| 1. |
|
|
| 2. |
- Admassie, Shimelis, et al.
(författare)
-
Electrochemical and optical studies of the band gaps of alternating polyfluorene copolymers
- 2006
-
Ingår i: Synthetic metals. - : Elsevier BV. - 0379-6779 .- 1879-3290. ; 156:7-8, s. 614-623
-
Tidskriftsartikel (refereegranskat)abstract
- The electrochemical and optical properties of a series of alternating polyfluorene copolymers with low band gaps were determined. These polymers incorporated fluorene units alternating with groups including electron-withdrawing (A) and electron-donating (D) groups in donor-acceptor-donor (DAD) sequence to achieve the lowering of band gaps. The polymers were solvent-casted on platinum disk electrode and the band gaps were estimated from cyclic voltammetry (CV). These values were compared with values obtained from optical absorption measurements. Although the electrochemically determined band gaps were found to be slightly higher than the optical band gap in most cases, values are well correlated. The values of the band gaps determined range from 2.1 to 1.3 eV. © 2006 Elsevier B.V. All rights reserved.
|
|
| 3. |
|
|
| 4. |
- Bjorstrom, Cecilia M., et al.
(författare)
-
Influence of solvents and substrates on the morphology and the performance of low-bandgap polyfluorene: PCBM photovoltaic devices - art. no. 61921X
- 2006
-
Ingår i: Proceedings of SPIE, the International Society for Optical Engineering. - : International Society for Optical Engineering; 1999. - 0277-786X .- 1996-756X. ; 6192, s. X1921-X1921
-
Tidskriftsartikel (refereegranskat)abstract
- Spin-coated thin films of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4,7-di-2-thienyl-2,1,3-benzothiadiazole)] (APFO-3) blended with [6,6]-phenyl-C-61-butyric acid methyl ester (PCBM) are used as the active material in polymer photovoltaic cells. Such blends are known for their tendency to phase separate during film formation. Tuning the morphology of the blend in a controlled way is one possible road towards higher efficiency. We studied the effect of adding chlorobenzene to chloroform-based blend solutions before spin-coating on the conversion efficiency of APFO-3:PCBM photodiodes, and related that to the lateral and vertical morphology of thin films of the blend. The lateral morphology is imaged by atomic force microscopy (AFM) and the vertical compositional profile is obtained by dynamic secondary ion mass spectrometry (SIMS). The profiles reveal compositional variations consisting of multilayers of alternating polymer-rich and PCBM-rich domains in the blend film spin-coated from chloroform. The vertical compositional variations are caused by surface-directed spinodal waves and are frozen in during the rapid evaporation of a highly volatile solvent. With addition of the low-vapour pressure solvent chlorobenzene, a more homogeneous vertical composition is found. The conversion efficiency for solar cells of this blend was found to be optimal for chloroform: chlorobenzene mixtures with a volume-ratio of 80:1. We have also investigated the role of the substrate on the morphology. We found that blend films spin-coated from chloroform solutions on PEDOT:PSS-coated ITO show a similar compositional structure as the films on silicon, and that changing the substrate from silicon to gold only affects the vertical phase separation in a region close to the substrate interface.
|
|
| 5. |
- Björström, Cecilia M., et al.
(författare)
-
Influence of solvents and substrates on the morphology and the performance of low-bandgap polyfluorene:PCBM photovoltaic devices
- 2006
-
Ingår i: Proceedings of SPIE, the International Society for Optical Engineering. - Cardiff : SPIE - International Society for Optical Engineering. - 0277-786X .- 1996-756X. ; 6192, s. 61921X-
-
Tidskriftsartikel (refereegranskat)abstract
- Spin-coated thin films of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (APFO-3) blended with [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) are used as the active material in polymer photovoltaic cells. Such blends are known for their tendency to phase separate during film formation. Tuning the morphology of the blend in a controlled way is one possible road towards higher efficiency. We studied the effect of adding chlorobenzene to chloroform-based blend solutions before spin-coating on the conversion efficiency of APFO-3:PCBM photodiodes, and related that to the lateral and vertical morphology of thin films of the blend. The lateral morphology is imaged by atomic force microscopy (AFM) and the vertical compositional profile is obtained by dynamic secondary ion mass spectrometry (SIMS). The profiles reveal compositional variations consisting of multilayers of alternating polymer-rich and PCBM-rich domains in the blend film spin-coated from chloroform. The vertical compositional variations are caused by surface-directed spinodal waves and are frozen in during the rapid evaporation of a highly volatile solvent. With addition of the low-vapour pressure solvent chlorobenzene, a more homogeneous vertical composition is found. The conversion efficiency for solar cells of this blend was found to be optimal for chloroform:chlorobenzene mixtures with a volume-ratio of 80:1. We have also investigated the role of the substrate on the morphology. We found that blend films spin-coated from chloroform solutions on PEDOT:PSS-coated ITO show a similar compositional structure as the films on silicon, and that changing the substrate from silicon to gold only affects the vertical phase separation in a region close to the substrate interface
|
|
| 6. |
- Gadisa, Abay, et al.
(författare)
-
Stoichiometry dependence of charge transport in polymer/methanofullerene and polymer/C70 derivative based solar cells
- 2006
-
Ingår i: Organic electronics. - : Elsevier BV. - 1566-1199. ; 7:4, s. 195-204
-
Tidskriftsartikel (refereegranskat)abstract
- Charge transport in a near infrared absorbing polyfluorene copolymer (APFO-Green1) and its blends with methanofullerene [6,6]-phenyl C61-butyric acid methyl ester (PCBM), and 3′-(3,5-bis-trifluoromethylphenyl)-1′-(4-nitrophenyl)pyrazolino[70]fullerene (BTPF70) is reported. PCBM and BTPF70 are electron acceptor and transporting molecules in polymer based solar cells. The BTPF70 has emerged as a new electron acceptor molecule that provides adequate exciton dissociation when blended with the low band gap polyfluorene copolymer APFO-Green1. Electron transport in both net PCBM and BTPF70 films are subjected to positional and energetic disorder, with the degree of disorder being more pronounced in BTPF70. On the other hand, mixing PCBM with conjugated polymers usually leads to increased hole mobility. We have investigated and compared the acceptor concentration dependence of charge transport in APFO-Green1/PCBM and APFO-Green1/BTPF70 blend films. For better understanding of the charge transport in the heterojunction films, the field and temperature dependence of hole transport in pure APFO-Green1 films has also been studied. It is observed that the behavior of hole mobility in the blend layer is sensitive to the acceptor type. For APFO-Green1/PCBM hole only devices, the hole mobility attains a local maximum at 67 wt.% of PCBM, while on the contrary mixing any amount of BTPF70 with APFO-Green1 results into degradation of hole transport. Electron transport in both blends, however, increases monotonically as a function of acceptor loading.
|
|
| 7. |
- Gadisa, Abay, et al.
(författare)
-
Transparent polymer cathode for organic photovoltaic devices
- 2006
-
Ingår i: Synthetic metals. - : Elsevier BV. - 0379-6779 .- 1879-3290. ; 156:16-17, s. 1102-1107
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate a prototype solar cell with a transparent polymer cathode, and indium-tin-oxide (ITO)/poly (3, 4-ethylene dioxythiophene)-poly (styrene sulphonate) (PEDOT:PSS) anode. As an active layer, thin film of a bulk heterojunction of polyfluorene copolymer poly[2,7-(9,9-dioctyl-fluorene)-alt-5,5-(4′,7′-di-2thienyl-2′,1′3′-benzothiadiazole)] (APFO-3) and an electron acceptor molecule [6] and [6]-phenyl-C61-butyric acid methyl ester (PCBM) (1:4 wt.) was sandwiched between the two transparent polymer electrodes. The cathode is another form of PEDOT formed by vapor phase polymerised PEDOT (VPP PEDOT) of conductivity 102–103 S/cm. The cathode is supported on an elastomeric substrate, and forms a conformal contact to the APFO-3/PCBM blend. Transparent solar cells are useful for building multilayer and tandem solar cells.
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
|
|
