| 1. |
- Adolfsson, Daniel, et al.
(author)
-
Cementitious phases in ladle slag
- 2011
-
In: Steel Research International. - : Wiley. - 1611-3683 .- 1869-344X. ; 82:4, s. 398-403
-
Journal article (peer-reviewed)abstract
- Ladle slag is an internal by-product generated within the steelmaking industry during the refining of steel. The realisation of beneficial inherent properties of ladle slag as a binder supplement or substitute material is believed to be advantageous with respect to both economy and environment for steelmakers. For this reason, the current study has focused on highlighting the properties of ladle slag that are pertinent to the formation of calcium aluminate hydrates. Three fractions of ladle slag, two of which were based on different slag formers, have been characterised using XRF, XRD and calorimetric analysis. Commonly known hydraulic minerals such as mayenite, tricalcium aluminate and dicalcium silicate were detected during analysis. An important aspect in the utilisation of ladle slag is the slag handling methodology. Therefore, this study also highlights and discusses the need to reconsider slag handling procedures concerning unnecessary exposure to weathering and the possible need for further processing of the slag in order to better employ the inherent hydraulic properties of this material.
|
|
| 2. |
- Ahmed, Hesham, et al.
(author)
-
Composite Pellets – A Potential Raw Material for Iron-Making
- 2014
-
In: Steel Research International. - : Wiley. - 1611-3683 .- 1869-344X. ; 85:3, s. 293-306
-
Research review (peer-reviewed)abstract
- Coke constitutes the major portion of iron-making cost and its production causes severe environmental concerns. In addition, lower energy consumption, lower CO2 emission and waste recycling are driving the Iron and steel making industry to develop “coke free, zero waste or green processes”. In the present article, an overview of possible ways to recognize a reasonable improvement in iron and steel making industry is summarized. The present discussion is focusing on the following approaches: 1. Replacing expensive coke with relatively less expensive alternate fuels having carbon as well as significant amount of hydrogen such as coal, waste plastic and biomass materials.2. Producing agglomerates from cheaper raw materials (secondary resources) as well as improving their performance in BF.3.Making the process towards higher carbon utilization by shifting the wustite equilibrium towards lower CO/CO2 ratio by using high reactive coke or catalytic activated one.4.Recycling the unused CO in the top gas by removing CO2 from the gas stream.Much attention has been paid to carbon composite agglomerates (CCA) as a promising raw material for future iron making. Production, mechanical and chemical suitability, reduction behavior, etc. are being elaborated. In addition, other possible ways to utilize CCA in alternate iron-making process has been explored.
|
|
| 3. |
- Ahmed, Hesham, et al.
(author)
-
Effect of the Ash from H2‐Rich Carbonaceous Materials on the Physicochemical Properties of Raceway Slag and Coke Reactivity
- 2020
-
In: Steel Research International. - : John Wiley & Sons. - 1611-3683 .- 1869-344X. ; 91:11
-
Journal article (peer-reviewed)abstract
- The iron and steel industry is one of the most important sectors worldwide, and it has a great impact on the global economy; however, this sector is still highly dependent on fossil carbon. To decrease this dependency, approaches to partially replace the injected pulverized coal with secondary, highly reactive, renewable (biomass) and H2‐rich materials have been studied. The injection of such materials is expected to significantly decrease the emitted CO2 from blast furnaces. However, due to the different ash composition of these alternative materials (especially alkali and alkaline earth metals) compared to that of ordinary injected coal, these materials are expected to alter the raceway slag properties and affect the coke reactivity. In the present article, the effect of the ash from different hydrogen‐rich carbonaceous materials on the raceway slag physicochemical properties as well as coke reactivity is reported. The melting characteristics of the ash briquettes in contact with the coke and wettability of the melted ash on the coke surface are determined visually using an optical heating microscope. The effect of the ash on the coke reactivity is studied by means of thermogravimetry under a continuous flow of CO2.
|
|
| 4. |
- Ai, S., et al.
(author)
-
Ab Initio Study on Continuous Evolution of Mechanical Properties in Phase-Transition Region of Low-Carbon Steel
- 2020
-
In: Steel Research International. - : Wiley-VCH Verlag. - 1611-3683 .- 1869-344X.
-
Journal article (peer-reviewed)abstract
- To control steel quality during continuous casting and subsequent heat treatment, an understanding of the evolution laws of mechanical properties during the austenite transition and the underlying mechanisms is of importance. Herein, the peak separation method is used to investigate the expansion behaviors in low-carbon steel. And the elastic properties of the matrix phase are calculated using the exact muffin-tin orbitals (EMTO) method. A continuous evolution model of high-temperature properties in the phase-transition region is established for ab initio data and experimental results. The evolution laws of the tetragonal shear elastic constant C′ and Young's modulus E agree well with that of the high-temperature strength. The critical temperature for ductility to brittleness is 850 °C. The matrix phase exhibits significantly brittleness character and increases slightly with decreasing temperature in single-phase paramagnetic (PM) γ-Fe region. The straightening zone temperature should be controlled above 950 °C to avoid cracks. In the austenite transition region, the drop rate of the magnetic moment reaches 18.90%. The findings suggest that the evolution law of mechanical properties of steels can be predicted from the elastic properties, especially during the austenite transition process, providing a basis for the prediction of material properties using ab initio methods.
|
|
| 5. |
- Albertsson, Galina, et al.
(author)
-
Effect of Low Oxygen Partial Pressure on the Chromium Partition in CaO-MgO-SiO2-Cr2O3-Al2O3 Synthetic Slag at Elevated Temperatures
- 2013
-
In: Steel Research International. - : Wiley. - 1611-3683 .- 1869-344X. ; 84:7, s. 670-679
-
Journal article (peer-reviewed)abstract
- The objective of the present work is to get an understanding of the impact of Al2O3 addition on the phase relationships in the CaO-MgO-Al2O3-SiO2-Cr2O3 slags at low oxygen partial pressures (P-O2 = 10(-4) Pa), with a view to control the precipitation of Cr-spinel in the slag. The equilibrium phases in CaO-MgO-Al2O3-SiO2-Cr2O3 slag system in the range on 1673-1873 K have been investigated. The compositions close to the industrial slag systems were chosen. The Cr2O3 content was fixed at 6 wt% and MgO at 8 wt%. Al2O3 contents in the slag were varied in the range of 3-12 wt%. The basicity (CaO/SiO2) of slag was set to 1.6. Gas/slag equilibrium technique was adopted. The samples were heated to 1873 K and soaked at this temperature for 24 h. The samples were then slow cooled to 1673 K and equilibrated for an additional 24 h. The oxygen partial pressure was kept at 10(-4) Pa. A gas mixture of CO/CO2 was used to control the oxygen partial pressure. After the equilibration, the samples were quenched in water. The chromium distribution and phase compositions in the quenched slags were studied using SEM-WDS and XRD techniques. The results were compared with the phase equilibrium calculations obtained from FACTSAGE software and the samples equilibrated in air. The size of spinel crystals increased drastically after slow cooling followed by annealing compared to samples being quenched after soaking at 1873 K. It was also found that low oxygen partial pressure had a strong impact on chromium partition. The amount of spinel phase increases with increased Al2O3 content.
|
|
| 6. |
- Allertz, Carl, et al.
(author)
-
A Study of Nitrogen Pickup from the Slag during Waiting Time of Ladle Treatment
- 2014
-
In: Steel Research International. - : Wiley. - 1611-3683 .- 1869-344X. ; 85:4, s. 689-696
-
Journal article (peer-reviewed)abstract
- An investigation of the nitrogen pickup of liquid steel from ladle slag after vacuum degassing was made. Nitride capacities, C-N, of a number of ladle slags were determined at controlled nitrogen and oxygen potentials at 1873K. The nitride capacities in the composition range studied were found to be very low. In accordance with the literature, the nitride capacity was found to increase with increasing SiO2 content. Industrial trials were performed. The nitrogen content of the steel was determined before and after vacuum degassing as well as after the waiting period. Three different trends of the variation of nitrogen content in the steel were observed. Both the laboratory study and the industrial trials revealed that the transfer of nitrogen from slag to steel was not the reason for nitrogen pickup in the steel subsequent to vacuum degassing.
|
|
| 7. |
- Almcrantz, M., et al.
(author)
-
Determination of inclusion characteristics in the Asea-SKF process using the modified spark-induced OES technique as a complement in studying the influence of top slag composition
- 2005
-
In: Steel Research International. - : Wiley. - 1611-3683 .- 1869-344X. ; 76:9, s. 624-634
-
Journal article (peer-reviewed)abstract
- The spark-induced modified optical emission spectroscopy (OES) technique developed by Ovako Steel makes it possible to rapidly determine inclusion characteristics in steel samples. In earlier investigations using the modified spark-induced OES technique for steel samples taken from billets, predicted oxygen contents agreed well with results from conventional melt extraction analyses. In this investigation, samples taken during ladle treatment in an ASEA-SKF ladle furnace were analysed using the modified OES technique. When comparing the results with inclusion characteristics determined by conventional analysis, similar trends were found. Plant trials were also carried out where three different top slag compositions were used. The purpose was to evaluate if the modified OES technique can be used to study the effect of changes in the refining operation on inclusion characteristics. Results indicated that the modified OES technique could be used to determine the effect of a changed slag composition on the inclusion characteristics in the steel. Since the modified OES method provides rapid feedback of inclusion characteristics, it has the potential of being used for faster optimisation of ladle refining operations.
|
|
| 8. |
- Andersson, Emma, et al.
(author)
-
The Effect of CaF2 in the Slag in Ladle Refining
- 2009
-
In: Steel Research International. - 1611-3683 .- 1869-344X. ; 80:8, s. 544-551
-
Journal article (peer-reviewed)abstract
- Industrial experiments were conducted in ladle treatment at SSAB Oxelosund aiming at a reduction and even elimination of CaF2 as a component in synthetic slag formers. The effects of the presence of CaF2 on sulphur refining, lining wear as well as types and amount of inclusions were examined. The results of the plant trials indicated that the new slag without CaF2 had enough capacity for sulphur removal. On the other hand, the presence of CaF2 as a flux in the slag resulted in profound lining wear. It was also found that both the number and the types of non-metallic inclusions were not affected by the elimination of CaF2 from synthetic slag. The origins of different types of inclusions were also analysed on the basis of the experimental results. The analysis supported the finding that the presence of CaF2 had little effect on inclusions.
|
|
| 9. |
- Andersson, Nils, et al.
(author)
-
Investigating the effectof slag on decarburization in an AOD converter using a fundamental model
- 2013
-
In: Steel Research International. - : Wiley. - 1611-3683 .- 1869-344X. ; 84:2, s. 169-177
-
Journal article (peer-reviewed)abstract
- A high-temperature thermodynamics model has been coupled with a fundamental mathematical model describing the fluid flow, where boundary conditions were chosen based on data for an industrial AOD converter. Using this model, the effect of both slag phases (a liquid part and a solid part) on the decarburization was studied. More specifically, the separation of chromium oxide to liquid slag as well as the effect of the amount of rigid top slag (solid)on the decarburization was investigated. The liquid slag was considered with respect to the uptake of chromium oxide, while the rigid top slag was only considered with respect to the increase of the metallostatic pressure in the steel melt. The results suggest that separation of chromium oxide to liquid slag results in a decreased decarburization rate. The same conclusion can be drawn with respect to the amount of solid top slag.
|
|
| 10. |
- Andersson, Nils Å. I., et al.
(author)
-
An in-Depth Model-Based Analysis of Decarburization in the AOD Process
- 2012
-
In: Steel Research International. - : Wiley. - 1611-3683 .- 1869-344X. ; 83:11, s. 1039-1052
-
Journal article (peer-reviewed)abstract
- A previously reported flow and reaction model for an argon-oxygen decarburization converter was extended to also include a thermodynamic description. An in-depth study of the model results has been conducted to answer how concentrations of elements and species in the converter at different locations change with time. This may contribute to the understanding of the mechanisms of the refining procedure in the argon-oxygen decarburization process. The refining procedure includes several step-wise changes of an injected gas composition to higher and higher inert gas ratio, called step changes. A step change leads to a decreased partial pressure of carbon monoxide and maintains the decarburization at a higher efficiency. The results shows early and late concentration profiles for the first injection step and suggests a way to determine when a step change should be made. Moreover, the step change could be determined by calculating the carbon concentration profiles and deciding when the carbon concentration gradients start to diminish.
|
|
