| 1. |
- Abdel Hady, Ahmed Wagih Abdallah, 1990, et al.
(författare)
-
In situ microstructural evolution of spruce wood during soda pulping using synchrotron X-ray tomography
- 2022
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 76:7, s. 611-621
-
Tidskriftsartikel (refereegranskat)abstract
- A new laboratory reactor to perform in situ studies of structural changes in wood during soda pulping using synchrotron X-ray tomography is presented. The reactor is of recirculation type to provide stable reaction conditions and mimic the industrial situation. Experiments have been performed using this reactor in situ at a synchrotron microtomography beamline to provide sequences of 3D images from which measurement of wood cell wall thickness have been possible for the first time. The results showed that the cell wall thickness increased significantly in the early stage of pulping (<10 min), which is due to the transportation of cooking chemicals through the tracheids, resin channels and pits into the cell wall, which is swollen with the increased pH. Subsequently, the cell wall thickness reduces over the processing time up to 60 min with a high rate, which is inferred to be due to the dissolution and transport of lignin and hemicellulose from the secondary walls, allowing for better transportation of active chemicals deep through the cell wall layers. After 60 min processing, the cell wall thickness reduction rate reduced, as dissolution of lignin and hemicelluloses from the cell walls ceased, while the remaining dissolution occurs mainly at the middle lamella.
|
|
| 2. |
- Abdel Hady, Ahmed Wagih Abdallah, 1990, et al.
(författare)
-
Micro/nano-structural evolution in spruce wood during soda pulping
- 2021
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 75:8, s. 754-764
-
Tidskriftsartikel (refereegranskat)abstract
- Alkaline delignification of wood tissue is the core of the global pulping technology and the most prominent large-scale separation of the main wood components. This work aims at improved understanding of the interplay between the topochemistry of alkaline pulping and the associated morphological changes. Morphology and chemical structure of partially soda-delignified wood chips were studied combining X-ray tomography (XRT), X-ray diffraction analysis and compositional characterization (lignin and carbohydrate content). The XRT studies of wet samples (providing 3D structural information without interfering drying effects), allowed observation of the cell wall separation as an increasing amount of lignin was removed with the increasing pulping time. Comparison between the microstructure of the surface and the central parts of the treated chips showed a more delignified microstructure at the surface, which highlights the dependence of the delignification process on the mass transport (hydroxide ions and lignin fragments) through the wood tissue. The crystallite size of cellulose increased in the <200> crystal planes during the early stage of pulping while there was little effect on the <110> plane.
|
|
| 3. |
- Adamopoulos, Stergios, et al.
(författare)
-
Tensile strength of handsheets prepared with macerated fibres from solid wood modified with cross-linking agents
- 2015
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 69:8, s. 959-966
-
Tidskriftsartikel (refereegranskat)abstract
- This study was conducted to explain the tensile strength loss of wood due to the modification with 1,3-dimethylol-4,5-dihydroxyethyleneurea (DMDHEU) and glutaraldehyde (GA). Modified and control wood blocks were macerated to deliberate fibres, and handsheets were produced thereof. The nitrogen content of the fibres indicated that maceration removed the major proportions of DMDHEU. The stability of GA in wood during maceration was not assessed. Tensile strength determined at zero span (z-strength) and finite span (f-strength) was equal for the handsheets from DMDHEU-modified fibres and the control handsheets. The microscopic appearance of the tested finite-span paper strips from DMDHEU-modified fibres mainly indicated interfibre failure and did not differ from the fibre fracture mode of the control handsheets. In contrast, the z-strength of the handsheets from GA-modified fibres was lower than that of controls and decreased with increasing content of GA in the initial modified wood. The f-strength behaviour of the handsheets from GA-modified fibres was the opposite: it was higher than that of controls and increased with increasing GA content. The microscopic appearance of the rapture zones of the finite-span testing mainly indicated intrafibre failure for the GA-modified fibres. It was concluded that cross-linking is likely to be the major reason for tensile strength loss of GA- and DMDHEU-modified wood. In terms of DMDHEU-modified wood, the incrustation of the cell wall by the resin and the reduction in pliability could play an additional role.
|
|
| 4. |
- Ahlbom, Anders, 1993, et al.
(författare)
-
On the hydrothermal depolymerisation of kraft lignin using glycerol as a capping agent
- 2023
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 77:3, s. 159-169
-
Tidskriftsartikel (refereegranskat)abstract
- Depolymerisation of kraft lignin under hydrothermal conditions was investigated at short residence times (1–12 min) with glycerol being used as a capping agent. The weight average molecular weight (M w) of the products decreased within the first minute of residence time, with the inter-unit ether linkages breaking accordingly. Furthermore, the M w of the product fractions decreased at increasing residence times, while the char yield increased. Short residence times thus appear to be beneficial for mitigating the formation of char. Also, addition of NaOH reduced the yield of char. Although the addition of glycerol caused a decrease in the M w of the products, it seemed to increase the yield of char and therefore might not be a suitable capping agent for kraft lignin depolymerisation.
|
|
| 5. |
- Ahlbom, Anders, 1993, et al.
(författare)
-
Towards understanding kraft lignin depolymerisation under hydrothermal conditions
- 2021
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 76:1, s. 37-48
-
Tidskriftsartikel (refereegranskat)abstract
- Kraft lignin depolymerisation using hydrothermal liquefaction suffers from the formation of char, resulting in a decreased product yield as well as causing operational problems. While this may be mitigated by the addition of capping agents such as phenol and isopropanol, other reaction parameters, for example reaction time and temperature, are also important for the product yields. In this work, the effect of short reaction times on the hydrothermal liquefaction of kraft lignin in an alkaline water and isopropanol mixture was investigated at 1-12 min and 290 °C. The results show that there were swift initial reactions: the major ether bonds in the lignin were broken within the first minute of reaction, and the molecular weight of all product fractions was halved at the very least. Longer reaction times, however, do not cause as pronounced structural changes as the initial reaction, indicating that a recalcitrant carbon-carbon skeleton remained in the products. Nevertheless, the yields of both char and monomers increased slowly with increasing reaction time. The swift initial depolymerising reactions were therefore followed by slower repolymerisation as well as a slow formation of monomers and dimers, which calls for careful tuning of the reaction time.
|
|
| 6. |
- Ahmed, Sheikh Ali, et al.
(författare)
-
Uneven distribution of preservative in kiln-dried sapwood lumber of Scots pine : Impact of wood structure and resin allocation
- 2012
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 66:2, s. 251-258
-
Tidskriftsartikel (refereegranskat)abstract
- Scots pine (Pinus sylvestris L.) sapwood lumber was collected after kiln drying and preservative treatment with Celcure AC 800 (a copper-amine wood preservative). Distribution of the preservative throughout the lumber was visually examined. Not all, but some samples showed specific localized areas without any preservative distribution throughout their entire length. Those samples were assessed further for anatomical properties, specifically in impregnated and unimpregnated areas. Additional study was conducted on the morphological nature and redistribution of lipophilic extractives using three different histochemical staining methods. Intrinsic wood properties – especially the frequency of axial resin canals and the percentage of canals blocked – were found to be responsible for the irregular distribution of the preservative. Furthermore, the inability to create continuous and frequent interstitial spaces due to the collapse of thin-walled ray cells throughout the lumber resulted in un-even distribution of preservatives. Staining techniques were useful to localize places with more or less abundance of extractives (e.g., fats) in impregnated and unimpregnated wood, which varied considerably. Histochemical observations revealed information pertaining to the kiln dry specific distribution and redistribution of extractives between the areas. Moreover, resin reallocation and modification in ray parenchyma and resin canals induced by kiln drying would be another reason for the impregnation anomalies.
|
|
| 7. |
- Ahrenstedt, Lage, et al.
(författare)
-
Paper dry strength improvement by xyloglucan addition: Wet-end application, spray coating and synergism with borate
- 2008
-
Ingår i: Holzforschung. - 0018-3830 .- 1437-434X. ; 62:1, s. 8-14
-
Tidskriftsartikel (refereegranskat)abstract
- The polysaccharide xyloglucan as a wet-end additive improves paper properties. In the present study, paper strength improvement was analysed for dry handsheets made from chemical, mechanical and recycled pulps coated with xyloglucan in a spray application. Results are compared with sheets made from the same pulps treated with xyloglucan in the wet-end. Kraft pulp handsheets of bleached hardwood and softwood showed significant improvements of tensile, tear and Z-strength by xyloglucan spray treatment versus wet-end application, whereas handsheets of de-inked and thermomechanical pulp were improved only slightly. In both wet-end and spray applications, the effect of xyloglucan addition was intimately related to the presence of non-cellulosic components on the fibre surface. Further strength improvements were obtained for chemical pulps by addition of borax to the spray solution, which were likely to be due to the formation of borate-mediated xyloglucan cross-links. Spray coating of xyloglucan, with or without borax, thus represents a potential new application of this polysaccharide to increase paper dry strength.
|
|
| 8. |
- Al-Rudainy, Basel, et al.
(författare)
-
Antisolvent precipitation of hemicelluloses, lignosulfonates and their complexes from ultrafiltrated spent sulfite liquor (SSL)
- 2018
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 1437-434X .- 0018-3830. ; 72:10, s. 839-850
-
Tidskriftsartikel (refereegranskat)abstract
- The possibility of precipitating high molecular weight (MW) softwood hemicelluloses has been investigated. Solids were precipitated from a sodium-based spent sulfite liquor with the anti-solvents acetone, ethanol and methanol and the effects of solute concentration, pH and temperature on the precipitation were studied. The product yield, degree of separation, MW and structure of the different fractions were determined using gravimetric analysis, high performance liquid chromatography (HPLC), ultraviolet–visible (UV-Vis) spectroscopy, size exclusion chromatography (SEC), and two-dimensional nuclear magnetic resonance (2D NMR). A direct correlation was found between the dielectric constant (also called relative permittivity) of the bulk solution and the yield of precipitants, based on which the separation of the solutes was predictable. The highest yield and degree of separation observed was an intercept around 76% with 47.5% acetone, which was the most efficient anti-solvent.
|
|
| 9. |
|
|
| 10. |
- Alfredsen, Gry, et al.
(författare)
-
Characterisation of Postia placenta colonisation during 36 weeks in acetylated southern yellow pine sapwood at three acetylation levels including genomic DNA and gene expression quantification of the fungus
- 2016
-
Ingår i: Holzforschung. - : Walter de Gruyter GmbH. - 0018-3830 .- 1437-434X. ; 70:11, s. 1055-1065
-
Tidskriftsartikel (refereegranskat)abstract
- One way to protect timber in service against basidiomycete deterioration is by means of acetylation via reaction with acetic anhydride. The reason why acetylated wood (WAc) is resistant against decay fungi is still not exactly understood. The aim of this study was to contribute to this field of science, and Postia placenta colonisation after 4, 12, 20, 28 and 36 weeks was observed at three acetylation levels of Pinus spp. sapwood. Mass loss (ML) and wood moisture content (MC) data reflected the acetylation levels. The initial equilibrium MC (EMC) proved to be a good indicator of subsequent ML. Genomic DNA quantification showed P. placenta colonisation in all samples, also in samples where no ML were detectable. The number of expressed gene transcripts was limited, but the findings supported the results of previous studies: WAc seems to have some resistance against oxidative mechanisms, which are part of the metabolism of P. placenta. This leads to a delay in decay initiation, a delay in expression of genes involved in enzymatic depolymerisation, and a slower decay rate. The magnitudes of these effects are presented for each acetylation level. The data also imply that there is no absolute decay threshold at high acetylation levels, but instead a significant delay of decay initiation and a slower decay rate.
|
|
