| 1. |
- Li, N., et al.
(författare)
-
Tailoring Ordered Mesoporous Titania Films via Introducing Germanium Nanocrystals for Enhanced Electron Transfer Photoanodes for Photovoltaic Applications
- 2021
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-301X .- 1616-3028. ; 31:34
-
Tidskriftsartikel (refereegranskat)abstract
- Based on a diblock-copolymer templated sol–gel synthesis, germanium nanocrystals (GeNCs) are introduced to tailor mesoporous titania (TiO2) films for obtaining more efficient anodes for photovoltaic applications. After thermal annealing in air, the hybrid films with different GeNC content are investigated and compared with films undergoing an argon atmosphere annealing. The surface and inner morphologies of the TiO2/GeOx nanocomposite films are probed via scanning electron microscopy and grazing-incidence small-angle X-ray scattering. The crystal phase, chemical composition, and optical properties of the nanocomposite films are examined with transmission electron microscopy, X-ray photoelectron spectroscopy, and ultraviolet–visible spectroscopy. Special focus is set on the air-annealed nanocomposite films since they hold greater promise for photovoltaics. Specifically, the charge–carrier dynamics of these air-annealed nanocomposite films are studied, and it is found that, compared with pristine TiO2 photoanodes, the GeNC addition enhances the electron transfer, yielding an increase in the short-circuit photocurrent density of exemplary perovskite solar cells and thus, an enhanced device efficiency as well as a significantly reduced hysteresis.
|
|
| 2. |
- Brett, Calvin J., et al.
(författare)
-
Revealing structural evolution occurring from photo-initiated polymer network formation
- 2020
-
Ingår i: Communications Chemistry. - : Springer Science and Business Media LLC. - 2399-3669. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Photopolymerization is a key enabling technology offering spatial and temporal control to allow for future functional materials to be made to meet societal needs. However, gaining access to robust experimental techniques to describe the evolution of nanoscale morphology in photo-initiated polymeric systems has proven so far to be a challenging task. Here, we show that these physical transformations can be monitored and quantified at the nanoscale in situ and in real-time. It is demonstrated that the initial structural features of the liquid precursors significantly affect the final morphology and the physical properties of the resulting solid via the occurrence of local heterogeneities in the molecular mobility during the curing transformation. We have made visible how local physical arrestings in the liquid, associated with both cross-linking and vitrification, determine the length scale of the local heterogeneities forming upon curing, found to be in the 10-200nm range. Acomplete account of the structural evolution occurring during photopolymerisation is lacking. Here the physical changes occurring on the nanometer scale during photopolymerisation of acrylates are followed over time by FTIR, X-ray reflectometry, AFM, and GISAXS, offering insight into the mechanism by which initial composition influences the final morphology.
|
|
| 3. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 4. |
- Cao, Wei, et al.
(författare)
-
Spray-Deposited Anisotropic Ferromagnetic Hybrid Polymer Films of PS-b-PMMA and Strontium Hexaferrite Magnetic Nanoplatelets
- 2021
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 13:1, s. 1592-1602
-
Tidskriftsartikel (refereegranskat)abstract
- Spray deposition is a scalable and cost-effective technique for the fabrication of magnetic hybrid films containing diblock copolymers (DBCs) and magnetic nanoparticles. However, it is challenging to obtain spray-deposited anisotropic magnetic hybrid films without using external magnetic fields. In the present work, spray deposition is applied to prepare perpendicular anisotropic magnetic hybrid films by controlling the orientation of strontium hexaferrite nanoplatelets inside ultra-high-molecular-weight DBC polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) films. During spray deposition, the evolution of DBC morphology and the orientation of magnetic nanoplatelets are monitored with in situ grazing-incidence small-angle X-ray scattering (GISAXS). For reference, a pure DBC film without nanoplatelets is deposited with the same conditions. Solvent-controlled magnetic properties of the hybrid film are proven with solvent vapor annealing (SVA) applied to the final deposited magnetic films. Obvious changes in the DBC morphology and nanoplatelet localization are observed during SVA. The superconducting quantum interference device data show that ferromagnetic hybrid polymer films with high coercivity can be achieved via spray deposition. The hybrid films show a perpendicular magnetic anisotropy before SVA, which is strongly weakened after SVA. The spray-deposited hybrid films appear highly promising for potential applications in magnetic data storage and sensors.
|
|
| 5. |
- Chen, Q., et al.
(författare)
-
Biopolymer-Templated Deposition of Ordered and Polymorph Titanium Dioxide Thin Films for Improved Surface-Enhanced Raman Scattering Sensitivity
- 2022
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-301X .- 1616-3028. ; 32:6
-
Tidskriftsartikel (refereegranskat)abstract
- Titanium dioxide (TiO2) is an excellent candidate material for semiconductor metal oxide-based substrates for surface-enhanced Raman scattering (SERS). Biotemplated fabrication of TiO2 thin films with a 3D network is a promising route for effectively transferring the morphology and ordering of the template into the TiO2 layer. The control over the crystallinity of TiO2 remains a challenge due to the low thermal stability of biopolymers. Here is reported a novel strategy of the cellulose nanofibril (CNF)-directed assembly of TiO2/CNF thin films with tailored morphology and crystallinity as SERS substrates. Polymorphous TiO2/CNF thin films with well-defined morphology are obtained by combining atomic layer deposition and thermal annealing. A high enhancement factor of 1.79 × 106 in terms of semiconductor metal oxide nanomaterial (SMON)-based SERS substrates is obtained from the annealed TiO2/CNF thin films with a TiO2 layer thickness of 10 nm fabricated on indium tin oxide (ITO), when probed by 4-mercaptobenzoic acid molecules. Common SERS probes down to 10 nm can be detected on these TiO2/CNF substrates, indicating superior sensitivity of TiO2/CNF thin films among SMON SERS substrates. This improvement in SERS sensitivity is realized through a cooperative modulation of the template morphology of the CNF network and the crystalline state of TiO2.
|
|
| 6. |
- Chumakov, A., et al.
(författare)
-
Sprayed Nanometer-Thick Hard-Magnetic Coatings with Strong Perpendicular Anisotropy for Data Storage Applications
- 2022
-
Ingår i: ACS Applied Nano Materials. - : American Chemical Society (ACS). - 2574-0970. ; 5:7, s. 8741-8754
-
Tidskriftsartikel (refereegranskat)abstract
- The rapid growth of digital information in the world necessitates a big leap in improving the existing technologies for magnetic recording. For the best modern perpendicular recording, the highest coercivity materials with minimal volume are required. We present a study of a facile technology for establishing mono- and multilayer surfaces from various single-domain flat magnetic nanoparticles that exhibit a strong perpendicular-oriented magnetic moment on solid and flexible substrates. Surfactant-free, hard ferromagnetic, and single-domain anisotropic strontium hexaferrite SrFe12O19nanoparticles with a perpendicular magnetic moment orientation and two different aspect ratios are self-ordered into magnetic thin nanofilms, exploiting the templating effect of cellulose nanofibrils and magnetic fields. Uniform magnetic coatings obtained by the scalable layer-by-layer spray deposition from a monolayer coverage up to thicknesses of a few tens of nanometers show a preferred in-plane orientation of the hard-magnetic nanoparticles. High coercivities of the films of up to 5 kOe and a high perpendicular anisotropy of Mr⊥/Ms> 80% are found. The application of the magnetic field during film deposition ensures additional improvement in perpendicular magnetic anisotropy and the appearance of residual magnetization in the film of up to 0.6Ms. For low-aspect-ratio nanoparticles stacked in periodic planar structures, the signs of the photonic band gap are revealed. The ability to create scalable, thin magnetic structures based on nanosized particles/building blocks opens great opportunities for their application in a wide variety of optoelectronic and magnetic storage devices.
|
|
| 7. |
- Gensch, Marc, et al.
(författare)
-
Correlating Optical Reflectance with the Topology of Aluminum Nanocluster Layers Growing on Partially Conjugated Diblock Copolymer Templates
- 2021
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 13:47, s. 56663-56673
-
Tidskriftsartikel (refereegranskat)abstract
- Large-scale fabrication of metal cluster layers for usage in sensor applications and photovoltaics is a huge challenge. Physical vapor deposition offers large-scale fabrication of metal cluster layers on templates and polymer surfaces. In the case of aluminum (Al), only little is known about the formation and interaction of Al clusters during sputter deposition. Complex polymer surface morphologies can tailor the deposited Al cluster layer. Here, a poly(methyl methacrylate)-block-poly(3-hexylthiophen-2,5-diyl) (PMMA-b-P3HT) diblock copolymer template is used to investigate the nanostructure formation of Al cluster layers on the different polymer domains and to compare it with the respective homopolymers PMMA and P3HT. The optical properties relevant for sensor applications are monitored with ultraviolet-visible (UV-vis) measurements during the sputter deposition. The formation of Al clusters is followed in situ with grazing-incidence small-angle X-ray scattering (GISAXS), and the chemical interaction is revealed by X-ray photoelectron spectroscopy (XPS). Furthermore, atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM) yield topographical information about selective wetting of Al on the P3HT domains and embedding in the PMMA domains in the early stages, followed by four distinct growth stages describing the Al nanostructure formation.
|
|
| 8. |
- Gensch, Marc, et al.
(författare)
-
Selective Silver Nanocluster Metallization on Conjugated Diblock Copolymer Templates for Sensing and Photovoltaic Applications
- 2021
-
Ingår i: ACS Applied Nano Materials. - : American Chemical Society (ACS). - 2574-0970. ; 4:4, s. 4245-4255
-
Tidskriftsartikel (refereegranskat)abstract
- Polymer-metal composite films with nanostructured metal and/or polymer interfaces show a significant perspective for optoelectronic applications, for example, as sensors or in organic photovoltaics (OPVs). The polymer components used in these devices are mostly nanostructured conductive polymers with conjugated pi-electron systems. Enhanced OPV's power conversion efficiencies or sensor sensitivity can be achieved by selective metal deposition on or into polymer templates. In this study, we exploit time-resolved grazing-incidence X-ray scattering to observe the metal-polymer interface formation and the cluster crystallite size in situ during silver (Ag) sputter deposition on a poly(3-hexylthiophene-2,5-diyl)-b-poly(methyl methacrylate) (PMMA-b-P3HT) template. We compare the arising nanoscale morphologies with electronic properties, determine Ag growth regimes, and quantify the selective Ag growth for the diblock copolymer (DBC) template using the corresponding homopolymer thin films (P3HT and PMMA) as a reference. Hence, we are able to describe the influence of the respective polymer blocks and substrate effects on the Ag cluster percolation: the percolation threshold is correlated with the insulator-to-metal transition measured in situ with resistance measurements during the sputter deposition. The Ag cluster percolation on PMMA-b-P3HT starts already on the network of the hexagonal P3HT domain before a complete metal film covers the polymer surface, which is complemented by microscopic measurements. In general, this study demonstrates a possible method for the selective Ag growth as a scaffold for electrode preparation in nanoelectronics and for energy harvesting applications.
|
|
| 9. |
- Heger, J. E., et al.
(författare)
-
Low-Temperature and Water-Based Biotemplating of Nanostructured Foam-Like Titania Films Using ß-Lactoglobulin
- 2022
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-301X .- 1616-3028. ; 32:20
-
Tidskriftsartikel (refereegranskat)abstract
- Given the broad use of nanostructured crystalline titania films, an environmentally friendly and more sustainable synthesis route is highly desirable. Here, a water-based, low-temperature route is presented to synthesize nanostructured foam-like crystalline titania films. A pearl necklace-like nanostructure is introduced as tailored titania morphology via biotemplating with the use of the major bovine whey protein ß-lactoglobulin (ß-lg). It is shown that titania crystallization in a brookite-anatase mixed phase is promoted via spray deposition at a comparatively low temperature of 120 °C. The obtained crystallites have an average grain size of (4.2 ± 0.3) nm. In situ grazing incidence small-angle and wide-angle X-ray scattering (GISAXS/GIWAXS) are simultaneously performed to understand the kinetics of film formation and the templating role of ß-lg during spray coating. In the ß-lg:titania biohybrid composites, the crystal growth in semicrystalline titania clusters is sterically directed by the condensing ß-lg biomatrix. Due to using spray coating, the green chemistry approach to titania-based functional films can be scaled up on a large scale, which can potentially be used in photocatalytic processes or systems related to energy application.
|
|
| 10. |
- Ohm, Wiebke, et al.
(författare)
-
Morphological properties of airbrush spray-deposited enzymatic cellulose thin films
- 2018
-
Ingår i: JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH. - : Springer. - 1945-9645 .- 1547-0091 .- 1935-3804. ; 15:4, s. 759-769
-
Tidskriftsartikel (refereegranskat)abstract
- We investigate the layer formation of enzymatic cellulose by airbrush spray coating on silicon oxide surfaces. The layer structure and morphology of enzymatic cellulose films in the thickness range between 86 nm and 2.1 A mu m is determined as a function of the spray coating procedures. For each spray coating step, layer buildup, surface topography, crystallinity as well as the nanoscale structure are probed with atomic force microscopy and surface-sensitive X-ray scattering methods. Without intermittent drying, the film thickness saturates; with intermittent drying, a linear increase in layer thickness with the number of spray pulses is observed. A closed cellulose layer was always observed. The crystallinity remains unchanged; the nanoscale structures show three distinct sizes. Our results indicate that the smallest building blocks increasingly contribute to the morphology inside the cellulose network for thicker films, showing the importance of tailoring the cellulose nanofibrils. For a layer-by-layer coating, intermittent drying is mandatory.
|
|
