| 1. |
- Karlsson, Olov, et al.
(författare)
-
Presence of water-soluble compounds in thermally modified wood: Carbohydrates and furfurals
- 2012
-
Ingår i: BioResources. - 1930-2126 .- 1930-2126. ; 7:3, s. 3679-3689
-
Tidskriftsartikel (refereegranskat)abstract
- With thermal modification, changes in properties of wood, such as the presence of VOC and water-soluble carbohydrates, may occur. Thermal modifications under saturated steam conditions (160°C or 170°C) and superheated steam conditions (170, 185, and 212°C) were investigated by analysing the presence of water-soluble 5-(hydroxymethyl)furfural (HMF), furfural, and carbohydrates in heat-treated wood. The influence of thermal modifications on Scots pine, Norway spruce, and silver birch was also studied. Furfurals were analysed using HPLC at 280 nm, while monosaccharides and water-soluble carbohydrates were determined by GC-FID as their acetylated alditiols and, after methanolysis, as their trimethylsilylated methyl-glycosides, respectively. The amount of furfurals was larger in boards thermally modified under saturated steam conditions than those treated under superheated steam conditions. Generally, more of HMF than furfural was found in the thermally modified boards. In process water, in which saturated steam conditions had been used, furfural and only traces of HMF were found. Higher content of water-soluble carbohydrates was found in boards treated in saturated steam rather than in superheated steam. After modification in saturated steam, substantial parts of the water-soluble carbohydrates were due to monosaccharides, but only traces of monosaccharides were found in boards treated under superheated steam conditions.
|
|
| 2. |
- Karlsson, Olov, et al.
(författare)
-
Heat treatments of high temperature dried norway spruce boards: Saccharides and furfurals in sapwood surfaces
- 2012
-
Ingår i: BioResources. - : BioResources. - 1930-2126 .- 1930-2126. ; 7:2, s. 2284-2299
-
Tidskriftsartikel (refereegranskat)abstract
- Carbohydrates that migrate to wood surfaces in sapwood during drying might influence properties such as mould susceptibility and colour. Sugars on the surface of Norway spruce boards during various heat treatments were studied. Samples (350mm×125mm×25mm) were double-stacked, facing sapwood-side outwards, and dried at 110°C to a target moisture content (MC) of 40%. Dried sub-samples (80 mm × 125 mm × 25 mm) were stacked in a similar way and further heated at 110°C and at 130°C for 12, 24, and 36 hours, respectively. Glucose, fructose, and sucrose as well as 5-hydroxymethylfurfural (HMF) and furfural in the sapwood surface layer of treated wood were analysed using HPLC (RI- and UV-detectors). Carbohydrates degraded to a lower extent at 110°C than at 130°C. Furfural and to a larger extent HMF increased with treatment period and temperature. Heat treatment led to a decrease in lightness and hue of the sapwood surface of sub-samples, while chroma increased somewhat. Furthermore, considerably faster degradation (within a few minutes) of the carbohydrates on the surface of the dried spruce boards was observed when single sub-samples were conductively hot pressed at 200°C. Treatment period and initial MC influenced the presence of the carbohydrates in wood surface as well as colour change (ΔE ab) of the hot pressed sub-samples.
|
|
| 3. |
- Karlsson, Olov, et al.
(författare)
-
Influence of heat transferring media on durability of thermally modified wood
- 2011
-
Ingår i: BioResources. - : BioResources. - 1930-2126 .- 1930-2126. ; 6:1, s. 356-372
-
Tidskriftsartikel (refereegranskat)abstract
- Studies on the durability and dimensional stability of a series of hardwoods and softwoods after thermal modification in vegetable oils and in steam atmospheres have been performed. Mass loss after exposure to Coniophora puteana (BAM Ebw. 15) for 16 weeks was very low for European birch, European aspen, Norway spruce, and Scots pine thermally modified in a linseed oil product with preservative (for 1 hour at 200 degrees C). Fairly low mass losses were obtained for wood thermally modified in linseed-, tung-and rapeseed oil, and losses were related to the wood species. Low mass loss during rot test was also found for Norway spruce and Scots pine modified in saturated steam at 180 degrees C. Water absorption of pine and aspen was reduced by the thermal treatments and the extent of reduction was dependent on wood species and thermal modification method. Thermally modified aspen was stable during cycling climate tests, whereas pine showed considerable cracking when modified under superheated steam conditions (Thermo D). At lower modification temperature (180 degrees C) an increase in mass after modification in rapeseed oil of spruce, aspen and sapwood as well as heartwood of pine was observed, whereas at high temperature (240 degrees C) a mass loss could be found. Oil absorption in room tempered oil after thermal modification in oil was high for the more permeable aspen and pine (sapwood).
|
|
| 4. |
- Karlsson, Olov, et al.
(författare)
-
Colour stabilization of heat modified Norway spruce exposed to out-door conditions
- 2010
-
Ingår i: Proceedings, 11th International IUFRO Wood Drying Conference. - Luleå : Luleå tekniska universitet. ; , s. 265-268
-
Konferensbidrag (refereegranskat)abstract
- Wood boards from Norway spruce (300 mmx125mmx10mm) were heat modified in a pilot chamber corresponding to Thermowood-D quality. The surface of boards was sprayed with diluted solutions of ferrous sulphate alone or in combination with subsequent spraying of a 30% solution of hydrogen peroxide. The boards were exposed to outdoor conditions during summer 2009 (45o facing south). Colour coordinates were measured using a colorimeter.Only small changes in colour of boards were observed directly after the surface treatments. Lightness increased for boards with no surface treatments during out-door exposure (seven weeks). Increase in lightness was delayed when ferrous sulphate was applied to the board. Lightness was essentially unchanged during the out-door exposure period when ferrous sulphate and hydrogen peroxide was used to modify the wood surface (at low hydrogen peroxide charge a small increase of lightness was, however, observed). Chroma decreased for boards with surface treatments but levelled out after a couple of weeks. On the other hand a decrease in chroma of boards with no surface treatments started after about four weeks exposure. Hue increased for all the boards until the fourth week. After that hue of untreated boards and boards treated with both ferrous sulphate and hydrogen peroxide continue to increase.
|
|
| 5. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Uneven distribution of preservative in kiln-dried sapwood lumber of Scots pine : Impact of wood structure and resin allocation
- 2012
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 66:2, s. 251-258
-
Tidskriftsartikel (refereegranskat)abstract
- Scots pine (Pinus sylvestris L.) sapwood lumber was collected after kiln drying and preservative treatment with Celcure AC 800 (a copper-amine wood preservative). Distribution of the preservative throughout the lumber was visually examined. Not all, but some samples showed specific localized areas without any preservative distribution throughout their entire length. Those samples were assessed further for anatomical properties, specifically in impregnated and unimpregnated areas. Additional study was conducted on the morphological nature and redistribution of lipophilic extractives using three different histochemical staining methods. Intrinsic wood properties – especially the frequency of axial resin canals and the percentage of canals blocked – were found to be responsible for the irregular distribution of the preservative. Furthermore, the inability to create continuous and frequent interstitial spaces due to the collapse of thin-walled ray cells throughout the lumber resulted in un-even distribution of preservatives. Staining techniques were useful to localize places with more or less abundance of extractives (e.g., fats) in impregnated and unimpregnated wood, which varied considerably. Histochemical observations revealed information pertaining to the kiln dry specific distribution and redistribution of extractives between the areas. Moreover, resin reallocation and modification in ray parenchyma and resin canals induced by kiln drying would be another reason for the impregnation anomalies.
|
|
| 6. |
- Dagbro, Ola, et al.
(författare)
-
Colour responses from wood, thermally modified in superheated steam and pressurized steam atmospheres
- 2010
-
Ingår i: Wood Material Science & Engineering. - : Informa UK Limited. - 1748-0272 .- 1748-0280. ; 5:3, s. 211-219
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, two different methods were used to produce thermally modified wood. One was carried out in a typical kiln drying chamber using superheated steam (SS) and the other used pressurized steam in an autoclave cylinder (PS). Overall, both processes followed the same principles and the wood was not treated with any chemicals. Two wood species were studied, Scots pine (Pinus sylvestris) and Norway spruce (Picea abies). Treatments in the autoclave were carried out under pressure using temperatures of 160°C, 170°C and 180°C. Temperatures of 190°C and 212°C were used in treatments in the chamber at normal air pressure. The colour was measured using L*C*H colour space. Results for both species showed that similar L* (lightness) can be reached at lower (20-308C) temperatures using PS compared with SS treatment. The hue angle of PS-treated wood was smaller than that of SS-treated wood. No significant difference in C* (chroma) was detected. The difference in E value between PS- and SS-treated wood was smaller for Norway spruce than for Scots pine. The residual moisture content was about 10% higher in wood treated by the PS process compared with the SS process
|
|
| 7. |
- Glynn, James, et al.
(författare)
-
Economic Impacts of Future Changes in the Energy System : National Perspectives
- 2015
-
Ingår i: Informing Energy and Climate Policies Using Energy Systems Models. - Cham : Encyclopedia of Global Archaeology/Springer Verlag. - 9783319165394 - 9783319165400 ; , s. 359-387
-
Bokkapitel (refereegranskat)abstract
- In a climate constrained future, hybrid energy-economy model coupling gives additional insight into interregional competition, trade, industrial delocalisation and overall macroeconomic consequences of decarbonising the energy system. Decarbonising the energy system is critical in mitigating climate change. This chapter summarises modelling methodologies developed in the ETSAP community to assess economic impacts of decarbonising energy systems at a national level. The preceding chapter focuses on a global perspective. The modelling studies outlined here show that burden sharing rules and national revenue recycling schemes for carbon tax are critical for the long-term viability of economic growth and equitable engagement on combating climate change. Traditional computable general equilibrium models and energy systems models solved in isolation can misrepresent the long run carbon cost and underestimate the demand response caused by technological paradigm shifts in a decarbonised energy system. The approaches outlined within have guided the first evidence based decarbonisation legislation and continue to provide additional insights as increased sectoral disaggregation in hybrid modelling approaches is achieved
|
|
| 8. |
- Glynn, James, et al.
(författare)
-
Economic Impacts of Future Changes in the Energy System : Global Perspectives
- 2015
-
Ingår i: Informing Energy and Climate Policies Using Energy Systems Models. - Cham : Encyclopedia of Global Archaeology/Springer Verlag. - 9783319165394 - 9783319165400 ; , s. 333-358
-
Bokkapitel (refereegranskat)abstract
- In a climate constrained future, hybrid energy-economy model coupling gives additional insight into interregional competition, trade, industrial delocalisation and overall macroeconomic consequences of decarbonising the energy system. Decarbonising the energy system is critical in mitigating climate change. This chapter summarises modelling methodologies developed in the ETSAP community to assess economic impacts of decarbonising energy systems at a global level. The next chapter of this book focuses on a national perspective. The range of economic impacts is regionally dependent upon the stage of economic development, the level of industrialisation, energy intensity of exports, and competition effects due to rates of relative decarbonisation. Developed nation’s decarbonisation targets are estimated to result in a manageable GDP loss in the region of 2 % by 2050. Energy intensive export driven developing countries such as China and India, and fossil fuel exporting nations can expect significantly higher GDP loss of up to 5 % GDP per year by mid-century.
|
|
| 9. |
- Qian, Yang, et al.
(författare)
-
Dimensional Stability and Water Repellency of European Aspen Improved by Oxidized Carbohydrates.
- 2013
-
Ingår i: BioResources. - : University of North Carolina Press. - 1930-2126 .- 1930-2126. ; 8:1, s. 487-498
-
Tidskriftsartikel (refereegranskat)abstract
- Small samples from European aspen (Populus tremula L.) were impregnated with carbohydrates oxidized by Fenton's reagent using water in a vacuum, followed by heating in an oven at 103 °C. An antiswelling efficiency (ASE) of around 45% for wood treated with oxidized glucose and 35% for wood treated with oxidized sucrose was obtained. Samples treated with oxidized carbohydrates gave water repellent effectiveness (WRE) values over 35%. The decrease in cell wall thickness during impregnation was about 18% less in the presence of oxidized glucose than samples only treated with Fenton's reagent. An ASE of 20% for the wood samples that had been treated with oxidized glucose was obtained after 7 days of soaking in water. The reasons for the improvement in dimensional stability are discussed in this work.
|
|
| 10. |
- Sehlstedt-Persson, Margot, et al.
(författare)
-
Mold growth on sapwood boards exposed outdoors : the impact of wood drying
- 2011
-
Ingår i: Forest products journal. - : Forest Products Society. - 0015-7473. ; 61:2, s. 170-179
-
Tidskriftsartikel (refereegranskat)abstract
- Mold growth on dried Norway spruce and Scots pine sapwood boards was investigated in an accelerated outdoor field test for 96 days. The boards were dried using three different methods of stacking: single stacking, double stacking with the sapwood sides in each pair facing toward each other, and double stacking with sapwood sides facing outward. Drying was performed at three temperatures: 25ºC, corresponding to air drying, and kiln drying at 70ºC and 110ºC. The degree of mold growth was visually assessed on both sides of each board. On average, pine boards showed a higher level of mold growth than the spruce boards. The highest average level of mold growth was found on the boards kiln dried at 708C, whereas the air-dried boards and the boards kiln dried at 110ºC showed considerably less mold growth. Stacking the boards during drying had a large impact on mold susceptibility of the sapwood. This study confirmed that, during the drying process, it is possible to direct the migration of nutrients in sapwood toward one chosen side of each board by double stacking; the opposite side leaches out, which has a great impact on surface mold growth. Chemical analyses of monosaccharide sugar gradients beneath the boards’ surfaces confirmed the results.
|
|
