Sökning: id:"swepub:oai:DiVA.org:hv-4686" >
Cutter Exit Effects...
Cutter Exit Effects during Milling of Thin-walled Inconel 718
-
- Wanner, Bertil, 1963- (författare)
- Högskolan Väst,Avd för maskinteknik,PTW,University West, Trollhättan, Sweden
-
- Eynian, Mahdi, 1980- (författare)
- Högskolan Väst,Avd för maskinteknik,Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),PTW,University West, Trollhättan, Sweden
-
- Beno, Tomas (författare)
- Högskolan Väst,Avd för maskinteknik,Avdelningen för avverkande och additativa tillverkningsprocesser (AAT),PTW,University West, Trollhättan, Sweden ; Volvo Aero Corporation, Trollhättan, Sweden
-
visa fler...
-
- Pejryd, Lars, 1955- (författare)
- Högskolan Väst,Avd för industriell produktion,PTW,University West, Trollhättan, Sweden ; Volvo Aero Corporation, Trollhättan, Sweden ; Production Technology Center, Innovatum AB, Trollhättan, Sweden
-
visa färre...
-
(creator_code:org_t)
- Trans Tech Publications Inc. 2012
- 2012
- Engelska.
-
Ingår i: Advanced Materials Research. - : Trans Tech Publications Inc.. - 1022-6680 .- 1662-8985. ; 590, s. 297-308, s. 297-308
- Relaterad länk:
-
http://www.scientifi...
-
visa fler...
-
https://urn.kb.se/re...
-
https://doi.org/10.4...
-
https://urn.kb.se/re...
-
https://urn.kb.se/re...
-
visa färre...
Abstract
Ämnesord
Stäng
- During milling of thin-walled components, chatter vibrations give rise to process issues. These include dimensional inaccuracy, damaged and scrap parts, and damaged cutting tools. This, in turn, leads to loss of production time with increasing cost as a consequence. This paper identifies the force profile during a single cut milling process. It focuses on the exit and post-exit behavior of the cut and discusses the process dynamics. The force profiles of various tool-to-workpiece positions are analyzed as regards the exit and post exit phases. A standard on-the-market cutter and a specially designed zero rake cutter are used in the investigation. Finally, a time-domain simulation of the force is performed and compared to the experimental results. The study concludes that a small change in exit angle may result in a considerable improvement in cutting behavior. In addition, the tool position should be chosen so that the cutter exits in the least flexible direction possible for the workpiece.
Ämnesord
- TEKNIK OCH TEKNOLOGIER -- Maskinteknik -- Produktionsteknik, arbetsvetenskap och ergonomi (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Mechanical Engineering -- Production Engineering, Human Work Science and Ergonomics (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Materialteknik -- Bearbetnings-, yt- och fogningsteknik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Materials Engineering -- Manufacturing, Surface and Joining Technology (hsv//eng)
Nyckelord
- Chatter vibrations
- Thin wall
- Inconel 718
- Process stability
- Exit angle
- Manufacturing and materials engineering
- Produktions- och materialteknik
Publikations- och innehållstyp
- ref (ämneskategori)
- art (ämneskategori)
Hitta via bibliotek
Till lärosätets databas