| 1. |
- Adamopoulou, Marianthi, et al.
(författare)
-
Improving Cardiac Auscultation Signal Quality by using 4-Channel Stethoscope Array
- 2024
-
Ingår i: Conference Record - IEEE Instrumentation and Measurement Technology Conference. - : IEEE conference proceedings. - 9798350380903
-
Konferensbidrag (refereegranskat)abstract
- In cardiac auscultation, the ability to clearly hear any existing murmur sounds in heart sounds is crucial for proper diagnosis. This work aims to improve heart sound by the use of a stethoscope array and beamforming technique. The stethoscope array comprises four piezo elements for measurement, placed on the edges of a 40mm by 40mm rectangle. The directionality of the piezo elements reduces the effect of ambient noise in the measurement. The signal amelioration is achieved by isolating the systole and diastole sounds, and independently applying the delay-and-sum beamforming. This thereby makes any existing murmur sounds in the systole and/or diastole more audible and clearer to aid diagnosis. Finally, the designed stethoscope array and signal processing shows a gain of up to 33% for measured healthy heart samples, and up to 63% increase in murmur sound gain for measured sample with medically confirmed murmur.
|
|
| 2. |
- Ainegren, Mats, 1963-, et al.
(författare)
-
Breathing resistance in automated metabolic systems is high in comparison with the Douglas Bag method and previous recommendations
- 2018
-
Ingår i: Proceedings of the Institution of Mechanical Engineers, Part P. - : SAGE Publications. - 1754-3371. ; 232:2, s. 122-130
-
Tidskriftsartikel (refereegranskat)abstract
- The purpose of this study was to investigate the resistance (RES) to breathing in metabolic systems used for the distribution and measurement of pulmonary gas exchange. A mechanical lung simulator was used to standardize selected air flow rates ( , L/s). The delta pressure (∆p, Pa) between ambient air and the air inside the equipment was measured in the breathing valve’s mouthpiece adapter for four metabolic systems and four types of breathing valves. RES for the inspiratory and expiratory sides was calculated as RES = ∆p / , Pa/L/s. The results for RES showed significant (p < 0.05) between-group variance among the tested metabolic systems, as well as the breathing valves and between most of the completed . The lowest RES among the metabolic systems was found for a Douglas Bag system, with approximately half of the RES compared to the automated metabolic systems. The automated systems were found to have higher RES already at low in comparison to previous recommendations. For the hardware components, the highest RES was found for the breathing valves while the lowest RES was found for the hoses. Conclusion: The results showed that RES in metabolic systems can be minimized through conscious choices of system design and hardware components.
|
|
| 3. |
- Andersson, Fredrik, et al.
(författare)
-
A Portable Douglas Bag System
- 2015
-
Ingår i: Congress Proceedings. - 9789513962166 ; , s. 59-
-
Konferensbidrag (refereegranskat)
|
|
| 4. |
- Petrone, Nicola, et al.
(författare)
-
A Novel Instrumented Human Head Surrogate For The Impact Evaluation Of Helmets
- 2018
-
Ingår i: Proceedings, Volume 2, ISEA 2018. - Basel Switzerland : MDPI. ; , s. 269-
-
Konferensbidrag (refereegranskat)abstract
- A novel Human Head Surrogate was obtained from available MRI scans of a 50th percentile male human head. Addictive manufacturing was used to produce the skull, the brain and the skin. All original MRI geometries were partially smoothed and adjusted to provide the best biofidelity compatible with printing and molding technology. The skull was 3D-printed in ABS and ten pressure sensors were placed into it. The brain surrogate was cast from silicon rubber in the 3d-printed plastic molds. Nine tri-axial accelerometers (placed at the tops of the lobes, at the sides of the lobes, in the cerebellum and in the center of mass) and a three-axis gyroscope (at the center of mass) were inserted into the silicon brain during casting. The cranium, after assembly with brain, was filled with silicon oil mimicking the cerebral fluid. Silicon rubber was cast in additional 3d-printed molds to form the skin surrounding the cranium. The skull base was adapted to be compatible with the Hybrid-III neck and allow the exit of brain sensors cabling. Preliminary experiments were carried out proving the functionality of the surrogate. Results showed how multiple accelerometers and pressure sensors allowed a better comprehension of the head complex motion during impacts.
|
|
