| 1. |
- Abadeer, N. S., et al.
(författare)
-
Interactions of Bacterial Lipopolysaccharides with Gold Nanorod Surfaces Investigated by Refractometric Sensing
- 2015
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 7:44, s. 24915-24925
-
Tidskriftsartikel (refereegranskat)abstract
- The interface between nanoparticles and bacterial surfaces is of great interest for applications in nanomedicine and food safety. Here, we demonstrate that interactions between gold nanorods and bacterial surface molecules are governed by the nanoparticle surface coating. Polymer-coated gold nanorod substrates are exposed to lipopolysaccharides extracted from Pseudomonas aeruginosa, Salmonella enterica and Escherichia coli, and attachment is monitored using localized surface plasmon resonance refractometric sensing. The number of lipopolysaccharide molecules attached per nanorod is calculated from the shift in the plasmon maximum, which results from the change in refractive index after analyte binding. Colloidal gold nanorods in water are also incubated with lip opolysaccharides to demonstrate the effect of lipopolysaccharide concentration on plasmon shift, zeta-potential, and association constant. Both gold nanorod surface charge and surface chemistry affect gold nanorod lipopolysaccharide interactions. In general, anionic lipopolysaccharides was found to attach more effectively to cationic gold nanorods than to neutral or anionic gold nanorods. Some variation in lipopolysaccharide attachment is also observed between the three strains studied, demonstrating the potential complexity of bacteria nanoparticle interactions.
|
|
| 2. |
- Abdelhamid, Hani Nasser, 1986-, et al.
(författare)
-
Three-Dimensional Printing of Cellulose/Covalent Organic Frameworks (CelloCOFs) for CO2 Adsorption and Water Treatment
- 2023
-
Ingår i: ACS Applied Materials and Interfaces. - 1944-8244 .- 1944-8252. ; 15:51, s. 59795-59805
-
Tidskriftsartikel (refereegranskat)abstract
- The development of porous organic polymers, specifically covalent organic frameworks (COFs), has facilitated the advancement of numerous applications. Nevertheless, the limited availability of COFs solely in powder form imposes constraints on their potential applications. Furthermore, it is worth noting that COFs tend to undergo aggregation, leading to a decrease in the number of active sites available within the material. This work presents a comprehensive methodology for the transformation of a COF into three-dimensional (3D) scaffolds using the technique of 3D printing. As part of the 3D printing process, a composite material called CelloCOF was created by combining cellulose nanofibrils (CNF), sodium alginate, and COF materials (i.e., COF-1 and COF-2). The intervention successfully mitigated the agglomeration of the COF nanoparticles, resulting in the creation of abundant active sites that can be effectively utilized for adsorption purposes. The method of 3D printing can be described as a simple and basic procedure that can be adapted to accommodate hierarchical porous materials with distinct micro- and macropore regimes. This technology demonstrates versatility in its use across a range of COF materials. The adsorption capacities of 3D CelloCOF materials were evaluated for three different adsorbates: carbon dioxide (CO2), heavy metal ions, and perfluorooctanesulfonic acid (PFOS). The results showed that the materials exhibited adsorption capabilities of 19.9, 7.4–34, and 118.5–410.8 mg/g for CO2, PFOS, and heavy metals, respectively. The adsorption properties of the material were found to be outstanding, exhibiting a high degree of recyclability and exceptional selectivity. Based on our research findings, it is conceivable that the utilization of custom-designed composites based on COFs could present new opportunities in the realm of water and air purification.
|
|
| 3. |
- Aboulfadl, Hisham, 1986, et al.
(författare)
-
Alkali Dispersion in (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells - Insight from Theory and Experiment
- 2021
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 13:6, s. 7188-7199
-
Tidskriftsartikel (refereegranskat)abstract
- Silver alloying of Cu(In,Ga)Se2 absorbers for thin film photovoltaics offers improvements in open-circuit voltage, especially when combined with optimal alkali-treatments and certain Ga concentrations. The relationship between alkali distribution in the absorber and Ag alloying is investigated here, combining experimental and theoretical studies. Atom probe tomography analysis is implemented to quantify the local composition in grain interiors and at grain boundaries. The Na concentration in the bulk increases up to ∼60 ppm for [Ag]/([Ag] + [Cu]) = 0.2 compared to ∼20 ppm for films without Ag and up to ∼200 ppm for [Ag]/([Ag] + [Cu]) = 1.0. First-principles calculations were employed to evaluate the formation energies of alkali-on-group-I defects (where group-I refers to Ag and Cu) in (Ag,Cu)(In,Ga)Se2 as a function of the Ag and Ga contents. The computational results demonstrate strong agreement with the nanoscale analysis results, revealing a clear trend of increased alkali bulk solubility with the Ag concentration. The present study, therefore, provides a more nuanced understanding of the role of Ag in the enhanced performance of the respective photovoltaic devices.
|
|
| 4. |
- Agostini, Marco, 1987, et al.
(författare)
-
Free-Standing 3D-Sponged Nanofiber Electrodes for Ultrahigh-Rate Energy-Storage Devices
- 2018
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8252 .- 1944-8244. ; 10:40, s. 34140-34146
-
Tidskriftsartikel (refereegranskat)abstract
- We have designed a self-standing anode built-up from highly conductive 3D-sponged nanofibers, that is, with no current collectors, binders, or additional conductive agents. The small diameter of the fibers combined with an internal spongelike porosity results in short distances for lithium-ion diffusion and 3D pathways that facilitate the electronic conduction. Moreover, functional groups at the fiber surfaces lead to the formation of a stable solid-electrolyte interphase. We demonstrate that this anode enables the operation of Li-cells at specific currents as high as 20 A g-1 (approx. 50C) with excellent cycling stability and an energy density which is >50% higher than what is obtained with a commercial graphite anode.
|
|
| 5. |
- Ahmad, Mariam, et al.
(författare)
-
Uncovering the Electronic State Interplay at Metal Oxide Electron Transport Layer/Nonfullerene Acceptor Interfaces in Stable Organic Photovoltaic Devices
- 2023
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 15:47, s. 55065-55072
-
Tidskriftsartikel (refereegranskat)abstract
- The implementation of sputter-deposited TiOx as an electron transport layer in nonfullerene acceptor-based organic photovoltaics has been shown to significantly increase the long-term stability of devices compared to conventional solution-processed ZnO due to a decreased photocatalytic activity of the sputtered TiOx. In this work, we utilize synchrotron-based photoemission and absorption spectroscopies to investigate the interface between the electron transport layer, TiOx prepared by magnetron sputtering, and the nonfullerene acceptor, ITIC, prepared in situ by spray deposition to study the electronic state interplay and defect states at this interface. This is used to unveil the mechanisms behind the decreased photocatalytic activity of the sputter-deposited TiOx and thus also the increased stability of the organic solar cell devices. The results have been compared to similar measurements on anatase TiOx since anatase TiOx is known to have a strong photocatalytic activity. We show that the deposition of ITIC on top of the sputter-deposited TiOx results in an oxidation of Ti3+ species in the TiOx and leads to the emergence of a new O 1s peak that can be attributed to the oxygen in ITIC. In addition, increasing the thickness of ITIC on TiOx leads to a shift in the O 1s and C 1s core levels toward higher binding energies, which is consistent with electron transfer at the interface. Resonant photoemission at the Ti L-edge shows that oxygen vacancies in sputtered TiOx lie mostly in the surface region, which contrasts the anatase TiOx where an equal distribution between surface and subsurface oxygen vacancies is observed. Furthermore, it is shown that the subsurface oxygen vacancies in sputtered TiOx are strongly reduced after ITIC deposition, which can reduce the photocatalytic activity of the oxide, while the oxygen vacancies in model anatase TiOx are not affected upon ITIC deposition. This difference can explain the inferior photocatalytic activity of the sputter-deposited TiOx and thus also the increased stability of devices with sputter-deposited TiOx used as an electron transport layer.
|
|
| 6. |
- Al-Shammari, Rusul M., et al.
(författare)
-
Photoinduced Enhanced Raman from Lithium Niobate on Insulator Template
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 10:36, s. 30871-30878
-
Tidskriftsartikel (refereegranskat)abstract
- Photoinduced enhanced Raman spectroscopy from a lithium niobate on insulator (LNOI)−silver nanoparticle template is demonstrated both by irradiating the template with 254 nm ultraviolet (UV) light before adding an analyte and before placing the substrate in the Raman system (substrate irradiation) and by irradiating the sample in the Raman system after adding the molecule (sample irradiation). The photoinduced enhancement enables up to an ∼sevenfold increase of the surface-enhanced Raman scattering signal strength of an analyte following substrate irradiation, whereas an ∼threefold enhancement above the surface-enhanced signal is obtained for sample irradiation. The photoinduced enhancement relaxes over the course of ∼10 h for a substrate irradiation duration of 150 min before returning to initial signal levels. The increase in Raman scattering intensity following UV irradiation is attributed to photoinduced charge transfer from the LNOI template to the analyte. New Raman bands are observed following UV irradiation, the appearance of which is suggestive of a photocatalytic reaction and highlight the potential of LNOI as a photoactive surface-enhanced Raman spectroscopy substrate.
|
|
| 7. |
- Aldred, Nick, et al.
(författare)
-
Real-Time Quantification of Microscale Bioadhesion Events In situ Using Imaging Surface Plasmon Resonance (iSPR)
- 2011
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 3:6, s. 2085-2091
-
Tidskriftsartikel (refereegranskat)abstract
- From macro- to nanoscales, adhesion phenomena are all-pervasive in nature yet remain poorly understood. In recent years, studies of biological adhesion mechanisms, terrestrial and marine, have provided inspiration for "biomimetic" adhesion strategies and important insights for the development of fouling-resistant materials. Although the focus of most contemporary bioadhesion research is on large organisms such as marine mussels, insects and geckos, adhesion events on the micro/nanoscale are critical to our understanding of important underlying mechanisms. Observing and quantifying adhesion at this scale is particularly relevant for the development of biomedical implants and in the prevention of marine biofouling. However, such characterization has so far been restricted by insufficient quantities of material for biochemical analysis and the limitations of contemporary imaging techniques. Here, we introduce a recently developed optical method that allows precise determination of adhesive deposition by microscale organisms in situ and in real time; a capability not before demonstrated. In this extended study we used the cypris larvae of barnacles and a combination of conventional and imaging surface plasmon resonance techniques to observe and quantify adhesive deposition onto a range of model surfaces (CH(3)-, COOH-, NH(3)-, and mPEG-terminated SAMs and a PEGMA/HEMA hydrogel). We then correlated this deposition to passive adsorption of a putatively adhesive protein from barnacles. In this way, we were able to rank surfaces in order of effectiveness for preventing barnacle cyprid exploration and demonstrate the importance of observing the natural process of adhesion, rather than predicting surface effects from a model system. As well as contributing fundamentally to the knowledge on the adhesion and adhesives of barnacle larvae, a potential target for future biomimetic glues, this method also provides a versatile technique for laboratory testing of fouling-resistant chemistries.
|
|
| 8. |
- Ali, A., et al.
(författare)
-
Effect of Alkali Carbonates (Single, Binary, and Ternary) on Doped Ceria : A Composite Electrolyte for Low-Temperature Solid Oxide Fuel Cells
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 10:1, s. 806-818
-
Tidskriftsartikel (refereegranskat)abstract
- Samarium-doped ceria (SDC) carbonate has become an attractive electrolyte for fuel cells because of its remarkable ion conductivity and high performance. Different doped ceria-carbonate (single-carbonate SDC, binary-carbonate SDC, and ternary-carbonate SDC) electrolytes were synthesized by the coprecipitation/oxalate method, to optimize the electrochemical performance. The structure; morphology; and thermal, optical, and surface properties have been studied using a variety of techniques. The X-ray diffraction results confirmed the successful incorporation of samarium into ceria as a crystalline structure and inclusion of carbonate, which is amorphous in nature. To analyze the conduction mechanism, direct current conductivity was measured in a H2/O2 atmosphere. Doped ceria-binary carbonate ((Li/Na)CO3-SDC) showed the best conductivity of 0.31 S cm-1 and power density of 617 mW cm-2, at 600 °C. The enhancement in the ionic conductivity and performance of the composites is due to the contribution of hybrid ions (O2-, H+). The crystallite size of the composites was in the range 21-41 nm. For the calculation of band gaps, optical absorption spectra of the synthesized powders were analyzed, and they showed a red shift with the band gap energy in the range 2.6-3.01 eV, when compared to that of pure ceria (3.20 eV).
|
|
| 9. |
- Alipoormazandarani, Niloofar, et al.
(författare)
-
Functional Lignin Nanoparticles with Tunable Size and Surface Properties : Fabrication, Characterization, and Use in Layer-by-Layer Assembly
- 2021
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 13:22, s. 26308-26317
-
Tidskriftsartikel (refereegranskat)abstract
- Lignin is the richest source of renewable aromatics and has immense potential for replacing synthetic chemicals. The limited functionality of lignin is, however, challenging for its potential use, which motivates research for creating advanced functional lignin-derived materials. Here, we present an aqueous-based acid precipitation method for preparing functional lignin nanoparticles (LNPs) from carboxy-methylated or carboxy-pentylated lignin. We observe that the longer grafted side chains of carboxy-pentylated lignin allow for the formation of larger LNPs. The functional nanoparticles have high tolerance against salt and aging time and well-controlled size distribution with R-h <= 60 nm over a pH range of 5-11. We further investigate the layer-by-layer (LbL) assembly of the LNPs and poly(allylamine hydrochloride) (PAH) using a stagnation point adsorption reflectometry (SPAR) and quartz crystal microbalance with dissipation (QCM-D). Results demonstrate that LNPs made of carboxypentylated lignin (i.e., PLNPs with the adsorbed mass of 3.02 mg/m(2)) form a more packed and thicker adlayer onto the PAH surface compared to those made of carboxymethylated lignin (i.e., CLNPs with the adsorbed mass of 2.51 mg/m(2)). The theoretical flux, J, and initial rate of adsorption, (d Gamma/dt)(0), analyses confirm that 22% of PLNPs and 20% of CLNPs arriving at the PAH surface are adsorbed. The present study provides a feasible platform for engineering LNPs with a tunable size and adsorption behavior, which can be adapted in hionanomaterial production.
|
|
| 10. |
- Alipour, Nazanin, et al.
(författare)
-
VOC-Induced Flexing of Single and Multilayer Polyethylene Films As Gas Sensors
- 2016
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 8:15, s. 9946-9953
-
Tidskriftsartikel (refereegranskat)abstract
- The differential swelling and bending of multilayer polymeric films due to the dissimilar uptake of volatile organic compounds (VOCs; n-hexane, limonene) in the different layers was studied. Motions of thin polyethylene films triggered by the penetrant were investigated to learn more about how their deformation is related to VOC absorption. Single layers of metallocene or low-density polyethylene, and multilayers (2-288-layers) of these in alternating positions were considered. Single-, 24-, and 288 layer films displayed no motion when uniformly subjected to VOCs, but they could display simple curving modes when only one side of the film was wetted with a liquid VOC. Two-layer films displayed simple bending when uniformly subjected to VOCs due to the different swelling in the two layers, but when the VOC was applied to only one side of the film, more complex modes of motion as well as dynamic oscillations were observed (e.g., constant amplitude wagging at 2 Hz for ca. 50 s until all the VOC had evaporated). Diffusion modeling was used to study the transport behavior of VOCs inside the films and the different bending modes. Finally a prototype VOC sensor was developed, where the reproducible curving of the two-layer film was calibrated with n-hexane. The sensor is simple, cost-efficient, and nondestructive and requires no electricity.
|
|
