| 1. |
- Hagleitner, Daniel R., et al.
(författare)
-
Bulk and surface characterization of In2O3(001) single crystals
- 2012
-
Ingår i: Physical Review B (Condensed Matter and Materials Physics). - 1098-0121. ; 85:11
-
Tidskriftsartikel (refereegranskat)abstract
- A comprehensive bulk and surface investigation of high-quality In2O3(001) single crystals is reported. The transparent-yellow, cube-shaped single crystals were grown using the flux method. Inductively coupled plasma mass spectrometry (ICP-MS) reveals small residues of Pb, Mg, and Pt in the crystals. Four-point-probe measurements show a resistivity of 2.0 +/- 0.5 x 10(5) Omega cm, which translates into a carrier concentration of approximate to 10(12) cm(-3). The results from x-ray diffraction (XRD) measurements revise the lattice constant to 10.1150(5) angstrom from the previously accepted value of 10.117 angstrom. Scanning tunneling microscopy (STM) images of a reduced (sputtered/annealed) and oxidized (exposure to atomic oxygen at 300 degrees C) surface show a step height of 5 angstrom, which indicates a preference for one type of surface termination. The surfaces stay flat without any evidence for macroscopic faceting under any of these preparation conditions. A combination of low-energy ion scattering (LEIS) and atomically resolved STM indicates an indium-terminated surface with small islands of 2.5 angstrom height under reducing conditions, with a surface structure corresponding to a strongly distorted indium lattice. Scanning tunneling spectroscopy (STS) reveals a pronounced surface state at the Fermi level (E-F). Photoelectron spectroscopy (PES) shows additional, deep-lying band gap states, which can be removed by exposure of the surface to atomic oxygen. Oxidation also results in a shoulder at the O 1s core level at a higher binding energy, possibly indicative of a surface peroxide species. A downward band bending of 0.4 eV is observed for the reduced surface, while the band bending of the oxidized surface is of the order of 0.1 eV or less.
|
|
| 2. |
- Wagner, Margareta, et al.
(författare)
-
Resolving the Structure of a Well-Ordered Hydroxyl Overlayer on In2O3(111) : Nanomanipulation and Theory
- 2017
-
Ingår i: ACS Nano. - : American Chemical Society (ACS). - 1936-0851 .- 1936-086X. ; 11:11, s. 11531-11541
-
Tidskriftsartikel (refereegranskat)abstract
- Changes in chemical and physical properties resulting from water adsorption play an important role in the characterization and performance of device-relevant materials. Studies of model oxides with well-characterized surfaces can provide detailed information that is vital for a general understanding of water-oxide interactions. In this work, we study single crystals of indium oxide, the prototypical transparent contact material that is heavily used in a wide range of applications and most prominently in optoelectronic technologies. Water adsorbs dissociatively already at temperatures as low as 100 K, as confirmed by scanning tunneling microscopy (STM), photoelectron spectroscopy, and density functional theory. This dissociation takes place on lattice sites of the defect-free surface. While the In2O3(111)-(1 × 1) surface offers four types of surface oxygen atoms (12 atoms per unit cell in total), water dissociation happens exclusively at one of them together with a neighboring pair of 5-fold coordinated In atoms. These O-In groups are symmetrically arranged around the 6-fold coordinated In atoms at the surface. At room temperature, the In2O3(111) surface thus saturates at three dissociated water molecules per unit cell, leading to a well-ordered hydroxylated surface with (1 × 1) symmetry, where the three water OWH groups plus the surface OSH groups are imaged together as one bright triangle in STM. Manipulations with the STM tip by means of voltage pulses preferentially remove the H atom of one surface OSH group per triangle. The change in contrast due to strong local band bending provides insights into the internal structure of these bright triangles. The experimental results are further confirmed by quantitative simulations of the STM image corrugation.
|
|
| 3. |
- Wagner, Margareta, et al.
(författare)
-
Well-ordered in adatoms at the In2 O3 (111) surface created by Fe deposition
- 2016
-
Ingår i: Physical Review Letters. - 0031-9007. ; 117:20
-
Tidskriftsartikel (refereegranskat)abstract
- Metal deposition on oxide surfaces usually results in adatoms, clusters, or islands of the deposited material, where defects in the surface often act as nucleation centers. Here an alternate configuration is reported. After the vapor deposition of Fe on the In2O3(111) surface at room temperature, ordered adatoms are observed with scanning tunneling microscopy. These are identical to the In adatoms that form when the sample is reduced by heating in ultrahigh vacuum. Density functional theory calculations confirm that Fe interchanges with In in the topmost layer, pushing the excess In atoms to the surface where they arrange as a well-ordered adatom array.
|
|
