| 1. |
- Aguilar-Mamani, Wilson, et al.
(författare)
-
Solution-mediated growth of NBA-ZSM-5 crystals retarded by gel entrapment
- 2018
-
Ingår i: Journal of Crystal Growth. - : Elsevier. - 0022-0248 .- 1873-5002. ; 487, s. 57-64
-
Tidskriftsartikel (refereegranskat)abstract
- The synthesis of flat tablet-shaped ZSM-5 crystals from a gel using metakaolin as aluminosilicate source and n-butyl amine as structure directing agent was investigated. The evolution inside the solid phase was characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, thermogravimetry and mass spectrometry. A kinetic study indicated that the nucleation of the majority crystals occurred concurrently with the formation of the gel upon heating the starting liquid suspension. Microstructural evidences undeniably showed that the gel precipitated on ZSM-5 crystals and mineral impurities originating from kaolin. As a result, crystal growth was retarded by gel entrapment, as indicated by the configuration and morphology of the embedded crystals. The results presented herein are harmonized with a solution-mediated nucleation and growth mechanism. Our observations differ from the autocatalytic model that suggests that the nuclei rest inside the gel until released when the gel is consumed. Our results show instead that it is crystals that formed in an early stage before entrapment inside the gel that rest inside the gel until exposed at the gel surface. These results illustrate the limitation of the classical method used in the field to determine nucleation profiles when the crystals become trapped inside the gel.
|
|
| 2. |
- Akhtar, Farid, et al.
(författare)
-
A new kind of age hardenable martensitic stainless steel with high strength and toughness
- 2007
-
Ingår i: Ironmaking & steelmaking. - 0301-9233 .- 1743-2812. ; 34:4, s. 285-289
-
Tidskriftsartikel (refereegranskat)abstract
- Following analysis of typical age hardenable martensitic stainless steels, a new kind of maragingstainless was developed. The new maraging stainless steel showed high strength, ultimate tensilestrength (UTS) 5 1670 MPa, high toughness, K IC 5 83·9 MPa m1/2 and hardness as high as 478 HVin the age hardened condition. Microstructural study with an optical and transmission electron microscope revealed the typical microstructure of age hardenable stainless steel containing lathmartensite and precipitates. TixNi precipitates were identified by transmission electron microscopy, which were responsible for the increase in mechanical properties after age hardening. The results of natural salt spray test showed that the corrosion resistance of new maraging stainless steel approached to the corrosion resistance of 304L stainless steel.
|
|
| 3. |
- Akhtar, Farid
(författare)
-
A new method to process high strength TiCN stainless steel matrix composites
- 2007
-
Ingår i: Powder Metallurgy. - 0032-5899 .- 1743-2901. ; 50:3, s. 250-254
-
Tidskriftsartikel (refereegranskat)abstract
- Layered composites of Ti(C, N) reinforcements and stainless steel have been prepared successfully by powder technology. The layer composite consisted of two layers. The upper layer consisted of TiCN reinforcements and stainless steel as binder material. The lower layer was entirely of binder material (stainless steel). The micro structural study revealed that the upper layer (TiCN/465 stainless steel) showed core–rim microstructure of conventional cermets and the lower layer showed the structure of sintered steel. An intermediate layer was formed due to diffusion reaction of upper and lower layers. This intermediate layer showed a gradient microstructure. The bending strength of the layered material measured was remarkably higher. Ninety per cent increase in the bending strength in the case of 50 wt-% reinforcement in the upper layer was found. The fracture morphologies of upper, lower and intermediate layers are also reported
|
|
| 4. |
|
|
| 5. |
- Akhtar, Farid, et al.
(författare)
-
A study of the sintering of diatomaceous earth to produce porous ceramic monolithswith bimodal porosity and high strength
- 2010
-
Ingår i: Powder Technology. - Amsterdam, Netherlands : Elsevier B.V.. - 0032-5910 .- 1873-328X. ; 201, s. 253-257
-
Tidskriftsartikel (refereegranskat)abstract
- Diatomite powder, a naturally occurring porous raw material, was used to fabricate ceramic materials withbimodal porosity and high strength. The effect of the sintering temperature on the density and porosity ofdry pressed diatomite green bodies was evaluated using mercury porosimetry and water immersionmeasurements. It was found that the intrinsic porosity of the diatomite particles with a pore size around0.2 μm was lost at sintering temperatures above 1200 °C. Maintaining the sintering temperature at around1000 °C resulted in highly porous materials that also displayed a high compressive strength. Microstructuralstudies by scanning electron microscopy and energy-dispersive X-ray analysis suggested that the porecollapse was facilitated by the presence of low melting impurities like Na2O and K2O.
|
|
| 6. |
|
|
| 7. |
- Akhtar, Farid, et al.
(författare)
-
Aluminophosphate monoliths with high CO2-over-N2 selectivity and CO2 capture capacity
- 2014
-
Ingår i: RSC Advances. - : Royal Society of Chemistry (RSC). - 2046-2069. ; 4:99, s. 55877-55883
-
Tidskriftsartikel (refereegranskat)abstract
- Monoliths of microporous aluminophosphates (AlPO4-17 and AlPO4-53) were structured by binder-free pulsed current processing. Such monoliths could be important for carbon capture from flue gas. The AlPO4-17 and AlPO4-53 monoliths exhibited a tensile strength of 1.0 MPa and a CO2 adsorption capacity of 2.5 mmol g-1 and 1.6 mmol g-1, respectively at 101 kPa and 0°C. Analyses of single component CO2 and N2 adsorption data indicated that the AlPO4-53 monoliths had an extraordinarily high CO2-over-N2 selectivity from a binary gas mixture of 15 mol% CO2 and 85 mol% N2. The estimated CO2 capture capacity of AlPO4-17 and AlPO4-53 monoliths in a typical pressure swing adsorption (PSA) process at 20°C was higher than that of the commonly used zeolite 13X granules. Under cyclic sorption conditions, AlPO4-17 and AlPO4-53 monoliths were regenerated by lowering the pressure of CO2. Regeneration was done without application of heat, which would regenerate them to their full capacity for CO2 adsorption.
|
|
| 8. |
- Akhtar, Farid
(författare)
-
An investigation on the solid state sintering of mechanically alloyed nano-structured 90W--Ni--Fe tungsten heavy alloy
- 2008
-
Ingår i: International journal of refractory metals & hard materials. - : Elsevier BV. - 0263-4368. ; 26:3, s. 145-151
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, 90W–7Ni–3Fe heavy alloy was investigated for its microstructure development, mechanical properties and fracture behavior after solid state sintering. The nano-sized powders were synthesized by mechanical alloying (MA). The microstructure of solid state sintered heavy alloys consisted of tungsten matrix. The average tungsten grain size in the range of 1.7–3.0 μm was obtained. It was found that the grain size largely affected the mechanical properties. Tensile strength more than 1200 MPa was achieved at a sintering temperature of 1350 °C. Fracture mechanisms based on microscopical observations on the fracture surfaces were studied. Matrix failure, tungsten-intergranular cleavage and tungsten–matrix interfacial separation were found to be the possible failure mechanisms.
|
|
| 9. |
|
|
| 10. |
- Akhtar, Farid
(författare)
-
Ceramic reinforced high modulus steel composites : processing, microstructure and properties
- 2014
-
Ingår i: Canadian metallurgical quarterly. - 0008-4433 .- 1879-1395. ; 53:3, s. 253-263
-
Tidskriftsartikel (refereegranskat)abstract
- Ceramic reinforced steel matrix composites are materials for automotive, aerospace, wear and cutting applications. Such metal matrix composites (MMCs) combine attractive physical, mechanical and wear properties with ease of fabrication and low cost. The review focuses on the current state of the art of producing these metal matrix composites, ceramics reinforcements, composition of steel matrix, microstructure evolution and parameters influencing the mechanical and wear properties. Processing methods to fabricate ceramic reinforced steel matrix composites are discussed to produce these composites with low number of defects, homogeneous microstructure and high mechanical and wear performance. The influence of chemical nature of ceramic reinforcements and composition of steel matrix on the microstructure, mechanical and wear properties is presented. The strengthening mechanisms and parameters controlling wear performance of steel MMCs are described as a function of the content of ceramic reinforcements, microstructural design and structure of the steel matrix. Keeping in view the stability of ceramics in steels, suitable ceramic reinforcements and steel matrix materials are discussed. Moreover, the importance of microstructure and interface between ceramic reinforcement and steel matrix in controlling the mechanical properties of steel MMCs is highlighted. The review identifies area of research for development to fully appreciate and tailor the properties of these industrially important composites.
|
|
