Localization for Limp Home Functionality of Three-Level NPC Inverters with Connected Neutral Point for Electric Vehicles
- 2019
-
Ingår i: IEEE Transactions on Transportation Electrification. - 2332-7782. ; 5:2, s. 416-432
-
Tidskriftsartikel (refereegranskat)abstract
- This paper deals with the detection of single battery or inverter switch faults during operation of a common and an active three-level neutral-point-clamped (NPC) inverter with a connected neutral point. Here, the main focus lies on the detection and localization of open-circuit faults of the inverter's switches. Therefore, a fault detection algorithm, using a current estimator, and two fault localization algorithms, a pulse pattern injection principle and an online adaption of the space vector modulation (SVM), are investigated and verified through simulations and experiments. Also, investigated is how the powertrain can be operated under a fault condition, so that the vehicle can drive with a limited maximum power using an adapted SVM, referred to as "limp home" mode, to the next service station. It is shown, that an active NPC inverter can cope with any single short or open-circuit fault of the inverter's switches without bringing the vehicle to standstill, whereas a generic NPC inverter loses controllability if an open-circuit fault at an inner switch occurs. Furthermore, both inverter types are able to be operated just with half of the dc-link voltage in case of a failure in one part of the battery.
|
|
| 7. |
- Kersten, Anton, 1991, et al.
(författare)
-
Measuring and Separating Conducted Three-Wire Emissions from a Fault-Tolerant, NPC Propulsion Inverter with a Split-Battery Using Hardware Separators Based on HF Transformers
- 2021
-
Ingår i: IEEE Transactions on Power Electronics. - 0885-8993 .- 1941-0107. ; 36:1, s. 378-390
-
Tidskriftsartikel (refereegranskat)abstract
- Conducted emissions on the traction battery's power cables in EVs must be limited to avoid unwanted electromagnetic interference (EMI). When designing an EMI filter, it is advantageous to have information of the common mode (CM) and differential mode (DM) noise levels. This article deals with the measurement and separation of the dc side's three-wire DM/CM noise of a fault-tolerant three-level neutral-point-clamped (NPC) inverter with a split-battery system. Two hardware separators, based on small-circuit highfrequency transformers, were developed to identify the dc side's CM, line-DM, and phase-DM noise levels. Their characterized CM and DM rejection ratios for the frequency range from 150 kHz to 110 MHz are at least -33 and -21 dB, respectively. The separated noise of the NPC inverter was measured, using an inductive load, when operating the inverter with three-level and two-level modulation, resembling normal operation and a possible operation under fault, respectively. A simple three-wire CM model of the used testbed and the DM power module oscillation were derived to validate the separated noise's resonance peaks/valleys. It has been seen that the CM noise is dominant, especially below 10 MHz, except for the power module oscillations. Furthermore, when using the two-level modulation, in the case of a clamping diode fault, the noise levels are increased by about 3 dB.
|
|
| 8. |
- Kersten, Anton, 1991, et al.
(författare)
-
Online and On-Board Battery Impedance Estimation of Battery Cells, Modules or Packs in a Reconfigurable Battery System or Multilevel Inverter
- 2020
-
Ingår i: IECON Proceedings (Industrial Electronics Conference). - 2162-4704 .- 2577-1647. ; 2020-October, s. 1884-1891
-
Konferensbidrag (refereegranskat)abstract
- This paper shows two approaches to determine the battery impedance of battery cells or battery modules when used in a reconfigurable battery system (RBS) or in any type of modular multilevel converter (MMC) for electric drive applications. A generic battery model is used and the concepts of the recursive time and frequency-domain parameter extraction, using a current step and an electrochemical impedance spectroscopy, are explained. Thus, it is shown and demonstrated that the balancing current of neighboring cells/modules ,when in parallel operation, can be used, similar to the time-domain parameter extraction utilizing a current step, to determine the battery parameters. Furthermore, it is shown and demonstrated that a part of the inverter can be used as variable AC voltage source to control a sinusoidal current through the motor inductances of the drive train, which can be injected to the inserted battery cells/modules of an adjacent phase to perform an on-board impedance spectroscopy. Using either of the two presented approaches, the individual battery impedances can be easily determined, yielding the state of health (SOH) and the power capability of individual battery cells/modules. Nonetheless, the analyzed approaches were just considered to be applied at machine standstill, which is not suitable for grid-tied applications.
|
|
| 9. |
- Kuder, Manuel, et al.
(författare)
-
Exponential Modular Multilevel Converter for Low Voltage Applications
- 2019
-
Ingår i: 2019 21st European Conference on Power Electronics and Applications, EPE 2019 ECCE Europe. ; , s. 1-11
-
Konferensbidrag (refereegranskat)abstract
- This paper presents the structure and control of a single phase Exponential Modular Multilevel Converter (EMMC), which works as a bidirectional AC/DC converter. In addition to the main H-bridge converter, it uses series connected H-bridges with DC link capacitors. The nominal voltage rating of the capacitors is increased with each module by factor of two. In this manner, the number of output voltage levels exponentially increases with the number of series connected H-bridges. By using low-voltage MOSFETs it is possible to achieve a very high efficiency, especially at partial loading. The high number of voltage levels reduces the output voltage THD, while using a low switching frequency. Thus, the required grid filter size can be substantially reduced. Furthermore, the additional capacitor modules increase the nominal output voltage at the AC side, so that the flow of the active and reactive power can be dynamically adjusted. Therefore, the EMMC could be used, for instance, as a vehicle charger directly connected to the grid.
|
|
| 10. |
- Seyedhosseinzadeh, Neda, et al.
(författare)
-
A 100–140 GHz SiGe-BiCMOS sub-harmonic down-converter mixer
- 2017
-
Ingår i: 2017 12th European Microwave Integrated Circuits Conference (EuMIC). - 9782874870484 ; 2017-January
-
Konferensbidrag (refereegranskat)abstract
- This paper demonstrates a wideband, subharmonic down converting mixer using a commercial 130-nm SiGe-BiCMOS technology. The mixer adopts a frequency doubling LO-stage, a differential switched-transconductance RF-stage, on-chip LO and RF baluns, and two emitter-follower buffer-stages. The measured results exhibit a maximum conversion gain up to 2.6 dB over the frequency range of 100 to 140 GHz with a LO power of 5 dBm. The mixer achieves an input referred 1-dB compression point of −7.2 dBm, with a DC power of 46.3 mW, including 26.7 mW for buffer-stages. It demonstrates also up to 12 GHz 3-dB IF bandwidth, which to the authors' best knowledge, is the highest obtained among active sub-harmonic mixers operating above 100 GHz. The chip occupies 0.4 mm2, including pads.
|
|
