| 1. |
|
|
| 2. |
- Lindblad, Rebecka, 1984-
(författare)
-
Electronic Structures and Energy Level Alignment in Mesoscopic Solar Cells : A Hard and Soft X-ray Photoelectron Spectroscopy Study
- 2014
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Photoelectron spectroscopy is an experimental method to study the electronic structure in matter. In this thesis, a combination of soft and hard X-ray based photoelectron spectroscopy has been used to obtain atomic level understanding of electronic structures and energy level alignments in mesoscopic solar cells. The thesis describes how the method can be varied between being surface and bulk sensitive and how to follow the structure linked to particular elements. The results were discussed with respect to the material function in mesoscopic solar cell configurations.The heart of a solar cell is the charge separation of photoexcited electrons and holes, and in a mesoscopic solar cell, this occurs at interfaces between different materials. Understanding the energy level alignment between the materials is important for developing the function of the device. In this work, it is shown that photoelectron spectroscopy can be used to experimentally follow the energy level alignment at interfaces such as TiO2/metal sulfide/polymer, as well as TiO2/perovskite.The electronic structures of two perovskite materials, CH3NH3PbI3 and CH3NH3PbBr3 were characterized by photoelectron spectroscopy and the results were discussed with support from quantum chemical calculations. The outermost levels consisted mainly of lead and halide orbitals and due to a relatively higher cross section for heavier elements, hard X-ray excitation was shown useful to study the position as well as the orbital character of the valence band edge.Modifications of the energy level positions can be followed by core level shifts. Such studies showed that a commonly used additive in mesoscopic solar cells, Li-TFSI, affected molecular hole conductors in the same way as a p-dopant. A more controlled doping can also be achieved by redox active dopants such as Co(+III) complexes and can be studied quantitatively with photoelectron spectroscopy methods.Hard X-rays allow studies of hidden interfaces, which were used to follow the oxidation of Ti in stacks of thin films for conducting glass. By the use of soft X-rays, the interface structure and bonding of dye molecules to mesoporous TiO2 or ZnO could be studied in detail. A combination of the two methods can be used to obtain a depth profiling of the sample.
|
|
| 3. |
- Platzer Björkman, Charlotte, 1976-, et al.
(författare)
-
Back and front contacts in kesterite solar cells : state-of-the-art and open questions
- 2019
-
Ingår i: Journal of Physics. - : Institute of Physics Publishing (IOPP). - 2515-7655. ; 1:4
-
Tidskriftsartikel (refereegranskat)abstract
- We review the present state-of-the-art within back and front contacts in kesterite thin film solar cells, as well as the current challenges. At the back contact, molybdenum (Mo) is generally used, and thick Mo(S, Se)2 films of up to several hundred nanometers are seen in record devices, in particular for selenium-rich kesterite. The electrical properties of Mo(S, Se)2 can vary strongly depending on orientation and indiffusion of elements from the device stack, and there are indications that the back contact properties are less ideal in the sulfide as compared to the selenide case. However, the electronic interface structure of this contact is generally not well-studied and thus poorly understood, and more measurements are needed for a conclusive statement. Transparent back contacts is a relatively new topic attracting attention as crucial component in bifacial and multijunction solar cells. Front illuminated efficiencies of up to 6% have so far been achieved by adding interlayers that are not always fully transparent. For the front contact, a favorable energy level alignment at the kesterite/CdS interface can be confirmed for kesterite absorbers with an intermediate [S]/([S]+[Se]) composition. This agrees with the fact that kesterite absorbers of this composition reach highest efficiencies when CdS buffer layers are employed, while alternative buffer materials with larger band gap, such as Cd1−x Zn x S or Zn1−x Sn x O y , result in higher efficiencies than devices with CdS buffers when sulfur-rich kesterite absorbers are used. Etching of the kesterite absorber surface, and annealing in air or inert atmosphere before or after buffer layer deposition, has shown strong impact on device performance. Heterojunction annealing to promote interdiffusion was used for the highest performing sulfide kesterite device and air-annealing was reported important for selenium-rich record solar cells.
|
|
| 4. |
- Wilks, Regan G., et al.
(författare)
-
Dynamic Effects and Hydrogen Bonding in Mixed-Halide Perovskite Solar Cell Absorbers
- 2021
-
Ingår i: The Journal of Physical Chemistry Letters. - : American Chemical Society (ACS). - 1948-7185. ; 12:16, s. 3885-3890
-
Tidskriftsartikel (refereegranskat)abstract
- The organic component (methylammonium) of CH3NH3PbI3-xClx-based perovskites shows electronic hybridization with the inorganic framework via H-bonding between N and I sites. Femtosecond dynamics induced by core excitation are shown to strongly influence the measured X-ray emission spectra and the resonant inelastic soft X-ray scattering of the organic components. The N K core excitation leads to a greatly increased N-H bond length that modifies and strengthens the interaction with the inorganic framework compared to that in the ground state. The study indicates that excited-state dynamics must be accounted for in spectroscopic studies of this perovskite solar cell material, and the organic-inorganic hybridization interaction suggests new avenues for probing the electronic structure of this class of materials. It is incidentally shown that beam damage to the methylamine component can be avoided by moving the sample under the soft X-ray beam to minimize exposure and that this procedure is necessary to prevent the creation of experimental artifacts.
|
|
