| 1. |
- Azad, AK, et al.
(författare)
-
Preparation, Crystal and Magnetic Structure of the Double Perovskite Ba2FeWO6
- 2002
-
Ingår i: Applied Physics A. - : Springer Science and Business Media LLC. ; A 74, s. S763-765
-
Tidskriftsartikel (refereegranskat)abstract
- Single-phase polycrystalline material of the double perovskite Ba2FeWO6 was prepared and characterized by X-ray and neutron powder diffraction (NPD). The crystal structure was tetragonal with lattice parameters a=b=5.7479(4) Å and c=8.1444(9) Å at room temperature (295 K). NPD data at 10 K shows the evidence of an antiferromagnetic ordering of the Fe atoms. The reverse Monte Carlo powder (RMCPOW) technique was used to find the magnetic structure, which showed that it is based on a unit cell related to that of the nuclear structure by the propagation vector 0 \frac[¯]1[¯][¯]2[¯] \frac[¯]1[¯][¯]2[¯] . An ordering of collinear spins was found with alternate layers in the c-direction or in the a-b plane. The model was checked by Rietveld refinement and the magnetic moment of iron was found to be 3.39(2)7B at 10 K.
|
|
| 2. |
- Bahaloo, Hassan, et al.
(författare)
-
Mapping of density-dependent material properties of dry manufactured snow using μCT
- 2024
-
Ingår i: Applied Physics A. - : Springer Nature. - 0947-8396 .- 1432-0630. ; 130
-
Tidskriftsartikel (refereegranskat)abstract
- Despite the significance of snow in various cryospheric, polar, and construction contexts, more comprehensive studies are required on its mechanical properties. In recent years, the utilization of μ CT has yielded valuable insights into snow analysis. Our objective is to establish a methodology for mapping density-dependent material properties for dry manufactured snow within the density range of 400–600 kg/m 3 utilizing μ CT imaging and step-wise, quasi-static, mechanical loading. We also aim to investigate the variations in the structural parameters of snow during loading. The three-dimensional (3D) structure of snow is captured using μ CT with 801 projections at the beginning of the experiments and at the end of each loading step. The sample is compressed at a temperature of − 18 o C using a constant rate of deformation (0.2 mm/min) in multiple steps. The relative density of the snow is determined at each load step using binary image segmentation. It varies from 0.44 in the beginning to nearly 0.65 at the end of the loading, which corresponds to a density range of 400–600 kg/m 3 . The estimated modulus and viscosity terms, obtained from the Burger’s model, show an increasing trend with density. The values of the Maxwell and Kelvin–Voigt moduli were found to range from 60 to 320 MPa and from 6 to 40 MPa, respectively. Meanwhile, the viscosity values for the Maxwell and Kelvin–Voigt models varied from 0.4 to 3.5 GPa-s, and 0.3–3.2 GPa-s, respectively, within the considered density range. In addition, Digital Volume Correlation (DVC) was used to calculate the full-field strain distribution in the specimen at each load step. The image analysis results show that, the particle size and specific surface area (SSA) do not change significantly within the studied range of loading and densities, while the sphericity of the particles is increased. The grain diameter ranges from approximately 100 μ m to nearly 400 μ m, with a mode of nearly 200 μ m. The methodology presented in this study opens up a path for an extensive statistical analysis of the material properties by experimenting more snow samples.
|
|
| 3. |
- Bahaloohoreh, Hassan, 1983-, et al.
(författare)
-
Material mapping strategy to identify the density-dependent properties of dry natural snow
- 2024
-
Ingår i: Applied Physics A. - : Springer Nature. - 0947-8396 .- 1432-0630. ; 130:2
-
Tidskriftsartikel (refereegranskat)abstract
- The mechanical properties of natural snow play a crucial role in understanding glaciers, avalanches, polar regions, and snow-related constructions. Research has concentrated on how the mechanical properties of snow vary, primarily with its density; the integration of cutting-edge techniques like micro-tomography with traditional loading methods can enhance our comprehension of these properties in natural snow. This study employs CT imaging and uniaxial compression tests, along with the Digital Volume Correlation (DVC) to investigate the density-dependent material properties of natural snow. The data from two snow samples, one initially non-compressed (test 1) and the other initially compressed (test 2), were fed into Burger’s viscoelastic model to estimate the material properties. CT imaging with 801 projections captures the three-dimensional structure of the snow initially and after each loading step at -18C, using a constant deformation rate (0.2 mm/min). The relative density of the snow, ranging from 0.175 to 0.39 (equivalent to 160–360 kg/m), is determined at each load step through binary image segmentation. Modulus and viscosity terms, estimated from Burger’s model, exhibit a density-dependent increase. Maxwell and Kelvin–Voigt moduli range from 0.5 to 14 MPa and 0.1 to 0.8 MPa, respectively. Viscosity values for the Maxwell and Kelvin–Voigt models vary from 0.2 to 2.9 GPa-s and 0.2 to 2.3 GPa-s within the considered density range, showing an exponent between 3 and 4 when represented as power functions. Initial grain characteristics for tests 1 and 2, obtained through image segmentation, reveal an average Specific Surface Area (SSA) of around 55 1/mm and 40 1/mm, respectively. The full-field strain distribution in the specimen at each load step is calculated using the DVC, highlighting strong strain localization indicative of non-homogeneous behavior in natural snow. These findings not only contribute to our understanding of natural snow mechanics but also hold implications for applications in fields such as glacier dynamics and avalanche prediction.
|
|
| 4. |
- Bano, Nargis, et al.
(författare)
-
Study of Au/ZnO nanorods Schottky light-emitting diodes grown by low-temperature aqueous chemical method
- 2010
-
Ingår i: Applied Physics A. - : Springer Science Business Media. - 0947-8396 .- 1432-0630. ; 100:2, s. 467-472
-
Tidskriftsartikel (refereegranskat)abstract
- High quality vertically aligned ZnO nanorods (NRs) were grown by low-temperature aqueous chemical technique on 4H-n-SiC substrates. Schottky light-emitting diodes (LEDs) were fabricated. The current-voltage (I-V) characteristics of Schottky diodes reveal good rectifying behavior. Optical properties of the ZnO nanorods (NRs) were probed by cathodoluminescence (CL) measurements at room temperature complemented with electroluminescence (EL). The room-temperature CL spectra of the ZnO NRs exhibit near band edge (NBE) emission as well as strong deep level emission (DLE) centered at 690 nm. At room temperature the CL spectra intensity of the DLE was enhanced with the increase of the electron beam penetration depth due to the increase of defect concentration at the interface and due to the conversion of self-absorbed UV emission. We observed a variation in the DLE along the nanorod depth. This indicates a relatively lower structural quality near the interface between ZnO NRs and n-SiC substrate. The room-temperature CL spectra of SiC show very weak emission, which confirms that most of the DLE is originating from the ZnO NRs, and SiC has a minute contribution to the emission.
|
|
| 5. |
- Baranowski, M., et al.
(författare)
-
Nitrogen-related changes in exciton localization and dynamics in GaInNAs/GaAs quantum wells grown by metalorganic vapor phase epitaxy
- 2015
-
Ingår i: Applied Physics A. - : Springer Science and Business Media LLC. - 0947-8396 .- 1432-0630. ; 118:2, s. 479-486
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, we show the results of low-temperature photoluminescence (PL), time-resolved photoluminescence, and photoreflectance (PR) investigations, performed on a series of three Ga0.64In0.34As1-x N (x) /GaAs single quantum wells (SQW) grown by metalorganic vapor phase epitaxy with the nitrogen content of 0, 0.5, and 0.8 %. Comparing the PL and PR data, we show that at low excitation intensity and temperature, the radiative recombination occurs via localizing centers (LCs) in all samples. The excitation intensity-dependent PL measurements combined with theoretical modeling of hopping excitons in this system allow us to provide quantitative information on the disorder parameters describing population of LCs. It has been found that the average energy of LCs increases about two times and simultaneously the number of LCs increases about 10 and 20 times after the incorporation of 0.5 and 0.8 % of nitrogen, respectively. The value of average localization energy E > (0) determined for N-containing samples (similar to 6-7 meV) is in the range typical for dilute nitride QWs grown by molecular beam epitaxy (MBE). On the other hand, the "effective" concentration of LCs seems to be higher than for GaInNAs/GaAs QW grown by MBE. The dramatic increase in localizing centers also affects the PL dynamics. Observed PL decay time dispersion is much stronger in GaInNAs SQW than in nitrogen-free SQW. The change in PL dynamic is very well reproduced by model of hopping excitons.
|
|
| 6. |
- Batvandi, Mohammadreza, et al.
(författare)
-
Visible-light-driven photocatalysis with Z-scheme Ag3PO4@N-GQDs@g-C3N4 nano/hetero-junctions
- 2022
-
Ingår i: Applied Physics A. - : Springer Nature. - 0947-8396 .- 1432-0630. ; 128:10
-
Tidskriftsartikel (refereegranskat)abstract
- The fabrication and improved performance of Z-scheme visible-light-driven Ag3PO4@N-GQDs@g-C3N4 ternary nano/hetero-junctions have been described in this study. Fern-like silver orthophosphate (Ag3PO4) microstructures have been modified using nitrogen-doped graphene quantum dots (N-GQDs) and then have been coated by ultrathin graphitic carbon nitride (g-C3N4) sheets via a combined technique including freeze-drying and refluxing methods. Photocatalytic studies have been conducted through visible-light photo-degradation of standard methylene blue dye in aqueous media. The Ag3PO4@N-GQDs@g-C3N4 ternary nano/hetero-junctions have exhibited the promoted photocatalytic efficiency of 97.91%, which is about 1.07 and 1.34 times higher than that of Ag3PO4@g-C3N4 binary nano/hetero-junctions (91.46%) and pristine-Ag3PO4 microstructures (85.91%), respectively. The excellent recyclability of the Ag3PO4@N-GQDs@g-C3N4 photo-catalyst has been verified in the cycle operations in which the recycling efficiency could have been maintained at 94.92% after five runs of experiments. The quenching effects of scavengers have suggested that the superoxide radicals (O-2(-center dot)) and holes (h(+)) are the predominant active species governing the photocatalytic reaction of the Ag3PO4@N-GQDs@g-C3N4 ternary composite due to a Z-scheme junction. The improved photocatalytic activity of Ag3PO4@N-GQDs@g-C3N4 nano/hetero-junctions could have been ascribed to the higher visible-light harvesting capacity, better charge carrier separation and stronger oxidation and reduction ability relevant to the indirect Z-scheme system where N-GQDs act as an efficient electron transfer media.
|
|
| 7. |
- Bhatt, Pramod, et al.
(författare)
-
Electronic structure of thin film iron-tetracyanoethylene : Fe(TCNE)x
- 2009
-
Ingår i: Applied Physics A. - : Springer Science and Business Media LLC. - 0947-8396 .- 1432-0630. ; 95:1, s. 131-138
-
Tidskriftsartikel (refereegranskat)abstract
- Thin film iron-tetracyanoethylene Fe(TCNE) x , x∼2, as determined by photoelectron spectroscopy, was grown in situ under ultra-high vacuum conditions using a recently developed physical vapor deposition-based technique for fabrication of oxygen- and precursor-free organic-based molecular magnets. Photoelectron spectroscopy results show no spurious trace elements in the films, and the iron is of Fe2+ valency. The highest occupied molecular orbital of Fe(TCNE) x is located at ∼1.7 eV vs. Fermi level and is derived mainly from the TCNE− singly occupied molecular orbital according to photoelectron spectroscopy and resonant photoelectron spectroscopy results. The Fe(3d)-derived states appear at higher binding energy, ∼4.5 eV, which is in contrast to V(TCNE)2 where the highest occupied molecular orbital is mainly derived from V(3d) states. Fitting ligand field multiplet and charge transfer multiplet calculations to the Fe L-edge near edge X-ray absorption fine structure spectrum yields a high-spin Fe2+ (3d6) configuration with a crystal field parameter 10Dq∼0.6 eV for the Fe(TCNE) x system. We propose that the significantly weaker Fe-TCNE ligand interaction as compared to the room temperature magnet V(TCNE)2 (10Dq∼2.3 eV) is a strongly contributing factor to the substantially lower magnetic ordering temperature (T C ) seen for Fe(TCNE) x -type magnets.
|
|
| 8. |
- Blomqvist, M., et al.
(författare)
-
Structural and tribological properties of cluster-assembled CNx films
- 2007
-
Ingår i: Applied Physics A. - : Springer Science and Business Media LLC. - 0947-8396 .- 1432-0630. ; 87:4, s. 767-772
-
Tidskriftsartikel (refereegranskat)abstract
- We report the structural and tribological characterization of nanostructured CNx thin films produced by the deposition of a supersonic carbon cluster beam assisted by nitrogen ion bombardment. The influence of the deposition parameters on the chemical composition and structure of the films has been systematically studied by X-ray photoelectron spectroscopy, elastic recoil detection analysis, transmission electron microscopy and atomic force microscopy. Depending on the deposition parameters, the films show a structure ranging from amorphous to disordered graphitic with interlinked planes. Nitrogen content depends on the nitrogen ion kinetic energy. The films have a very low density with a high surface roughness. Friction measurements at the nanoscale show a correlation between nitrogen content and mechanical properties of the system.
|
|
| 9. |
- Bulgakov, Alexander, 1956, et al.
(författare)
-
Phosphorus cluster production by laser ablation
- 2004
-
Ingår i: Applied Physics A. - : Springer Science and Business Media LLC. - 0947-8396 .- 1432-0630. ; 79, s. 1369-1372
-
Tidskriftsartikel (refereegranskat)abstract
- Neutral and charged phosphorus clusters of a wide size range have been produced by pulsed laser ablation (PLA) in vacuum at 532, 337, and 193 nm ablating wavelengths and investigated by time-of-flight mass spectrometry. The neutral Pn clusters are even-numbered with local abundance maxima at n=10 and 14, while the cationic and anionic clusters are preferentially odd-numbered with P7+, P21+, and P17- being the most abundant ions. The dominance of the magic clusters is more pronounced at 337-nm ablation that is explained by efficient direct ejection of their building blocks under these conditions. Nanocrystalline phosphorus films have been produced by PLA in ambient helium gas.
|
|
| 10. |
- Bulgakova, Nadya, 1956, et al.
(författare)
-
A general continuum approach to describe fast electronic transport in pulsed laser irradiated materials: the problem of Coulomb explosion
- 2005
-
Ingår i: Applied Physics A. - : Springer Science and Business Media LLC. - 0947-8396 .- 1432-0630. ; 81, s. 345-356
-
Tidskriftsartikel (refereegranskat)abstract
- We present a continuum model, based on a drift-diffusion approach, aimed at describing the dynamics of electronic excitation, heating, and charge-carrier transport in different materials (metals, semiconductors, and dielectrics) under femtosecond and nanosecond pulsed laser irradiation. The laser-induced charging of the targets is investigated at laser intensities above the material removal threshold. It is demonstrated that, for near-infrared femtosecond irradiation, charging of dielectric surfaces causes a sub-picosecond electrostatic rupture of the superficial layers, alternatively called Coulomb explosion (CE), while this effect is strongly inhibited for metals and semiconductors as a consequence of superior carrier transport properties. On the other hand, application of the model to UV nanosecond pulsed laser interaction with bulk silicon has pointed out the possibility of Coulomb explosion in semiconductors. For such regimes a simple analytical theory for the threshold laser fluence of CE has been developed, showing results in agreement with the experimental observations. Various related aspects concerning the possibility of CE depending on different irradiation parameters (fluence, wavelength and pulse duration) and material properties are discussed. This includes the temporal and spatial dynamics of charge-carrier generation in non-metallic targets and evolution of the reflection and absorption characteristics.
|
|
