| 1. |
- Gardner, T. A., et al.
(författare)
-
Transparency and sustainability in global commodity supply chains
- 2019
-
Ingår i: World Development. - : Elsevier BV. - 0305-750X .- 1873-5991. ; 121, s. 163-177
-
Tidskriftsartikel (refereegranskat)abstract
- Over the last few decades rapid advances in processes to collect, monitor, disclose, and disseminate information have contributed towards the development of entirely new modes of sustainability governance for global commodity supply chains. However, there has been very little critical appraisal of the contribution made by different transparency initiatives to sustainability and the ways in which they can (and cannot)influence new governance arrangements. Here we seek to strengthen the theoretical underpinning of research and action on supply chain transparency by addressing four questions: (1)What is meant by supply chain transparency? (2)What is the relevance of supply chain transparency to supply chain sustainability governance? (3)What is the current status of supply chain transparency, and what are the strengths and weaknesses of existing initiatives? and (4)What propositions can be advanced for how transparency can have a positive transformative effect on the governance interventions that seek to strengthen sustainability outcomes? We use examples from agricultural supply chains and the zero-deforestation agenda as a focus of our analysis but draw insights that are relevant to the transparency and sustainability of supply chains in general. We propose a typology to distinguish among types of supply chain information that are needed to support improvements in sustainability governance, and illustrate a number of major shortfalls and systematic biases in existing information systems. We also propose a set of ten propositions that, taken together, serve to expose some of the potential pitfalls and undesirable outcomes that may result from (inevitably)limited or poorly designed transparency systems, whilst offering guidance on some of the ways in which greater transparency can make a more effective, lasting and positive contribution to sustainability.
|
|
| 2. |
- López-Dekker, P., et al.
(författare)
-
BIOMASS end-to-end mission performance assessment
- 2012
-
Ingår i: Proc. IGARSS 2012, IEEE International Geoscience and Remote Sensing Symposium, Munich, Germany, 22-27 July 2012. - 2153-6996. - 9781467311588 ; , s. 1602-1605
-
Konferensbidrag (refereegranskat)abstract
- This paper provides an overview of the BIOMASS Mission End-to-End simulator (BEES) and of the mission performance analysis performed with it. The end-to-end performance, in terms of biomass estimates error, is close to the 20% error goal set for the mission. The main sources of errors are temporal decorrelation and the limited available bandwidth, while system induced errors have a negligible impact on the final performance.
|
|
| 3. |
- López-Dekker, P., et al.
(författare)
-
BIOMASS End-to-End performance Simulator
- 2011
-
Ingår i: IEEE International Geoscience and Remote Sensing Symposium, IGARSS 2011. Vancouver, 24-29 July 2011. - 9781457710049 ; , s. 4249-4252
-
Konferensbidrag (refereegranskat)abstract
- This paper discusses the implementation of an end-to-end simulator for the BIOMASS mission. An overview of the system architecture is provided along with a functional description of the modules that comprise the simulator.
|
|
| 4. |
- Bolelli, G., et al.
(författare)
-
Sliding and abrasive wear behaviour of HVOF- and HVAF-sprayed Cr3C2-NiCr hardmetal coatings
- 2016
-
Ingår i: Wear. - : Elsevier BV. - 0043-1648 .- 1873-2577. ; 358-359, s. 32-50
-
Tidskriftsartikel (refereegranskat)abstract
- This paper provides a comprehensive characterisation of HVOF- and HVAF-sprayed Cr3C2–25 wt.% NiCr hardmetal coatings. One commercial powder composition with two different particle size distributions was processed using five HVOF and HVAF thermal spray systems.All coatings contain less Cr3C2 than the feedstock powder, possibly due to the rebound of some Cr3C2-rich particles during high-velocity impact onto the substrate.Dry sand-rubber wheel abrasive wear testing causes both grooving and pull-out of splat fragments. Mass losses depend on inter- and intra-lamellar cohesion, being higher (≥70 mg after a wear distance of 5904 m) for the coatings deposited with the coarser feedstock powder or with one type of HVAF torch.Sliding wear at room temperature against alumina involves shallower abrasive grooving, small-scale delamination and carbide pull-outs, and it is controlled by intra-lamellar cohesion. The coatings obtained from the fine feedstock powder exhibit the lowest wear rates (≈5x10−6 mm3/(Nm)). At 400 °C, abrasive grooving dominates the sliding wear behaviour; wear rates increase by one order of magnitude but friction coefficients decrease from ≈0.7 to ≈0.5. The thermal expansion coefficient of the coatings (11.08x10−6 °C−1 in the 30–400 °C range) is sufficiently close to that of the steel substrate (14.23x10−6 °C−1) to avoid macro-cracking
|
|
| 5. |
- Bolelli, G., et al.
(författare)
-
Tribology of HVOF- and HVAF-sprayed WC-10Co4Cr hardmetal coatings : A comparative assessment
- 2015
-
Ingår i: Surface and Coatings Technology. - : Elsevier. - 0257-8972. ; 265, s. 125-144
-
Tidskriftsartikel (refereegranskat)abstract
- his paper provides a comprehensive assessment of the sliding and abrasive wear behaviour of WC–10Co4Cr hardmetal coatings, representative of the existing state-of-the-art. A commercial feedstock powder with two different particle size distributions was sprayed onto carbon steel substrates using two HVOF and two HVAF spray processes.Mild wear rates of < 10-7 mm3/(Nm) and friction coefficients of ≈ 0.5 were obtained for all samples in ball-on-disk sliding wear tests at room temperature against Al2O3 counterparts. WC–10Co4Cr coatings definitely outperform a reference electrolytic hard chromium coating under these test conditions. Their wear mechanisms include extrusion and removal of the binder matrix, with the formation of a wavy surface morphology, and brittle cracking. The balance of such phenomena is closely related to intra-lamellar features, and rather independent of those properties (e.g. indentation fracture toughness, elastic modulus) which mainly reflect large-scale inter-lamellar cohesion, as quantitatively confirmed by a principal component analysis. Intra-lamellar dissolution of WC into the matrix indeed increases the incidence of brittle cracking, resulting in slightly higher wear rates. At 400 °C, some of the hardmetal coatings fail because of the superposition between tensile residual stresses and thermal expansion mismatch stresses (due to the difference between the thermal expansion coefficients of the steel substrate and of the hardmetal coating). Those which do not fail, on account of lower residual stresses, exhibit higher wear rates than at room temperature, due to oxidation of the WC grains.The resistance of the coatings against abrasive wear, assessed by dry sand–rubber wheel testing, is related to inter-lamellar cohesion, as proven by a principal component analysis of the collected dataset. Therefore, coatings deposited from coarse feedstock powders suffer higher wear loss than those obtained from fine powders, as brittle inter-lamellar detachment is caused by their weaker interparticle cohesion, witnessed by their systematically lower fracture toughness as well.
|
|
| 6. |
|
|
