Tyck till om SwePub Sök
här!
Sökning: id:"swepub:oai:DiVA.org:ltu-91241" >
The effect of infil...
The effect of infill density on the fire properties of polylactic acid 3D printed parts: A short communication
-
- Mensah, Rhoda Afriyie (författare)
- Luleå tekniska universitet,Byggkonstruktion och brand,Luleå Univ Technol, Dept Civil Environm & Nat Resources Engn, Struct & Fire Engn Div, S-97187 Luleå, Sweden.
-
- Edström, David Aronsson (författare)
- Luleå tekniska universitet,Byggkonstruktion och brand,Luleå Univ Technol, Dept Civil Environm & Nat Resources Engn, Struct & Fire Engn Div, S-97187 Luleå, Sweden.
-
- Lundberg, Oskar (författare)
- Luleå tekniska universitet,Byggkonstruktion och brand,Luleå Univ Technol, Dept Civil Environm & Nat Resources Engn, Struct & Fire Engn Div, S-97187 Luleå, Sweden.
-
visa fler...
-
- Shanmugam, Vigneshwaran (författare)
- Luleå tekniska universitet,Byggkonstruktion och brand,Luleå Univ Technol, Dept Civil Environm & Nat Resources Engn, Struct & Fire Engn Div, S-97187 Luleå, Sweden.
-
- Jiang, Lin (författare)
- School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, 210094, China,Nanjing Univ Sci & Technol, Sch Mech Engn, Nanjing 210094, Peoples R China.
-
- Qiang, Xu (författare)
- School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, 210094, China,Nanjing Univ Sci & Technol, Sch Mech Engn, Nanjing 210094, Peoples R China.
-
- Försth, Michael (författare)
- Luleå tekniska universitet,Byggkonstruktion och brand,Luleå Univ Technol, Dept Civil Environm & Nat Resources Engn, Struct & Fire Engn Div, S-97187 Luleå, Sweden.
-
- Sas, Gabriel (författare)
- Luleå tekniska universitet,Byggkonstruktion och brand,Luleå Univ Technol, Dept Civil Environm & Nat Resources Engn, Struct & Fire Engn Div, S-97187 Luleå, Sweden.
-
- Hedenqvist, Mikael S. (författare)
- KTH,Polymera material,Department of Fibre and Polymer Technology, Polymeric Materials Division, School of Engineering Sciences in Chemistry, Biotechnology and Health, KTH Royal Institute of Technology, Stockholm, 100 44, Sweden
-
- Das, Oisik (författare)
- Luleå tekniska universitet,Byggkonstruktion och brand,Luleå Univ Technol, Dept Civil Environm & Nat Resources Engn, Struct & Fire Engn Div, S-97187 Luleå, Sweden.
-
visa färre...
-
(creator_code:org_t)
- Elsevier, 2022
- 2022
- Engelska.
-
Ingår i: Polymer testing. - : Elsevier. - 0142-9418 .- 1873-2348. ; 111
- Relaterad länk:
-
https://doi.org/10.1...
-
visa fler...
-
https://urn.kb.se/re...
-
https://doi.org/10.1...
-
https://urn.kb.se/re...
-
visa färre...
Abstract
Ämnesord
Stäng
- The use of 3D printing technology for manufacturing construction materials is gaining popularity, however, only a few studies have reported the fire behavior of such parts. In this research, the fire properties of 3D printed polylactide acid (PLA) parts with varying infill densities along with the tensile properties were analysed. The results from the fire tests showed that increasing the infill density increased the fuel load, which sustained combustion. Hence, the peak heat release rate and total heat release increased with an increment in infill density percentage. It was also observed that the increasing infill density had no effect on the flammability rating of the parts due to the constant shell thickness used for all the parts. In addition, the tensile strength and ductility of the parts increased with density as a porous part is more susceptible to failure than a solid homogeneous part.
Ämnesord
- NATURVETENSKAP -- Kemi -- Materialkemi (hsv//swe)
- NATURAL SCIENCES -- Chemical Sciences -- Materials Chemistry (hsv//eng)
- NATURVETENSKAP -- Fysik -- Annan fysik (hsv//swe)
- NATURAL SCIENCES -- Physical Sciences -- Other Physics Topics (hsv//eng)
- TEKNIK OCH TEKNOLOGIER -- Elektroteknik och elektronik -- Annan elektroteknik och elektronik (hsv//swe)
- ENGINEERING AND TECHNOLOGY -- Electrical Engineering, Electronic Engineering, Information Engineering -- Other Electrical Engineering, Electronic Engineering, Information Engineering (hsv//eng)
Nyckelord
- 3D printing
- Infill density
- Fire properties
- Byggkonstruktion
- Structural Engineering
Publikations- och innehållstyp
- ref (ämneskategori)
- art (ämneskategori)
Hitta via bibliotek
Till lärosätets databas
- Av författaren/redakt...
-
Mensah, Rhoda Af ...
-
Edström, David A ...
-
Lundberg, Oskar
-
Shanmugam, Vigne ...
-
Jiang, Lin
-
Qiang, Xu
-
visa fler...
-
Försth, Michael
-
Sas, Gabriel
-
Hedenqvist, Mika ...
-
Das, Oisik
-
visa färre...
- Om ämnet
-
- NATURVETENSKAP
-
NATURVETENSKAP
-
och Kemi
-
och Materialkemi
-
- NATURVETENSKAP
-
NATURVETENSKAP
-
och Fysik
-
och Annan fysik
-
- TEKNIK OCH TEKNOLOGIER
-
TEKNIK OCH TEKNO ...
-
och Elektroteknik oc ...
-
och Annan elektrotek ...
- Artiklar i publikationen
-
Polymer testing
- Av lärosätet
-
Luleå tekniska universitet
-
Kungliga Tekniska Högskolan