| 1. |
- Haris, Abdullah, et al.
(författare)
-
Prolonged Repellent Activity of Plant Essential Oils against Dengue Vector, Aedes aegypti
- 2023
-
Ingår i: Molecules. - : MDPI AG. - 1431-5157 .- 1420-3049. ; 28:3
-
Tidskriftsartikel (refereegranskat)abstract
- Repellents are effective personal protective means against outdoor biting mosquitoes. Repellent formulations composed of EOs are finding increased popularity among consumers. In this study, after an initial screening of 11 essential oils (EOs) at the concentration of 33 μg/cm2, five of the most repellent EOs, Perovskia atriplicifolia, Citrus reticulata (fruit peels), C. reticulata (leaves), Mentha longifolia, and Dysphania ambrosioides were further investigated for repellent activity against Aedes aegypti mosquitoes in time span bioassays. When tested at the concentrations of 33 μg/cm2, 165 μg/cm2 and 330 μg/cm2, the EO of P. atriplicifolia showed the longest repellent effect up to 75, 90 and 135 min, respectively, which was followed by C. reticulata (peels) for 60, 90 and 120 min, M. longifolia for 45, 60 and 90 min, and C. reticulata (leaves) for 30, 45 and 75 min. Notably, the EO of P. atriplicifolia tested at the dose of 330 μg/cm2 showed complete protection for 60 min which was similar to the commercial mosquito repellent DEET. Gas chromatographic-mass spectrometric analyses of the EOs revealed camphor (19.7%), limonene (92.7%), sabinene (24.9%), carvone (82.6%), and trans-ascaridole (38.8%) as the major constituents of P. atriplicifolia, C. reticulata (peels), C. reticulata (leaves), M. longifolia, and D. ambrosioides, respectively. The results of the present study could help develop plant-based commercial repellents to protect humans from dengue mosquitoes.
|
|
| 2. |
- Abbas, Muhammad Ghazanfar, et al.
(författare)
-
Chemical Composition, Larvicidal and Repellent Activities of Wild Plant Essential Oils against Aedes aegypti
- 2023
-
Ingår i: Biology. - : MDPI AG. - 2079-7737. ; 12:1
-
Tidskriftsartikel (refereegranskat)abstract
- Bio-degradable and eco-friendly essential oils (EOs) extracted from Mentha longifolia, Salsola imbricata, Erigeron bonariensis, E. canadensis, Ailanthus altissima, and Zanthoxylum armatum were investigated for their repellent and larvicidal potential against Aedes aegypti mosquitoes. The EOs of M. longifolia, S. imbricata, E. bonariensis, E. canadensis, A. altissima, and Z. armatum exhibited 99.0%, 96.8%, 40.2%, 41.7%, 29.1%, and 13.2% repellency against mosquitoes at a tested dose of 33.3 μg/cm2, respectively. In time span bioassays, the EOs of M. longifolia, S. imbricata, E. bonariensis, and E. canadensis showed more than 40% repellency for 60 min at a tested dose of 330 μg/cm2. Larvicidal bioassays revealed that larvae of Ae. aegypti were the most susceptible to M. longifolia (LC50, 39.3 mg/L), E. bonariensis (LC50, 26.0 mg/L), E. canadensis (LC50, 35.7 mg/L), and Z. armatum (LC50, 35.9 mg/L) EOs upon 48 h exposure. The most abundant constituents in the EOs of M. longifolia, S. imbricata, E. bonariensis, E. canadensis and A. altissima were piperitone oxide (45.5%), carvone (39.9%), matricaria ester (43.1%), (31.7%) and eugenol (24.4%), respectively. Our study demonstrates that EOs of M. longifolia, S. imbricata, E. bonariensis, and E. canadensis might be used to control Ae. aegypti mosquitoes without harming humans or the environment.
|
|
| 3. |
- Parveen, Amna, et al.
(författare)
-
Chemical composition of essential oils from natural populations of Artemisia scoparia collected at different altitudes : antibacterial, mosquito repellent, and larvicidal effects
- 2024
-
Ingår i: Molecules. - 1431-5157 .- 1420-3049. ; 29:6, s. 1359-
-
Tidskriftsartikel (refereegranskat)abstract
- The current study aimed to evaluate the presence of chemical variations in essential oils (EOs) extracted from Artemisia scoparia growing at different altitudes and to reveal their antibacterial, mosquito larvicidal, and repellent activity. The gas chromatographic–mass spectrometric analysis of A. scoparia EOs revealed that the major compounds were capillene (9.6–31.8%), methyleugenol (0.2–26.6%), β-myrcene (1.9–21.4%), γ-terpinene (1.5–19.4%), trans-β-caryophyllene (0.8–12.4%), and eugenol (0.1–9.1%). The EO of A. scoparia collected from the city of Attock at low elevation was the most active against Staphylococcus aureus, Bacillus subtilis, Escherichia coli, and Pseudomonas aeruginosa bacteria (minimum inhibitory concentration of 156–1250 µg/mL) and showed the best mosquito larvicidal activity (LC50, 55.3 mg/L). The EOs of A. scoparia collected from the high-altitude areas of Abbottabad and Swat were the most repellent for females of Ae. aegypti and exhibited repellency for 120 min and 165 min, respectively. The results of the study reveal that different climatic conditions and altitudes have significant effects on the chemical compositions and the biological activity of essential oils extracted from the same species.
|
|
| 4. |
- Ullah, Muhammad Kaleem, et al.
(författare)
-
Tri-doped ceria (M0.2Ce0.8O2-δ, M= Sm0.1 Ca0.05 Gd0.05) electrolyte for hydrogen and ethanol-based fuel cells
- 2019
-
Ingår i: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388. ; 773, s. 548-554
-
Tidskriftsartikel (refereegranskat)abstract
- In recent scientific research, an interest has been gained significantly by rare earth metals such as cerium (Ce), samarium (Sm) and gadolinium (Gd) due to their use in fuel cells as electrolyte and catalysts. When used in an electrolyte, these materials lower the fuel cell's operating temperature compared to a conventional electrolyte, for example, yittria-stabilized zirconia (YSZ) which operates at a high temperature (≥800 °C). In this paper, the tri-doped ceria, M0.2Ce0.8O2-δ(M = Sm0.1Ca0.05Gd0.05) electrolyte powders was synthesized using the co-precipitation method at 80 °C. These dopants were used for CeO2with a total molar ratio of 1 M. Dry-pressed powder technique was used to make fuel cell pellets from the powder and placed them in the furnace to sinter at 700 °C for 60 min. Electrical conductivity of such a pellet in air was 1.2 × 10−2S cm−1at 700 °C measured by the ProboStat-NorECs setup. The crystal structure was determined with the help of X-ray diffraction (XRD), which showed that all the dopants were successfully doped in CeO2. Raman spectroscopy and UV-VIS spectroscopy were also carried out to analyse the molecular vibrations and absorbance, respectively. The maximum open-circuit voltages (OCVs) for hydrogen and ethanol fuelled at 550 °C were observed to be 0.89 V and 0.71 V with power densities 314 mW cm−2and 52.8 mW cm−2, respectively.
|
|
| 5. |
- Afroz, Laila, et al.
(författare)
-
Nanocomposite Catalyst (1 – x)NiO-xCuO/yGDC for Biogas Fueled Solid Oxide Fuel Cells
- 2023
-
Ingår i: ACS Applied Energy Materials. - : American Chemical Society (ACS). - 2574-0962. ; 6:21, s. 10918-10928
-
Tidskriftsartikel (refereegranskat)abstract
- The composites of Ni–Cu oxides with gadolinium doped ceria (GDC) are emerging as highly proficient anode catalysts, owing to their remarkable performance for solid oxide fuel cells operated with biogas. In this context, the nanocomposite catalysts (1 – x)NiO-xCuO/yGDC (x = 0.2–0.8; y = 1,1.3) are synthesized using a solid-state reaction route. The cubic and monoclinic structures are observed for NiO and CuO phases, respectively, while CeO2 showed cubic fluorite structure. The scanning electron microscopic images revealed a rise in the particle size with an increase in the copper and GDC concentration. The optical band gap values are calculated in the range 2.82–2.33 eV from UV–visible analysis. The Raman spectra confirmed the presence of vibration modes of CeO2 and NiO. The electrical conductivity of the nanocomposite anodes is increased as the concentration of copper and GDC increased and reached at 9.48 S cm–1 for 0.2NiO-0.8CuO/1.3GDC composition at 650 °C. The electrochemical performance of (1 – x)NiO-xCuO/yGDC (x = 0.2–0.8; y = 1,1.3)-based fuel cells is investigated with biogas fuel at 650 °C. Among all of the as-synthesized anodes, the fuel cell with composition 0.2NiO-0.8CuO/1.3GDC showed the best performance, such as an open circuit voltage of 0.84 V and peak power density of 72 mW cm–2. However, from these findings, it can be inferred that among all other compositions, the 0.2NiO-0.8CuO/1.3GDC anode is a superior combination for the high electrochemical performance of solid oxide fuel cells fueled with biogas.
|
|
| 6. |
- Rafique, Asia, et al.
(författare)
-
Multioxide phase-based nanocomposite electrolyte (M@SDC where M = Zn2+ / Ba2+/ La2+/Zr-2/Al3+) materials
- 2020
-
Ingår i: Ceramics International. - : ELSEVIER SCI LTD. - 0272-8842 .- 1873-3956. ; 46:52, s. 6882-6888
-
Tidskriftsartikel (refereegranskat)abstract
- This paper deals with the development of a highly dense and stable electrolyte on the base of nanoionics oxide interface theory. This gives a comparative study of two-phase nanocomposite electrolytes that are developed for low temperature solid oxide fuel cells (LT-SOFCs). These nanocomposites are synthesised with different oxides, which are coated on the doped ceria that showed high oxide ion mobility for LT-SOFCs. These novel two-phase nanocomposite oxide ionic conductors (MCe0.8Sm0.2O2-MO2, where M = Zn2+/Ba2+/La3+/Zr2+/Al3+) were synthesised by a co-precipitation method. The interface study between these two phases was analysed by electrochemical impedance spectroscopy (EIS), while ionic conductivities were measured with DC conductivity (four probe method). The nanocomposite electrolytes exhibited higher conductivities with the increase of concentration of coated oxides but decreased at a certain level. The structural or morphological properties of the nanocomposite electrolytes were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The thermal stability was investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The maximum performance of 590 mW/cm(2) at 550 degrees C was obtained for the Zn@SDC based cell, and the rest of the coated samples Ba@SDC, La@SDC, Zr@SDC and Al@SDC based cells showed values of 550 mW/cm(2), 540 mW/cm(2), 450 mW/cm(2), 340 mW/cm(2), respectively, with hydrogen as a fuel. Therefore, the coated-SDC based nanocomposite materials are a good approach for lowering the operating temperature to achieve the challenges of the solid oxide fuel cells (SOFC). These two-phase nanocomposite electrolytes satisfy the all requirements which one electrolyte should have, like high ionic conduction, thermodynamic stability and negligible electronic conduction.
|
|
| 7. |
- Ajmal Khan, Muhammad, et al.
(författare)
-
Comparative study of the nano-composite electrolytes based on samaria-doped ceria for low temperature solid oxide fuel cells (LT-SOFCs)
- 2013
-
Ingår i: International journal of hydrogen energy. - : Elsevier BV. - 0360-3199 .- 1879-3487. ; 38:36, s. 16524-16531
-
Tidskriftsartikel (refereegranskat)abstract
- Ceria-based electrolyte materials have great potential in low and intermediate temperature solid oxide fuel cell applications. In the present study, three types of ceria-based nanocomposite electrolytes (LNK-SDC, LN-SDC and NK-SDC) were synthesized. One-step co-precipitation method was adopted and different techniques were applied to characterize the obtained ceria-based nano-composite electrolyte materials. TGA, XRD and SEM were used to analyze the thermal effect, crystal structure and morphology of the materials. Cubic fluorite structures have been observed in all composite electrolytes. Furthermore, the crystallite sizes of the LN-SDC, NK-SDC, LNK-SDC were calculated by Scherrer formula and found to be in the range 20 nm, 21 nm and 19 nm, respectively. These values emphasize a good agreement with the SEM results. The ionic conductivities were measured using EIS (Electrochemical Impedance Spectroscopy) with two-probe method and the activation energies were also calculated using Arrhenius plot. The maximum power density was achieved 484 mW/cm(2) of LNK-SDC electrolyte at 570 degrees C using the LiCuZnNi oxide electrodes.
|
|
| 8. |
- Khan, M. Ajmal, et al.
(författare)
-
Synthesize and characterization of ceria based nano-composite materials for low temperature solid oxide fuel cell
- 2018
-
Ingår i: International journal of hydrogen energy. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0360-3199 .- 1879-3487. ; 43:12, s. 6310-6317
-
Tidskriftsartikel (refereegranskat)abstract
- The present study is focused on ceria based mixed (ionic and electronic conductor) composite Al0.05Ni0.1Ti0.05Zn0.80-SDC (ATZN-SDC) oxide material was prepared by solid state reaction, which can be used as anode materials for solid oxide fuel cell. The effect of Ti and Al oxides were analyzed on the NiZn-SDC composite with respect to its conductivity and catalytic activity in hydrogen atmosphere. The average crystallite size of the composite was found to be 40-100 nm by XRD and SEM. The DC conductivity was determined by 4-probe technique. The electrochemical impedance spectrum (EIS) was also examined in hydrogen atmosphere within a temperature range of 350-550 degrees C. The maximum power density 370 mW/cm(2) was achieved at 650 degrees C.
|
|
