| 1. |
- Anselmo, Ana Sofia, 1980-, et al.
(författare)
-
Characterisation of vertical phase separation in polymer : fullerene blend films for photovoltaics by dSIMS and NEXAFS
- 2011
-
Ingår i: E-MRS 2011 Spring Meeting. - Malden, MA : John Wiley & Sons. ; , s. 62-63
-
Konferensbidrag (refereegranskat)abstract
- Morphological control and characterization of blend films is key in the development of viable polymer solar cells. Spontaneous formation of vertical compositional gradients during solution processing has been shown for polyfluorene:PCBM blends and rationalized with thermodynamic and kinetic models of nucleation and spinodal decomposition.[1, 2] The extent of vertical stratification is affected by polymer side-chain modification aimed at controlling polymer:fullerene miscibility.[3] Here we present high-resolution film morphology results for several polymer:fullerene systems as obtained from near-edge X-ray fine structure spectroscopy (NEXAFS) in partial and in total electron yield modes. Blend films were found to be polymer- enriched at the surface. Dynamic secondary ion mass spectrometry (dSIMS) and NEXAFS give compositional information at different depths, resulting in a more complete picture of the film morphology.
|
|
| 2. |
|
|
| 3. |
- Bjoerstroem, Cecilia M., et al.
(författare)
-
Influence of solvents and substrates on the morphology and the performance of low-bandgap polyfluorene: PCBM photovoltaic devices
- 2006
-
Ingår i: Proceedings of SPIE-The International Society for Optical Engineering. ; 6192, s. 61921X/1-
-
Konferensbidrag (refereegranskat)abstract
- Spin-coated thin films of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (APFO-3) blended with [6,6]-phenyl-C61-butyric acid Me ester (PCBM) are used as the active material in polymer photovoltaic cells. Such blends are known for their tendency to phase sep. during film formation. Tuning the morphol. of the blend in a controlled way is one possible road towards higher efficiency. We studied the effect of adding chlorobenzene to chloroform-based blend solns. before spin-coating on the conversion efficiency of APFO-3:PCBM photodiodes, and related that to the lateral and vertical morphol. of thin films of the blend. The lateral morphol. is imaged by at. force microscopy (AFM) and the vertical compositional profile is obtained by dynamic secondary ion mass spectrometry (SIMS). The profiles reveal compositional variations consisting of multilayers of alternating polymer-rich and PCBM-rich domains in the blend film spin-coated from chloroform. The vertical compositional variations are caused by surface-directed spinodal waves and are frozen in during the rapid evapn. of a highly volatile solvent. With addn. of the low-vapor pressure solvent chlorobenzene, a more homogeneous vertical compn. is found. The conversion efficiency for solar cells of this blend was found to be optimal for chloroform:chlorobenzene mixts. with a vol.-ratio of 80:1. We have also investigated the role of the substrate on the morphol. We found that blend films spin-coated from chloroform solns. on PEDOT:PSS-coated ITO show a similar compositional structure as the films on silicon, and that changing the substrate from silicon to gold only affects the vertical phase sepn. in a region close to the substrate interface. [on SciFinder (R)]
|
|
| 4. |
- Bjoerstroem, Cecilia M., et al.
(författare)
-
Multilayer formation in spin-coated thin films of low-bandgap polyfluorene: PCBM blends
- 2005
-
Ingår i: Journal of Physics: Condensed Matter. ; 17:50, s. L529-L534
-
Tidskriftsartikel (refereegranskat)abstract
- Blends of the low-bandgap polymer poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4',7'-di-2-thienyl- 2',1',3'-benzothiadiazole)] (APFO-3) and the fullerene deriv. [6,6]-phenyl-C61-butyric acid Me ester (PCBM) were spin-coated from chloroform soln. into thin films, which were examd. with dynamic secondary ion mass spectrometry. For blends with high PCBM content, the depth profiles show compn. waves that were caused by surface-directed phase sepn. during spin-coating. The formation of such multilayer structures by spontaneous self-stratification probably has implications for optimization strategies for the performance of org. solar cells. [on SciFinder (R)]
|
|
| 5. |
- Bjorstrom, Cecilia M., et al.
(författare)
-
Influence of solvents and substrates on the morphology and the performance of low-bandgap polyfluorene: PCBM photovoltaic devices - art. no. 61921X
- 2006
-
Ingår i: Proceedings of SPIE, the International Society for Optical Engineering. - : International Society for Optical Engineering; 1999. - 0277-786X .- 1996-756X. ; 6192, s. X1921-X1921
-
Tidskriftsartikel (refereegranskat)abstract
- Spin-coated thin films of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4,7-di-2-thienyl-2,1,3-benzothiadiazole)] (APFO-3) blended with [6,6]-phenyl-C-61-butyric acid methyl ester (PCBM) are used as the active material in polymer photovoltaic cells. Such blends are known for their tendency to phase separate during film formation. Tuning the morphology of the blend in a controlled way is one possible road towards higher efficiency. We studied the effect of adding chlorobenzene to chloroform-based blend solutions before spin-coating on the conversion efficiency of APFO-3:PCBM photodiodes, and related that to the lateral and vertical morphology of thin films of the blend. The lateral morphology is imaged by atomic force microscopy (AFM) and the vertical compositional profile is obtained by dynamic secondary ion mass spectrometry (SIMS). The profiles reveal compositional variations consisting of multilayers of alternating polymer-rich and PCBM-rich domains in the blend film spin-coated from chloroform. The vertical compositional variations are caused by surface-directed spinodal waves and are frozen in during the rapid evaporation of a highly volatile solvent. With addition of the low-vapour pressure solvent chlorobenzene, a more homogeneous vertical composition is found. The conversion efficiency for solar cells of this blend was found to be optimal for chloroform: chlorobenzene mixtures with a volume-ratio of 80:1. We have also investigated the role of the substrate on the morphology. We found that blend films spin-coated from chloroform solutions on PEDOT:PSS-coated ITO show a similar compositional structure as the films on silicon, and that changing the substrate from silicon to gold only affects the vertical phase separation in a region close to the substrate interface.
|
|
| 6. |
- Bjorstrom, C. M., et al.
(författare)
-
Vertical phase separation in spin-coated films of a low bandgap polyfluorene/PCBM blend - Effects of specific substrate interaction
- 2007
-
Ingår i: Applied Surface Science. - Amsterdam : Elsevier BV. - 0169-4332 .- 1873-5584. ; 253:8, s. 3906-3912
-
Tidskriftsartikel (refereegranskat)abstract
- We report on the effect of the substrate on the vertical phase separation in spin-coated thin films of poly [(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-4',7'-di-2-thienyl-2',1',3'-benz othiadiazole] (APFO-3) blended with [6,6]-phenyl-C-61-butyric acid methyl ester (PCBM). Compositional depth profiles of the films are measured by dynamic secondary ion mass spectrometry (SIMS). We found that changing the substrate from silicon to gold affects the composition profile near the substrate interface. This is caused by a specific interaction between the polymer (APFO-3) and the gold surface, as confirmed by X-ray photoelectron spectroscopy (XPS). The composition profile in the area away from the substrate interface, as well as the enrichment of the free surface with APFO-3, remain however unaffected by the choice of substrate. The vertical composition was also analysed for APFO-3:PCBM films spin-coated on indium tin oxide (ITO) coated with a thin layer of (3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS). (c) 2006 Elsevier B.V. All rights reserved.
|
|
| 7. |
|
|
| 8. |
- Björström, Cecilia M., et al.
(författare)
-
Influence of solvents and substrates on the morphology and the performance of low-bandgap polyfluorene:PCBM photovoltaic devices
- 2006
-
Ingår i: Proceedings of SPIE, the International Society for Optical Engineering. - Cardiff : SPIE - International Society for Optical Engineering. - 0277-786X .- 1996-756X. ; 6192, s. 61921X-
-
Tidskriftsartikel (refereegranskat)abstract
- Spin-coated thin films of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (APFO-3) blended with [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) are used as the active material in polymer photovoltaic cells. Such blends are known for their tendency to phase separate during film formation. Tuning the morphology of the blend in a controlled way is one possible road towards higher efficiency. We studied the effect of adding chlorobenzene to chloroform-based blend solutions before spin-coating on the conversion efficiency of APFO-3:PCBM photodiodes, and related that to the lateral and vertical morphology of thin films of the blend. The lateral morphology is imaged by atomic force microscopy (AFM) and the vertical compositional profile is obtained by dynamic secondary ion mass spectrometry (SIMS). The profiles reveal compositional variations consisting of multilayers of alternating polymer-rich and PCBM-rich domains in the blend film spin-coated from chloroform. The vertical compositional variations are caused by surface-directed spinodal waves and are frozen in during the rapid evaporation of a highly volatile solvent. With addition of the low-vapour pressure solvent chlorobenzene, a more homogeneous vertical composition is found. The conversion efficiency for solar cells of this blend was found to be optimal for chloroform:chlorobenzene mixtures with a volume-ratio of 80:1. We have also investigated the role of the substrate on the morphology. We found that blend films spin-coated from chloroform solutions on PEDOT:PSS-coated ITO show a similar compositional structure as the films on silicon, and that changing the substrate from silicon to gold only affects the vertical phase separation in a region close to the substrate interface
|
|
| 9. |
- Björström, Cecilia M., et al.
(författare)
-
Multilayer formation in spin-coated thin films of low-bandgap polyfluorene:PCBM blends
- 2005
-
Ingår i: Journal of Physics. - Philadelphia : Institute of Physics Publishing (IOPP). - 0953-8984 .- 1361-648X. ; 17:50, s. L529-L534
-
Tidskriftsartikel (refereegranskat)abstract
- Blends of the low-bandgap polymer poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5- (4',7'-di-2-thienyl-2',1',3'-benzothiadiazole] (APFO-3) and the fullerene derivative [6,6]-phenyl–C61–butyric acid methyl ester (PCBM) were spin-coated from chloroform solution into thin films, which were examined with dynamic secondary ion mass spectrometry. For blends with high PCBM content, the depth profiles show composition waves that were caused by surface-directed phase separation during spin-coating. The formation of such multilayer structures by spontaneous self-stratification is likely to have implications for optimization strategies for the performance of organic solar cells
|
|
| 10. |
- Budkowski, Andrzej, et al.
(författare)
-
Polymer Blends Spin-Cast into Films with Complementary Elements for Electronics and Biotechnology
- 2012
-
Ingår i: Journal of Applied Polymer Science. - Malden, MA : John Wiley & Sons. - 0021-8995 .- 1097-4628. ; 125:6, s. 4275-4284
-
Tidskriftsartikel (refereegranskat)abstract
- Versatility of solution-processing strategy based on the simultaneous rather than additive deposition of different functional molecules is discussed. It is shown that spin-cast polymer blends result in films with domains that could form elements with complementary functions of (i) solar cells, (ii) electronic circuitries, and (iii) test plates for protein micro-arrays: Alternating layers, rich in electrondonating polyfluorene and electron-accepting fullerene derivative, result in optimized solar power conversion. Surface patterns, made by soft lithography, align conductive paths of conjugated poly(3-alkylthiophene) in dielectric polystyrene. Proteins, preserving their biologically activity, are adsorbed to hydrophobic domains of polystyrene in hydrophilic matrix of poly(ethylene oxide). The authors report the research progress on structure formation in three polymer blend families, resulting in films with complementary elements for electronics and biotechnology. Blend film structures are determined with secondary ion mass spectrometry, atomic force microscopy, and fluorescence microscopy. In addition, the authors present recent results on (i) structure formation in fullerene derivative/poly(3-alkylthiophene) blends intended for solar cells, (ii) 3-dimensional SIMS imaging of conductive paths of poly(3-alkylthiophene) in dielectric polystyrene, (iii) test lates for multiprotein micro-arrays fabricated with blend films of hydrophobic polystyrene and thermoresponsive poly (N-sopropylacrylamide).
|
|
