| 1. |
- Bhatti, Adeel Liaquat, et al.
(författare)
-
An Efficient and Functional Fe3O4/Co3O4 Composite for Oxygen Evolution Reaction
- 2021
-
Ingår i: Journal of Nanoscience and Nanotechnology. - : AMER SCIENTIFIC PUBLISHERS. - 1533-4880 .- 1533-4899. ; 21:4, s. 2675-2680
-
Tidskriftsartikel (refereegranskat)abstract
- The design of efficient, stable, durable and noble metal free electro catalysts for oxygen evolution reaction (OER) are of immediate need, but very challenging task. In this study, iron induction into cobalt oxide (Co3O4) has resulted composite structure by wet chemical method. The iron impurity has brought an electronic disorder into Fe3O4/cobalt oxide composite thereby efficient oxygen evolution reaction is demonstrated. An addition of iron content into composite resulted the alternation of morphology from Nano rods to clusters of nanoparticles. The successive addition of iron into composite system reduced the onset potential of OER as compared to the pristine cobalt oxide. A Tafel slope of 80 mVdec(-1) indicates the favorable oxygen evolution reaction kinetics on the sample 4. An over-potential of 370 mV is required to reach a 10 mAcm(-2) current density which is acceptable for a nonprecious catalyst. The catalyst is highly durable and stable for 30 hours. Electrochemical impedance spectroscopy further provided a deeper insight on charge transfer resistance and sample 4 has low charge transfer resistance that supported the OER polarization curves. The sample 4 has more electrochemical active surface area of 393.5 cm(2). These obtained results are exciting and highlighting the importance of composite structure and leave a huge space for the future investigations on composite materials for energy related applications.
|
|
| 2. |
- Bhatti, Adeel Liaquat, et al.
(författare)
-
Facile doping of nickel into Co3O4 nanostructures to make them efficient for catalyzing the oxygen evolution reaction
- 2020
-
Ingår i: RSC Advances. - : Royal Society of Chemistry. - 2046-2069. ; 10:22, s. 12962-12969
-
Tidskriftsartikel (refereegranskat)abstract
- Designing a facile and low-cost methodology to fabricate earth-abundant catalysts is very much needed for a wide range of applications. Herein, a simple and straightforward approach was developed to tune the electronic properties of cobalt oxide nanostructures by doping them with nickel and then using them to catalyze the oxygen evolution reaction (OER) in an aqueous solution of 1.0 M KOH. The addition of a nickel impurity improved the conductivity of the cobalt oxide, and further increased its activity towards the OER. Analytical techniques such as scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and powder X-ray diffraction (XRD) were used to investigate, respectively, the morphology, composition and crystalline structure of the materials used. The nickel-doped cobalt oxide material showed randomly oriented nanowires and a high density of nanoparticles, exhibited the cubic phase, and contained cobalt, nickel and oxygen as its main elements. The nickel-doped cobalt oxide also yielded a Tafel slope of 82 mV dec(-1) and required an overpotential of 300 mV to reach a current density of 10 mA cm(-2). As an OER catalyst, it was shown to be durable for 40 h. Electrochemical impedance spectroscopy (EIS) analysis showed a low charge-transfer resistance of 177.5 ohms for the nickel-doped cobalt oxide, which provided a further example of its excellent OER performance. These results taken together indicated that nickel doping of cobalt oxide can be accomplished via a facile approach and that the product of this doping can be used for energy and environmental applications.
|
|
| 3. |
- Aftab, Umair, et al.
(författare)
-
Mixed CoS2@Co3O4 composite material: An efficient nonprecious electrocatalyst for hydrogen evolution reaction
- 2020
-
Ingår i: International journal of hydrogen energy. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0360-3199 .- 1879-3487. ; 45:27, s. 13805-13813
-
Tidskriftsartikel (refereegranskat)abstract
- Hydrogen evolution reaction (HER) has been identified as a sustainable and environment friendly technology for a wide range of energy conversion and storage applications. The big barrier in realizing this green technology requires a highly efficient, earth-abundant, and low-cost electrocatalyst for HER. Various HER catalysts have been designed and reported, still, their performance is not up to the mark of Pt. Among them, cobalt-based, especially cobalt disulfide (CoS2) has shown significant HER activity and found suitable candidature for HER due to its low cost, simple to prepare, and exhibits good stability. Herein, we synthesized various nanostructured materials including pure CoS2, Co3O4 and their composites by wet chemical methods and found them active for HER. The scanning electron microscopy (SEM) has revealed a morphology of composite as a mixture of nanowires and round shape spherical nanoparticles with several microns in dimension. The X-ray diffraction (XRD) confirmed the cubic phase of CoS2 and cubic phase of Co3O4 in the composite materials. The chemical deposition of CoS2 onto Co3O4 has tailored the HER activity of CoS2@Co3O4 composite material. Two CoS2@Co3O4 composite materials were produced with varying amounts of Co3O4 and labeled as samples 1 and 2. The Co3O4 reduced the adsorption energy for hydrogen, decreased the aggregation of CoS2 and uplifted the stability of CoS2@Co3O4 a composite material in alkaline media. Sample 1 requires an overpotential of 320 mV to reach a current density of 10 mA/cm(2) and it exhibits a Tafel slope of 42 mVdec(-1) which is the key indicator for the fast HER kinetics on sample 1. The sample 1 is highly durable for 50 h and also it has excellent stability. The electrochemical impedance spectroscopy (EIS) revealed a small charge transfer resistance of 28.81 Ohms for the sample 1 with high capacitance double-layer value of 0.81 mF. EIS has supported polarization and Tafel slope results. Based on the partial physical characterization and the electrochemical results, the as-obtained sample 1 (CoS2@Co3O4 composite material) will find potential applications in an extended range of energy conversion and storage devices owing to its low cost, high abundance, and excellent efficiency. (C) 2020 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
|
|
| 4. |
- Aftab, Umair, et al.
(författare)
-
Nickel-cobalt bimetallic sulfide NiCo(2)S(4)nanostructures for a robust hydrogen evolution reaction in acidic media
- 2020
-
Ingår i: RSC Advances. - : Royal Society of Chemistry. - 2046-2069. ; 10:37, s. 22196-22203
-
Tidskriftsartikel (refereegranskat)abstract
- There are many challenges associated with the fabrication of efficient, inexpensive, durable and very stable nonprecious metal catalysts for the hydrogen evolution reaction (HER). In this study, we have designed a facile strategy by tailoring the concentration of precursors to successfully obtain nickel-cobalt bimetallic sulfide (NiCo2S4) using a simple hydrothermal method. The morphology of the newly prepared NiCo(2)S(4)comprised a mixture of microparticles and nanorods, which were few microns in dimension. The crystallinity of the composite sample was found to be excellent with a cubic phase. The sample that contained a higher amount of cobalt compared to nickel and produced single-phase NiCo(2)S(4)exhibited considerably improved HER performance. The variation in the salt precursor concentration during the synthesis of a material is a simple methodology to produce a scalable platinum-free catalyst for HER. The advantageous features of the multiple active sites of cobalt in the CN-21 sample as compared to that for pristine CoS and NiS laid the foundation for the provision of abundant active edges for HER. The composite sample produced a current density of 10 mA cm(-2)at an overpotential of 345 mV. Also, it exhibited a Tafel value of 60 mV dec(-1), which predominantly ensured rapid charge transfer kinetics during HER. CN-21 was highly durable and stable for 30 hours. Electrochemical impedance spectroscopy showed that the charge transfer resistance was 21.88 ohms, which further validated the HER polarization curves and Tafel results. CN-21 exhibited a double layer capacitance of 4.69 mu F cm(-2)and a significant electrochemically active surface area of 134.0 cm(2), which again supported the robust efficiency for HER. The obtained results reveal that our developed NiCo(2)S(4)catalyst has a high density of active edges, and it is a non-noble metal catalyst for the hydrogen evolution reaction. The present findings provide an alternative strategy and an active nonprecious material for the development of energy-related applications.
|
|
| 5. |
- Aftab, Umair, et al.
(författare)
-
The chemically reduced CuO-Co3O4 composite as a highly efficient electrocatalyst for oxygen evolution reaction in alkaline media
- 2019
-
Ingår i: Catalysis Science & Technology. - : ROYAL SOC CHEMISTRY. - 2044-4753 .- 2044-4761. ; 9:22, s. 6274-6284
-
Tidskriftsartikel (refereegranskat)abstract
- The fabrication of efficient, alkaline-stable and nonprecious electrocatalysts for the oxygen evolution reaction is highly needed; however, it is a challenging task. Herein, we report a noble metal-free advanced catalyst, i.e. the chemically reduced mixed transition metal oxide CuO-Co3O4 composite, with outstanding oxygen evolution reaction activity in alkaline media. Sodium borohydride (NaBH4) was used as a reducing agent for the mixed transition metal oxide CuO-Co3O4. The chemically reduced composite carried mixed valence states of Cu and Co, which played a dynamic role in driving an excellent oxygen evolution reaction process. The X-ray photo-electron spectroscopy (XPS) study confirmed high density of active sites in the treated sample with a large number of oxygen vacancies. The developed electrocatalyst showed the lowest overpotential of 144.5 mV vs. the reversible hydrogen electrode (RHE) to achieve the current density of 40 mA cm(-2) and remained stable for 40 hours throughout the chronoamperometry test at the constant potential of 1.39 V vs. RHE. Moreover, the chemically reduced composite was highly durable. Electrochemical impedance spectroscopy (EIS) confirmed the low charge transfer resistance of 13.53 ohms for the chemically reduced composite, which was 50 and 26 times smaller than that of Co3O4 and untreated CuO-Co3O4, respectively. The electrochemically active surface area for the chemically reduced composite was found to be greater than that for pristine CuO, Co3O4 and untreated pristine CuO-Co3O4. These findings reveal the possibility of a new gateway for the capitalization of a chemically reduced sample into diverse energy storage and conversion systems such as lithium-ion batteries and supercapacitors.
|
|
| 6. |
- Aftab, Umair, et al.
(författare)
-
Two step synthesis of TiO2–Co3O4 composite for efficient oxygen evolution reaction
- 2021
-
Ingår i: International journal of hydrogen energy. - : Elsevier. - 0360-3199 .- 1879-3487. ; 46:13, s. 9110-9122
-
Tidskriftsartikel (refereegranskat)abstract
- For an active hydrogen gas generation through water dissociation, the sluggish oxygen evolution reaction (OER) kinetics due to large overpotential is a main hindrance. Herein, a simple approach is used to produce composite material based on TiO2/Co3O4 for efficient OER and overpotential is linearly reduced with increasing amount of TiO2. The scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM) investigations reveal the wire like morphology of composite materials, formed by the self-assembly of nanoparticles. The titania nanoparticles were homogenously distributed on the larger Co3O4 nanoparticles. The powder x-ray diffraction revealed a tetragonal phase of TiO2 and the cubic phase of Co3O4 in the composite materials. Composite samples with increasing TiO2 content were obtained (18%, 33%, 41% and 65% wt.). Among the composites, cobalt oxide-titanium oxide with the highest TiO2 content (CT-20) possesses the lowest overpotential for OER with a Tafel slope of 60 mV dec−1 and an exchange current density of 2.98 × 10−3A/cm2. The CT-20 is highly durable for 45 h at different current densities of 10, 20 and 30 mA/cm2. Electrochemical impedance spectroscopy (EIS) confirmed the fast charge transport for the CT-20 sample, which potentially accelerated the OER kinetics. These results based on a two-step methodology for the synthesis of TiO2/Co3O4 material can be useful and interesting for various energy storage and energy conversion systems.
|
|
| 7. |
- Solangi, Muhammad Yameen, et al.
(författare)
-
In-situ growth of nonstoichiometric CrO0.87 and Co3O4 hybrid system for the enhanced electrocatalytic water splitting in alkaline media
- 2023
-
Ingår i: International journal of hydrogen energy. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0360-3199 .- 1879-3487. ; 48:93, s. 36439-36451
-
Tidskriftsartikel (refereegranskat)abstract
- The development of electrocatalysts for electrochemical water splitting has received considerable attention in response to the growing demand for renewable energy sources and environmental concerns. In this study, a simple hydrothermal growth approach was developed for the in-situ growth of non-stoichiometric CrO0.87 and Co3O4 hybrid materials. It is apparent that the morphology of the prepared material shows a heterogeneous aggregate of irregularly shaped nanoparticles. Both CrO0.87 and Co3O4 have cubic crystal structures. Its chemical composition was governed by the presence of Co, Cr, and O as its main constituents. For understanding the role CrO0.87 plays in the half-cell oxygen evolu-tion reaction (OER) in alkaline conditions, CrO0.87 was optimized into Co3O4 nanostructures. The hybrid material with the highest concentration of CrO0.87 was found to be highly efficient at driving OER reactions at 255 mV and 20 mA cm(-2). The optimized material demonstrated excellent durability for 45 h and a Tafel slope of 56 mV dec(-1). Several factors may explain the outstanding performance of CrO0.87 and Co3O4 hybrid materials, including multiple metallic oxidation states, tailored surface properties, fast charge transport, and surface defects. An alternative method is proposed for the preparation of new generations of electrocatalysts for the conversion and storage of energy. (c) 2023 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
|
|
| 8. |
- Ahmed Khand, Aftab, et al.
(författare)
-
Synthesis of Sheet Like Nanostructures of NiO Using Potassium Dichromate as Surface Modifying Agent for the Sensitive and Selective Determination of Amlodipine Besylate (ADB) Drug
- 2021
-
Ingår i: Electroanalysis. - : WILEY-V C H VERLAG GMBH. - 1040-0397 .- 1521-4109. ; 33:5, s. 1121-1128
-
Tidskriftsartikel (refereegranskat)abstract
- The monitoring of hypertension drugs is very critical and important to sustain a healthy life. In this study, we have synthesized nickel oxide (NiO) nanostructures using potassium dichromate as surface modifying agent by hydrothermal method. These NiO nanostructures were found highly active for the oxidation of ADB besylate (ADB). The unit cell structure and morphology were investigated by scanning electron microscopy (SEM) and powder X-ray diffraction (XRD) techniques. The SEM study has confirmed the nano sheet like morphology and XRD analysis has described the cubic unit arrays of NiO. After the physical characterization, NiO nanostructures were used to modify the surface of glassy carbon electrode (GCE) by drop casting method. Then cyclic voltammetry (CV) was used to characterize the electrochemical activity of NiO nanostructures in the0.1 M phosphate buffer solution of pH 10.0 and a well resolved oxidation peak was identified at 0.70 V. The linear range for the NiO nanostructures was observed from 20-90 nM with a regression coefficient of 0.99 using CV. The calculated limit of detection (LOD) was 2.125 nM and the limit of quantification (LOQ) was 4.08 nM. Further to validate the CV calibration plot, an amperometry experiment was performed on the NiO nanostructures and sensors exhibited a linear range of 10 nM to 115 nM with LOD of 1.15 nM. The proposed approach was successfully used for the determination of ADB from commercial tablets and it reveals that the sensor could be capitalized to monitor ADB concentrations from pharmaceutical products. The use of potassium dichromate as a surface modifying agent for the metal oxide nanostructures may be of great interest to manipulate their crystal and surface properties for the extended range of biomedical and energy related applications.
|
|
| 9. |
- Ali Soomro, Razium, et al.
(författare)
-
Controlled synthesis and electrochemical application of skein-shaped NiO nanostructures
- 2015
-
Ingår i: Journal of Solid State Electrochemistry. - : Springer Verlag (Germany). - 1432-8488 .- 1433-0768. ; 19:3, s. 913-922
-
Tidskriftsartikel (refereegranskat)abstract
- A simple, economical and mild solution chemistry method was used to synthesize diverse nickel oxide (NiO) nanostructures employing methionine as a growth-directing agent. The as-synthesized NiO nanostructures were observed to possess a unique skein-shape morphology with uniform spherical distribution. The NiO nanoskein (NiO NSk) formation was extensively studied using X-ray diffraction (XRD), X-ray photoelectron microscopy (XPS), scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) techniques, respectively. The unique NiO NSks exhibited better electrocatalytic activity towards glucose oxidation in alkaline media, enabling the development of a highly sensitive non-enzymatic glucose sensor. The observed analytical properties included high sensitivity (1915 mu A mM(-1) cm(-2)), wide linear range (0.1-5.0 mM), low detection limit (0.7 mu M), higher stability and reproducibility. Moreover, the sensor is selective in the presence of interfering species such as ascorbic acid (AA), uric acid (UA) and dopamine (DP) during the non-enzymatic glucose sensing. The worthy-of-notice electrocatalytic activity and economical feasible preparation of NiO NSk-shaped electroactive material for direct glucose-sensing applications make the present study of high interest for the fabrication of low-cost devices. A NiO NSk-based glucose sensor has also been employed for glucose determination in human serum with adequate results, suggesting high potential for the routine monitoring of glucose from biotechnology, clinical and food industry samples.
|
|
| 10. |
- Ali Soomro, Razium, et al.
(författare)
-
Development of sensitive non-enzymatic glucose sensor using complex nanostructures of cobalt oxide
- 2015
-
Ingår i: Materials Science in Semiconductor Processing. - : Elsevier. - 1369-8001 .- 1873-4081. ; 34, s. 373-381
-
Tidskriftsartikel (refereegranskat)abstract
- The study reports the synthesis of cobalt oxide (Co3O4) nanostructures and their application in enzyme free electrochemical sensing of glucose. The synthesized nanostructures were elaborately characterized via number of analytical techniques including scanning electron microscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The as-synthesized nanostructures of Co3O4 were found to exhibited nanodisc like morphology with the size dimension in range of 300-500 nm. The obtained morphological features were evaluated for their electrochemical potential towards oxidation of glucose which enabled development of sensitive (27.33 mu A mM(-1) cm(-2)), and stable enzyme free glucose sensor. In addition, the developed sensor showed excellent linearity (r(2)=0.9995), wide detection range (0.5-5.0 mM), lower detection limit (0.8 mu M) and extreme selectivity towards glucose in the presence of common interferents like dopamine (DP), ascorbic acid (AA) and uric acid (UA). The successfully application of developed sensor for real blood glucose analysis further reflects its capability for routine glucose measurement.
|
|
