| 1. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Influence of heat treatment under hot isostatic pressing (HIP) on microstructure of intermetallic-reinforced tool steel manufactured by laser powder bed fusion
- 2020
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 772
-
Tidskriftsartikel (refereegranskat)abstract
- Microstructure and properties of as-built laser powder bed fusion (LPBF) steels differ from the conventional ones, and they may contain some porosity and lack of fusion. Therefore, post-treatments, including hot isostatic pressing (HIP), are used to density the material, and tailor the properties of the final product. Usually, HIP is performed as an operation separate from heat treatment. In the present investigation a new approach was used, in which the whole cycle of the heat treatment was carried out in HIP under pressure, and the influence of HIP on microstructure of an advanced stainless maraging tool steel manufactured by LPBF was investigated. For a comparison, a conventional steel grade of the same chemical composition, after a heat treatment at the same temperature-time conditions, was also characterized. The microstructure of the steel was investigated by means of advanced microscopy and atom probe tomography. The influence of the manufacturing route, heat treatment and HIP on microstructure, austenitic phase fraction and size distribution of precipitates was investigated, and the role of high pressure in stabilization of austenite in the microstructure was discussed. It was concluded that since HIP influences phase transformations, a fundamental understanding of the influence of HIP on microstructure is nececcary, and development of new post processing regimes guaranteeing the best performance of the material is required.
|
|
| 2. |
- Xu, Jinghao, et al.
(författare)
-
On the strengthening and embrittlement mechanisms of an additively manufactured Nickel-base superalloy
- 2020
-
Ingår i: Materialia. - : Elsevier BV. - 2589-1529. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- The γ′ phase strengthened Nickel-base superalloy is one of the most significant dual-phase alloy systems for high-temperature engineering applications. The tensile properties of laser powder-bed-fused IN738LC superalloy in the as-built state have been shown to have both good strength and ductility compared with its post-thermal treated state. A microstructural hierarchy composed of weak texture, sub-micron cellular structures and dislocation cellular walls was promoted in the as-built sample. After post-thermal treatment, the secondary phase γ′ precipitated with various size and fraction depending on heat treatment process. For room-temperature tensile tests, the dominated deformation mechanism is planar slip of dislocations in the as-built sample while dislocations bypassing the precipitates via Orowan looping in the γ′ strengthened samples. The extraordinary strengthening effect due to the dislocation substructure in the as-built sample provides an addition of 372 MPa in yield strength. The results of our calculation are in agreement with experimental yield strength for all the three different conditions investigated. Strikingly, the γ′ strengthened samples have higher work hardening rate than as-built sample but encounter premature failure. Experimental evidence shows that the embrittlement mechanism in the γ′ strengthened samples is caused by the high dislocation hardening of the grain interior region, which reduces the ability to accommodate further plastic strain and leads to premature intergranular cracking. On the basis of these results, the strengthening micromechanism and double-edge effect of strength and ductility of Nickel-base superalloy is discussed in detail.
|
|
| 3. |
- Hanning, Fabian, et al.
(författare)
-
The Effect of Grain Size on theSusceptibility Towards Strain Age Crackingof Wrought Haynes® 282®
- 2020
-
Ingår i: SPS 2020. - Amsterdam : IOS Press. - 9781643681467 - 9781643681474 ; 13, s. 407-416
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The effect of grain size on the suceptibility towards strain age cracking (SAC) has been investigated for Haynes® 282® in the tempeature range of 750 to 950°C after isothermal exposure up to 1800s. Grain growth was induced by heattreating the material at 1150°C for 2h, resulting in a fourfold increase in grain size. Hardness was significanlty reduced after heat treatment as compared to millannealed material. Large grain size resulted in intergranular fracture over a widertemperature range than small grain size material. Ductility was lowest at 850°C, while lower values were observed to be correlated to increased grain size. The rapid formation of grain boundary carbide networks in Haynes® 282® is found to be notable to compensate for higher local stresses on grain boundaries due to incresedgrain size.
|
|
| 4. |
- Shoja, Siamak, 1980
(författare)
-
Microstructure and plastic deformation of textured CVD alumina coatings
- 2020
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- It is known that the wear performance of α-alumina coatings produced by chemical vapor deposition (CVD) is significantly influenced by the type and degree of texture. However, the main reasons behind this behavior are not fully understood. This thesis contains studies of two related topics for increasing the understanding of α-alumina coatings. The first topic concerns the microstructure and texture development of CVD α-Al2O3 coatings, and the second topic concerns calculations and analysis of the Schmid factors ( m ) for coatings with different textures. By combining different analysis methods (such as XRD, SEM, FIB/SEM, TKD, TEM, STEM, XEDS), and theoretical and experimental Schmid factor analysis by MATLAB and EBSD, the microstructure and plastic deformation of α-alumina coatings were investigated. The microstructures of three different CVD α-Al2O3 layers deposited onto a Ti(C,N,O) bonding layer were studied. Grain boundary diffusion of heavy elements from the substrate to the bonding layer/α-Al2O3 interface was observed. This may be the cause of a disturbance in the early growth of α-Al2O3. Additionally, it was found that the number of interfacial pores at the bonding layer/α-Al2O3 interface increased by introducing the H2S gas. The H2S gas also promoted an earlier development of the (0001) texture. The orientation of the grains was developed to the desired texture both as a gradual change over several grains and as an abrupt transformation from one grain to another. The probability of plastic deformation in different wear zones on the rake face of a cutting tool was investigated theoretically and experimentally by analyzing Schmid factors for textured α-Al2O3 coatings. Schmid factor diagrams were constructed using MATLAB/MTEX and used to extract frequency distributions for different slip systems and textures. The results were compared with lateral distribution maps of Schmid factors obtained from experimental coatings. It was observed that basal slip is most easily activated in the transition zone, followed by prismatic slip systems 1 and 2 in coatings with an (0001)-texture. The homogeneous plastic deformation behavior observed in this coating is also connected to mostly high Schmid factors in the m -value distribution. The differences between the m -value distributions for the three slip systems are not that pronounced in the (01-12) and (11-20) textures, and the distributions are relatively wide. The low wear rate and more homogeneous deformation of the coating with (0001) texture compared to the other coating textures may be the result of the high plasticity, offered by the easy activation of basal slip and prismatic 1 slip, and the low spread of Schmid factor values at the transition zone. In conclusion, the results presented in this thesis form a knowledge platform that can be used to understand the microstructure and wear mechanisms of textured CVD α-alumina coatings.
|
|
| 5. |
- Guldris Leon, Lorena, 1983, et al.
(författare)
-
Understanding Mineral Liberation during Crushing Using Grade-by-Size Analysis - A Case Study of the Penuota Sn-Ta Mineralization, Spain
- 2020
-
Ingår i: Minerals. - : MDPI AG. - 2075-163X. ; 10:2
-
Tidskriftsartikel (refereegranskat)abstract
- Coarse comminution test-work and modeling are powerful tools in the design and optimization of mineral processing plants and provide information on energy consumption. Additional information on mineral liberation characteristics can be used for assessing the potential of pre-concentration stages or screens in the plant design. In ores of high-value metals (e.g., Ta, W), standard techniques-such as the mineralogical quantification of grain mounts by quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) or chemical analysis by X-ray fluorescence (XRF) can be challenging, due to the low relative abundance of such valuable minerals. The cost of QEMSCAN is also a limiting factor, especially considering the large number of samples required for the optimization of coarse comminution. In this study, we present an extended analytical protocol to a well-established mechanical test of interparticle breakage to improve the assessment of coarse mineral liberation characteristics. The liberation of ore minerals is a function of the rock texture and the difference in size and mechanical properties of the valuable minerals relative to gangue minerals and they may fraction in certain grain sizes if they behave differently during comminution. By analyzing the bulk-chemistry of the different grain size fractions produced after compressional testing, and by generating element by size diagrams, it is possible to understand the liberation characteristics of an ore. We show, based on a case study performed on a tantalum ore deposit, that element distribution can be used to study the influence of mechanical parameters on mineral liberation. This information can direct further mineralogical investigation and test work.
|
|
| 6. |
- Jaladurgam, Nitesh Raj, 1993, et al.
(författare)
-
Macro- and micro-mechanical behaviour of a γ′ strengthened Ni-based superalloy at cryogenic temperatures
- 2021
-
Ingår i: Materials and Design. - : Elsevier BV. - 1873-4197 .- 0264-1275. ; 209
-
Tidskriftsartikel (refereegranskat)abstract
- In-situ neutron diffraction was performed during tensile deformation of Ni-base superalloy, Haynes 282, at 20, 100 and 300 K. Two distinct uni-modal microstructures with fine (20 nm) and coarse (200 nm) \(\gamma^\prime\) particles were investigated. On the macro-scale yield strength increased and ductility decreased with decreasing temperature, although most significant decrease in ductility occurred between 100 and 20 K. The work hardening differed between the two microstructures, but was independent of temperature for each microstructure. On the micro-scale intergranular elastic interactions mainly lead to a transfer of the load to grains with the $\left<200\right>$ parallel to the tensile axis. No further load re-distribution between matrix and particles occurred in the microstructure with fine \(\gamma^\prime\), where shearing of precipitates lead to co-deformation at all temperatures. In the coarse \(\gamma^\prime\) microstructure, the load was transferred intragranularly from matrix to particles, in addition to the intergranular load transfer. The particles initially behaved elastically while the matrix deformed plastically, but at higher stresses a change in load partitioning indicated that also the \(\gamma^\prime\) phase underwent plastic deformation as a result of the elastic stress build-up from the load partitioning. The tendency for, and effect of, plastic deformation of \(\gamma^\prime\) increased with decreasing temperature.
|
|
| 7. |
- Jaladurgam, Nitesh Raj, 1993, et al.
(författare)
-
Microstructure-dependent deformation behaviour of a low γ′ volume fraction Ni-base superalloy studied by in-situ neutron diffraction
- 2020
-
Ingår i: Acta Materialia. - : Elsevier BV. - 1359-6454. ; 183, s. 182-195
-
Tidskriftsartikel (refereegranskat)abstract
- Ni-base superalloys are critical materials for numerous demanding applications in the energy and aerospace sectors. Their complex chemistry and microstructure require detailed understanding of the operating deformation mechanisms and interaction between the matrix and the hardening phase during plastic deformation. Here we use in-situ neutron diffraction to show that the dependence of the deformation mechanisms and load redistribution on $\gamma^\prime$ particle size in a Ni-base superalloy with a $\gamma^\prime$ volume fraction of around $20 \%$ can exhibit distinct differences compared to their high volume fraction counterparts. In particular, the load redistribution in the coarse microstructure occurs immediately upon yielding in the present case, whereas high $\gamma^\prime$ volume fractions have been observed to initially lead to shear mediated co-deformation before work hardening allows looping to dominate and cause load partitioning at higher stresses. The fine microstructure, on the other hand, behaved similar to high volume fraction alloys, exhibiting co-deformation of the phases due to particle shearing. A recently developed elasto-plastic self-consistent (EPSC) crystal plasticity model, specifically developed for the case of coherent multi-phase materials, could reproduce experimental data with good accuracy. Furthermore, the finite strain formulation of the EPSC model allowed deformation induced texture predictions. The correct trends were predicted by the simulations, but the rate of lattice rotation was slower than experimentally observed. The insights point towards necessary model developments and improvements in order to accurately predict e.g. texture evolution during processing and effect of texture and microstructure on component properties.
|
|
| 8. |
- Lozinko, Adrianna, 1992
(författare)
-
Microstructure development and mechanical properties of cast and thermo-mechanically treated eutectic high-entropy alloys
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The recently emerging high-entropy alloys (HEAs) present a novel alloying strategy, significantly expanding the scope of metal alloy design. Single-phase HEAs, nevertheless, suffer from the strength-ductility trade off as seen in conventional metallic materials. A possible solution is found in the recently developed eutectic HEAs (EHEAs), which borrow the concept of using lamellar structures as in-situ composites to balance mechanical properties. The first such alloy, AlCoCrFeNi2.1, with an FCC(L12) + BCC(B2) lamellar microstructure, remains the most studied EHEA. Despite much work put into its characterization, much remains to be understood. For example, more efforts have been given to optimize the mechanical properties while less are given to quantitatively describe the microstructure. Various thermo-mechanical treatments have been used to modify the mechanical properties of the AlCoCrFeNi2.1 alloy, however, previous studies mainly focused on the fully recrystallized materials, while a clear understanding of the recrystallization process is still missing, and the potential of partial recrystallization remains to be explored. The first part of this thesis work focuses on the as-cast microstructures of the eutectic and near-eutectic compositions of the AlCoCrFeNi2.1 system. Quantification of the phase volume and lamellar spacing is performed as a function of the Ni content. Orientation relationship and misorientation angle-axis changes in the five investigated alloys are also studied, with the previously unknown dependency of misorientation angle on the Ni content revealed. Some attention is also given to irregular microstructures in eutectic and near-eutectic compositions, which have not been discussed in previous studies. In the second part of this thesis work, a systematic study of the recrystallization process and the correlation between microstructure and mechanical properties in the thermo-mechanically treated AlCoCrFeNi2.1 alloy is undertaken. Distinctive behavior of the constituent phases during recrystallization, with varying rates of recrystallization and grain growth are observed, providing new insights to the recrystallization process in this alloy. Furthermore, it is shown that by controlling the annealing temperature and time, hetero-deformation induced hardening could lead to abnormal hardening in the as-rolled alloy, providing a new strategy to achieve high-strength with acceptable ductility in EHEAs.
|
|
| 9. |
- Manchili, Swathi Kiranmayee, 1987, et al.
(författare)
-
Comparative study on the densification of chromium pre-alloyed powder metallurgy steel through nanopowder addition using design of experiments
- 2021
-
Ingår i: Results in Materials. - : Elsevier BV. - 2590-048X. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- There is a constant demand for high density press and sinter powder metallurgical components for automotiveapplications. Steel powder pre-alloyed with chromium is an attractive material for such applications, but newways to further increase the sinter density are required for successful processing of these powders to high density.Nanopowder could be used as a potential sintering aid in order to boost the densification of the steel powdercompact. In this study, steel powder pre-alloyed with chromium, without and with admixed nickel, is used as basepowder, to which nanopowder was added. Surface oxide removal, crucial for successful sintering of such mate-rials, was studied by thermogravimetry analysis in order to understand the influence of nanopowder addition onthe oxide reduction. Powder compacts containing nanopowder showed higher mass loss in comparison to the oneswithout nanopowder. Linear shrinkage obtained from dilatometric curves increased with the addition of nano-powder. To depict the influence of the critical parameters; sintering temperature, powder size, addition ofnanopowder and composition (with or without nickel), a design of experiment approach was applied. The criticalparameters were then adjusted at 2 different values (categorical parameters) and a‘full factorial design model’was used involving 16 experiments, with sinter density and hardness as output measures of the experimentsdetermined. The results were analyzed using polynomialfit to determine which of the parameter exerts themaximum influence. Presence of nickel increased the hardness whereas sintering temperature and presence ofnanopowder enhanced the sinter density. This led to the tentative design of optimum conditions that resulted inincrease in sinter density from 7.25 g/cm3(92.5% of the theoretical density) to 7.4 g/cm3(94% of the theoreticaldensity) with an addition of 5% nanopowder to Ni-containing grade when sintered at 1350 °C instead of 1250 °C.
|
|
| 10. |
- Aldén, R., et al.
(författare)
-
Robustness of the HFMI techniques and the effect of weld quality on the fatigue life improvement of welded joints
- 2020
-
Ingår i: Welding in the World. - : Springer Science and Business Media Deutschland GmbH. - 0043-2288 .- 1878-6669. ; 64:11, s. 1947-1956
-
Tidskriftsartikel (refereegranskat)abstract
- Robustness of HFMI treatment in different weld qualities according to ISO 5817 was studied, and fatigue testing of the treated samples was carried out in order to investigate the effect of the weld quality prior treatment. The results show that HFMI-treated welds with weld quality level D shows fatigue life improvements that fall within the IIW recommendations for HFMI. No significant influence from the HFMI operator or HFMI equipment on the fatigue life was found. However, the scatter in fatigue testing results varied with HFMI operator and indicated that different HFMI operators could produce consistent treatment results. A considerable effect on fatigue life from HFMI tool radius was found, where the 2-mm tool radius showed considerably greater fatigue life compared with the 1.5-mm tool radius. According to IIW (Marquis and Barsoum 2016), for steel grade SY = 700 MPa, the fatigue strength recommendation is FAT 160 (m = 5) for transverse stiffener–welded joints with as-welded quality B according to ISO 5817 (ISO/TC 44/SC 10 2011), prior to treatment. It can be observed in the current study that fatigue-tested HFMI-treated welded joints, welded with weld quality D, are in good agreement with the IIW recommendations.
|
|
