| 1. |
- Jacobsson, Jesper, 1984-, et al.
(författare)
-
An open-access database and analysis tool for perovskite solar cells based on the FAIR data principles
- 2022
-
Ingår i: Nature Energy. - : Springer Nature. - 2058-7546. ; 7:1, s. 107-115
-
Tidskriftsartikel (refereegranskat)abstract
- Large datasets are now ubiquitous as technology enables higher-throughput experiments, but rarely can a research field truly benefit from the research data generated due to inconsistent formatting, undocumented storage or improper dissemination. Here we extract all the meaningful device data from peer-reviewed papers on metal-halide perovskite solar cells published so far and make them available in a database. We collect data from over 42,400 photovoltaic devices with up to 100 parameters per device. We then develop open-source and accessible procedures to analyse the data, providing examples of insights that can be gleaned from the analysis of a large dataset. The database, graphics and analysis tools are made available to the community and will continue to evolve as an open-source initiative. This approach of extensively capturing the progress of an entire field, including sorting, interactive exploration and graphical representation of the data, will be applicable to many fields in materials science, engineering and biosciences.
|
|
| 2. |
- Becker, Pascal, et al.
(författare)
-
Low Temperature Synthesis of Stable γ-CsPbI 3 Perovskite Layers for Solar Cells Obtained by High Throughput Experimentation
- 2019
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6832 .- 1614-6840. ; 9:22
-
Tidskriftsartikel (refereegranskat)abstract
- The structural phases and optoelectronic properties of coevaporated CsPbI 3 thin films with a wide range of [CsI]/[PbI 2 ] compositional ratios are investigated using high throughput experimentation and gradient samples. It is found that for CsI-rich growth conditions, CsPbI 3 can be synthesized directly at low temperature into the distorted perovskite γ-CsPbI 3 phase without detectable secondary phases. In contrast, PbI 2 -rich growth conditions are found to lead to the non-perovskite δ-phase. Photoluminescence spectroscopy and optical-pump THz-probe mapping show carrier lifetimes larger than 75 ns and charge carrier (sum) mobilities larger than 60 cm 2 V −1 s −1 for the γ-phase, indicating their suitability for high efficiency solar cells. The dependence of the carrier mobilities and luminescence peak energy on the Cs-content in the films indicates the presence of Schottky defect pairs, which may cause the stabilization of the γ-phase. Building on these results, p–i–n type solar cells with a maximum efficiency exceeding 12% and high shelf stability of more than 1200 h are demonstrated, which in the future could still be significantly improved, judging on their bulk optoelectronic properties.
|
|
| 3. |
- Dagar, Janardan, et al.
(författare)
-
Compositional and Interfacial Engineering Yield High-Performance and Stable p-i-n Perovskite Solar Cells and Mini-Modules
- 2021
-
Ingår i: ACS applied materials & interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 13:11, s. 13022-13033
-
Tidskriftsartikel (refereegranskat)abstract
- Through the optimization of the perovskite precursor composition and interfaces to selective contacts, we achieved a p-i-n-type perovskite solar cell (PSC) with a 22.3% power conversion efficiency (PCE). This is a new performance record for a PSC with an absorber bandgap of 1.63 eV. We demonstrate that the high device performance originates from a synergy between (1) an improved perovskite absorber quality when introducing formamidinium chloride (FACl) as an additive in the "triple cation" Cs0.05FA0.79MA0.16PbBr0.51I2.49 (Cs-MAFA) perovskite precursor ink, (2) an increased open-circuit voltage, VOC, due to reduced recombination losses when using a lithium fluoride (LiF) interfacial buffer layer, and (3) high-quality hole-selective contacts with a self-assembled monolayer (SAM) of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) on ITO electrodes. While all devices exhibit a high performance after fabrication, as determined from current-density voltage, J-V, measurements, substantial differences in device performance become apparent when considering longer-term stability data. A reduced long-term stability of devices with the introduction of a LiF interlayer is compensated for by using FACl as an additive in the metal-halide perovskite thin-film deposition. Optimized devices maintained about 80% of the initial average PCE during maximum power point (MPP) tracking for >700 h. We scaled the optimized device architecture to larger areas and achieved fully laser patterned series-interconnected mini-modules with a PCE of 19.4% for a 2.2 cm2 active area. A robust device architecture and reproducible deposition methods are fundamental for high performance and stable large-area single junction and tandem modules based on PSCs.
|
|
