| 1. |
- Besharat, Zahra
(författare)
-
Adsorption of molecular thin films on metal and metal oxide surfaces
- 2016
-
Konstnärligt arbete (övrigt vetenskapligt/konstnärligt)abstract
- Metal and metal oxides are widely used in industry, and to optimize their performance their surfaces are commonly functionalized by the formation of thin films. Self-assembled monolayers (SAMs) are deposited on metals or metal oxides either from solution or by gas deposition. Thiols with polar terminal groups are utilized for creating the responsive surfaces which can interact electrostatically with other adsorbates. Surface charge effects wetting and adhesion, and many other surface properties. Polar terminal groups in thiols could be used to modify these factors. Mixed SAMs can provide more flexible surfaces, and could change the resulting surface properties under the influence of factors such as pH, temperature, and photo-illumination. Therefore, in order to control these phenomena by mixed polar-terminated thiols, it is necessary to understand the composition and conformation of the mixed SAMs and their response to these factors. In this work, mixtures of thiols with carboxylic and amino terminal groups were studied. Carboxylic and amino terminal groups of thiol interact with each other via hydrogen bonding in solution and form a complex. Complexes adsorb to the surface in non-conventional orientations. Unmixed SAMs from each type, either carboxylic terminated thiols or amino terminated thiols are in standing up orientation while SAMs from complexes are in an axially in-plane orientation. Selenol is an alternative to replace thiols for particular applications such as contact with biological matter which has a better compatibility with selenol than sulfur. However, the Se-C bond is weaker than the S-C bond which limits the application of selenol. Understanding the selenol adsorption mechanism on gold surfaces could shed some light on Se-C cleavage and so is investigated in this work. Se-C cleavage happens in the low coverage areas on the step since atoms at steps have lower coordination making them more reactive than atoms on the terraces. Another area where the self-assembly of molecules is of importance is for dye sensitized solar cells, which are based on the adsorption of the dye onto metal oxides surfaces such as TiO2.The interface between the SAM of dye and the substrate is an important factor to consider when designing dyes and surfaces in dye sensitized solar cells (DSSCs). The quality of the self-assembled monolayers of the dye on the TiO2 surface has a critical influence on the efficiency of the DSSCs. Creation of just a monolayer of dye on the surface could lead to an efficient current of photo-excited electrons to the TiO2 and degeneration of the dye by redox. This work, T-PAC dye showed island growth with some ad-layer that is not in contact with the surface, whereas the MP13 dye adsorption is laminar growth. Cuprite (Cu2O) is the initial and most common corrosion product for copper under atmospheric conditions. Copper could be a good replacement for noble metal as catalysts for methanol dehydrogenation. Knowledge about the structure of Cu2O(100) and Cu2O(111) surfaces could be used to obtain a deeper understanding of methanol dehydrogenation mechanisms with respect to adsorption sites on the surfaces. In this work, a detailed study was done of Cu2O(100) surface which revealed the possible surface structures as the result of different preparation conditions. Studies of the structure of Cu2O(100) and Cu2O(111) surfaces show that Cu2O(100) has a comparatively stable surface and reduces surface reactivity. As a consequence, dehydrogenation of methanol is more efficient on the Cu2O(111) surface. The hydrogen produced from methanol dehydrogenation is stored in oxygen adatom sites on both surfaces.
|
|
| 2. |
|
|
| 3. |
- Besharat, Zahra, et al.
(författare)
-
Dehydrogenation of methanol on Cu2O(100) and (111)
- 2017
-
Ingår i: Journal of Chemical Physics. - : AIP Publishing. - 0021-9606 .- 1089-7690. ; 146:24
-
Tidskriftsartikel (refereegranskat)abstract
- Adsorption and desorption of methanol on the (111) and (100) surfaces of Cu2O have been studied using high-resolution photoelectron spectroscopy in the temperature range 120-620 K, in combination with density functional theory calculations and sum frequency generation spectroscopy. The bare (100) surface exhibits a (3,0; 1,1) reconstruction but restructures during the adsorption process into a Cu-dimer geometry stabilized by methoxy and hydrogen binding in Cu-bridge sites. During the restructuring process, oxygen atoms from the bulk that can host hydrogen appear on the surface. Heating transforms methoxy to formaldehyde, but further dehydrogenation is limited by the stability of the surface and the limited access to surface oxygen. The (root 3 x root 3)R30 degrees-reconstructed (111) surface is based on ordered surface oxygen and copper ions and vacancies, which offers a palette of adsorption and reaction sites. Already at 140 K, a mixed layer of methoxy, formaldehyde, and CHxOy is formed. Heating to room temperature leaves OCH and CHx. Thus both CH-bond breaking and CO-scission are active on this surface at low temperature. The higher ability to dehydrogenate methanol on (111) compared to (100) is explained by the multitude of adsorption sites and, in particular, the availability of surface oxygen.
|
|
| 4. |
|
|
| 5. |
- Besharat, Zahra, et al.
(författare)
-
In-situ evaluation of dye adsorption on TiO2 using QCM
- 2017
-
Ingår i: EPJ Photovoltaics. - : EDP Sciences. - 2105-0716. ; 8
-
Tidskriftsartikel (refereegranskat)abstract
- We measured the adsorption characteristics of two organic dyes; triphenylamine-cyanoacrylic acid (TPA-C) and phenoxazine (MP13), on TiO2, directly in a solution based on quartz crystal microbalance (QCM). Monitoring the adsorbed amount as a function of dye concentration and during rinsing allows determination of the equilibrium constant and distinction between chemisorbed and physisorbed dye. The measured equilibrium constants are 0.8 mM(-1) for TPA-C and 2.4 mM(-1) for MP13. X-ray photoelectron spectroscopy was used to compare dried chemisorbed layers of TPA-C prepared in solution with TPA-C layers prepared via vacuum sublimation; the two preparation methods render similar spectra except a small contribution of water residues (OH) on the solution prepared samples. Quantitative Nanomechanical Mapping Atomic Force Microscopy (QNM-AFM) shows that physisorbed TPA-C layers are easily removed by scanning the tip across the surface. Although not obvious in height images, adhesion images clearly demonstrate removal of the dye.
|
|
| 6. |
- Besharat, Zahra, et al.
(författare)
-
Mixed monolayers of alkane thiols with polar terminal group on gold : Investigation of structure dependent surface properties
- 2016
-
Ingår i: Journal of Colloid and Interface Science. - : Elsevier BV. - 0021-9797 .- 1095-7103. ; 484, s. 279-290
-
Tidskriftsartikel (refereegranskat)abstract
- Adsorption of thiols with cationic or anionic terminal group on gold has been studied from mixed solutions of 11-Amino-1-undecanethiol (AUT) and 3-Mercaptopropionic acid (MPA) using Quartz Crystal Microbalance with Dissipation (QCM-D), X-ray Photoelectron Spectroscopy (XPS), atomic force microscopy (AFM) and contact angles. The goal is to probe the nature of such layers, and the additivity or otherwise of the pH responsiveness, with a view to evaluate their suitability as smart materials. For each of the two pure (unmixed) cases, ordered molecular monolayers are formed with sulfur binding to gold and the alkane chain pointing out from the surface as expected. Adsorption from the thiol mixtures, however, leads to a more complex behaviour. The surface concentration of thiols from the mixtures, as determined by QCM-D, is considerably lower than for the pure cases and it reaches a minimum at a 3:1 MPA/AUT relative concentration in the solution. The XPS results confirm a reduction in adsorbed amount in mixtures with the lowest overall intensity for the 3:1 ratio. Monolayers formed from mixtures display a wettability which is much lower and less pH sensitive. Collectively these results confirm that for adsorption from mixed systems, the configuration is completely different. Complex formation in the mixed solutions leads to the adsorption of molecules parallel to the surface in an axially in-plane configuration. This parallel layer of thiols is mechanically relatively robust to nano-shaving based on AFM measurements. These results will have a significant impact on the design of biomimetic surface coatings particularly when mixtures of oppositely charged molecules are present on the surface, as is commonly the case in biological, proteinaceous surfaces (e.g. hair and skin).
|
|
| 7. |
|
|
| 8. |
- Besharat, Zahra, et al.
(författare)
-
Se-C Cleavage of Hexane Selenol at Steps on Au(111)
- 2018
-
Ingår i: Langmuir. - : American Chemical Society (ACS). - 0743-7463 .- 1520-5827. ; 34:8, s. 2630-2636
-
Tidskriftsartikel (refereegranskat)abstract
- Selenols are considered as an alternative to thiols in self-assembled monolayers, but the Se-C bond is one limiting factor for their usefulness. In this study, we address the stability of the Se-C bond by a combined experimental and theoretical investigation of gas phase-deposited hexane selenol (CH3(CH2)(5)SeH) on Au(111) using photoelectron spectroscopy, scanning tunneling microscopy, and density functional theory (DFT). Experimentally, we find that initial adsorption leaves atomic Se on the surface without any carbon left on the surface, whereas further adsorption generates a saturated selenolate layer. The Se 3d component from atomic Se appears at 0.85 eV lower binding energy than the selenolate-related component. DFT calculations show that the most stable structure of selenols on Au(111) is in the form of RSe-Au-SeR complexes adsorbed on the unreconstructed Au(111) surface. This is similar to thiols on Au(111). Calculated Se 3d core-level shifts between elemental Se and selenolate in this structure nicely reproduce the experimentally recorded shifts. Dissociation of RSeH and subsequent formation of RH are found to proceed with high barriers on defect-free Au(111) terraces, with the highest barrier for scissoring R-Se. However, at steps, these barriers are considerably lower, allowing for Se-C bond breaking and hexane desorption, leaving elemental Se at the surface. Hexane is the selenol to selenolate formed by replacing the Se-C bond with a H-C bond by using the hydrogen liberated from transformation.
|
|
| 9. |
- Kanerva, M., et al.
(författare)
-
Automatization and stress analysis data of CoCr laser weld fatigue tests
- 2019
-
Ingår i: Data in Brief. - : Elsevier. - 2352-3409. ; 26
-
Tidskriftsartikel (refereegranskat)abstract
- This work includes raw and analyzed test data when using a recently developed fatigue test method for miniature laser welds in cobalt-chromium (CoCr) alloy joints [1]: 10.1016/j.jmbbm.2019.07.004. The automization of fatigue tests is crucial for saving costs and personnel resources and that is the reason why the atomization threshold and the resulting spectrum data related to CoCr welds are provided here. The finite element method based stress computation output is provided related to shearing-mode tests to support the dataset as a whole. In addition, the compositional data of the parent material and the laser weld are given.
|
|
| 10. |
- Kanerva, M., et al.
(författare)
-
Miniature CoCr laser welds under cyclic shear : Fatigue evolution and crack growth
- 2019
-
Ingår i: Journal of The Mechanical Behavior of Biomedical Materials. - : ELSEVIER. - 1751-6161 .- 1878-0180. ; 99, s. 93-103
-
Tidskriftsartikel (refereegranskat)abstract
- Miniature laser welds with the root depth in the range of 50-300 pm represent air-tight joints between the components in medical devices, such as those in implants, growth rods, stents and various prostheses. The current work focuses on the development of a fatigue test specimen and procedure to determine fatigue lives of shear-loaded laser welds. A cobalt-chromium (CoCr) alloy is used as a benchmark case. S-N graphs, damage process, and fracture surfaces are studied by applying x-ray analysis, atomic force microscopy, and scanning electron microscopy both before and after the crack onset. A non-linear material model is fitted for the CoCr alloy to run finite element simulations of the damage and deformation. As a result, two tensile-loaded specimen designs are established and the performance is compared to that of a traditional torque-loaded specimen. The new generation specimens show less variation in the determined fatigue lives due to well-defined crack onset point and, therefore, precise weld seam load during the experiments. The fatigue damage concentrates to the welded material and the entire weld experiences fatigue prior to the final, fracture-governed failure phase. For the studied weld seams of hardened CoCr, a regression fatigue limit of 10.8-11.8 MPa, where the stress refers to the arithmetic average shear stress computed along the region dominated by shear loading, is determined.
|
|
