| 1. |
- Brinkfeldt, Klas, et al.
(författare)
-
Thermo-Mechanical Simulations of SiC Power Modules with Single and Double Sided Cooling
- 2015
-
Ingår i: 16th International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems (EuroSimE), 2015. - : Institute of Electrical and Electronics Engineers Inc.. - 9781479999491 - 9781479999507 ; , s. 1 - 7
-
Konferensbidrag (refereegranskat)abstract
- Effectively removing dissipated heat from the switching devices enables a higher current carrying capability per chip area ratio, thus leading to smaller or fewer devices for a given power requirement specification. Further, the use of SiC based devices has proven to increase the efficiency of the system thereby reducing the dissipated heat. Thermal models have been used to compare SiC power modules. Single and double sided cooling have been simulated. The simulated maximum temperatures were 141 °C for the single sided version and 119.7 °C for the double sided version. In addition, the reliability of a single sided module and thermally induced plastic strains of a double sided module have been investigated. A local model of the wire bond interface to the transistor metallization shows a 30/00 maximum increase in plastic strain during the power cycle. Simulations of the creep strain rates in the die attach solder layer for a power cycling loads also shows a 30/00 increase in creep strain per cycle.
|
|
| 2. |
- Belov, Ilja, et al.
(författare)
-
The effect of variations in temperature cycling profile and mechanical properties of solder on thermo-mechanical reliability of a lead-free BGA package
- 2015
-
Ingår i: Proceedings of the 16th International Conference IEEE EuroSimE 2015. - Piscataway : IEEE Press. - 9781479999514 ; , s. 165-169, s. 165-169
-
Konferensbidrag (refereegranskat)abstract
- The paper investigates the effect of variations both in temperature cycling profile and in SAC305 solder Young's modulus in the PBGA256 package on the thermo-mechanical reliability. FE simulations quantify the effect of cycle reduction and counting techniques by introducing different temperature profiles having identical dwell- and period time characteristics. A difference of 30% in predicted accumulated creep strain energy density per cycle has been determined for the studied profiles. Under the provided modelling assumptions and simplifications, the maximum variation of the thermal fatigue life of SAC305 solder joints is within 30% as the result of experimentally determined Young's modulus variation in as-delivered packages.
|
|
| 3. |
- Brinkfeldt, Klas, et al.
(författare)
-
Model verification of heat exchangers in a flow test rig
- 2015
-
Ingår i: 2015 16th International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems, EuroSimE 2015. - : Institute of Electrical and Electronics Engineers Inc.. - 9781479999507 ; , s. 7103135-
-
Konferensbidrag (refereegranskat)abstract
- In power electronics, more efficient removal of heat from the junction of power devices leads to a higher power rating per die, which in turn leads to fewer die and reduced system volume. Since temperature is a main driver in expected failure modes an increase in cooling capability can also enhance margins of the device reliability. Previously, CFD simulations of two novel heat exchanger designs that will be used in a power module with double sided cooling have been reported on. The heat exchangers are fabricated by direct 3D manufacturing of copper structures, which allows almost complete freedom in geometric design. Two novel geometries of heat exchanger cooling structures have previously been modeled in terms of thermal performance and expected pressure drop. A flow rig has been designed and calibrated to measure thermal performance and pressure drops of these heat sinks. For calibration purposes, measurements of the thermal response of wave structured and unstructured heat sinks are reported here. The results show that, as expected, the heat sink temperatures are lower for all flow rates in the wavestructured geometry. A thermal CFO model accurately predicts the behavior of the temperature difference between inlet and outlet versus flow rate, but predicts higher absolute temperature values. It was also found that the model underestimates the pressure drop over the tested heat sillies. The pressure drop across a novel pine cone geometry heat sink fabricated by additive manufacturing methods was also measured. Comparisons to a reduced model, which neglects everything before the inlet and after the outlet of the tested device, showed that the behavior of this pine structured heat sink was not predicted correctly. The pressure drop increased more rapidly with flow rates in the model than in the measurements. The main source of error in the measurements and simulations comes from a lack of thermal loading. Future work to improve the flow rig includes possibilities to increase the temperature loading at the bottom of the heat sink under test.
|
|
