| 1. |
-
Overview of the JET results
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:10
-
Tidskriftsartikel (refereegranskat)
|
|
| 2. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 3. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 4. |
- Pucella, G., et al.
(författare)
-
Overview of the FTU results
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 62:4
-
Forskningsöversikt (refereegranskat)abstract
- Since the 2018 IAEA FEC Conference, FTU operations have been devoted to several experiments covering a large range of topics, from the investigation of the behaviour of a liquid tin limiter to the runaway electrons mitigation and control and to the stabilization of tearing modes by electron cyclotron heating and by pellet injection. Other experiments have involved the spectroscopy of heavy metal ions, the electron density peaking in helium doped plasmas, the electron cyclotron assisted start-up and the electron temperature measurements in high temperature plasmas. The effectiveness of the laser induced breakdown spectroscopy system has been demonstrated and the new capabilities of the runaway electron imaging spectrometry system for in-flight runaways studies have been explored. Finally, a high resolution saddle coil array for MHD analysis and UV and SXR diamond detectors have been successfully tested on different plasma scenarios.
|
|
| 5. |
- Cruz, N., et al.
(författare)
-
Real-time software tools for the performance analysis of the ITER Radial Neutron Camera
- 2017
-
Ingår i: Fusion engineering and design. - : ELSEVIER SCIENCE SA. - 0920-3796 .- 1873-7196. ; 123, s. 1001-1005
-
Tidskriftsartikel (refereegranskat)abstract
- The Radial Neutron Camera (RNC) diagnostic is a neutron detection system with multiple collimators aiming at characterizing the neutron emission that will be produced by the ITER tokamak. The RNC plays a primary role for basic and advanced plasma control measurements and acts as backup for system machine protection measurements. During the RNC system level design phase the following real-time data processing algorithms were developed to assess RNC data throughput needs and measurement performances: (i) real-time data compression block (ii) real-time calculation of the neutron emissivity radial profile, based on Tikhonov regularization, starting from the line-integrated measurements, the line-of-sight geometry and using the magnetic flux information [1] (iii) real-time calculation of the neutron emissivity profile using a priori trained neural networks, the line-integrated measurements and the magnetic flux information (the best output from different neural networks being evaluated by a figure of merit that maps the neutron emissivity profile to the original line-integrated measurements) [21]. This paper presents results for the processing times of the various algorithms and their minimum control cycle for different conditions, such as number of lines of sight, number of magnetic flux surfaces and measurement error on the line integrated RNC measurements.
|
|
| 6. |
- Esposito, B., et al.
(författare)
-
Progress of Design and Development for the ITER Radial Neutron Camera
- 2022
-
Ingår i: Journal of fusion energy. - : Springer. - 0164-0313 .- 1572-9591. ; 41:2
-
Tidskriftsartikel (refereegranskat)abstract
- The paper presents an overview of the design status of the Radial Neutron Camera (RNC), that, together with the Vertical Neutron Camera, will provide, through reconstruction techniques applied to the measured line-integrated neutron fluxes, the time resolved measurement of the ITER neutron and alpha-source profile (i.e. neutron emissivity, neutrons emitted per unit time and volume). The RNC is composed of two subsystems, the In-Port RNC and Ex-Port RNC located, respectively, inside and outside the Plug of Equatorial Port #01. The In-Port subsystem is in a more advanced design stage since it has recently undergone the Final Design Review in the ITER procurement process. The paper describes the diagnostic layout, the interfaces, the measurement capabilities and the main challenges in its realization. Prototyping and testing of neutron detectors and electronics components were carried out and led to the choice of the component solutions that can match the environmental and operational constraints in terms radiation hardness, high temperature and electromagnetic compatibility. The performance of the RNC in terms of neutron emissivity measurement capability was assessed through 1D and 2D reconstruction analysis. It is proven that the neutron emissivity can be reconstructed in real-time within the measurement requirements: 10% accuracy, 10 ms time resolution and a/10 (a = plasma minor radius) space resolution.
|
|
| 7. |
- Riva, M., et al.
(författare)
-
High-Priority Prototype Testing in Support of System-Level Design Development of the ITER Radial Neutron Camera
- 2018
-
Ingår i: IEEE Transactions on Plasma Science. - : IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC. - 0093-3813 .- 1939-9375. ; 46:5, s. 1291-1297
-
Tidskriftsartikel (refereegranskat)abstract
- This paper describes the high-priority testing activities supporting the ITER radial neutron camera (RNC) design, performed by a consortium of European institutes within a framework contract placed by fusion for energy, the ITER European Domestic Agency. The main role of the RNC is to measure the uncollided 14- and 2.5-MeV neutrons from deuterium-tritium and deuterium-deuterium fusion reactions through an array of flux monitors/spectrometers located in collimated lines of sight viewing the plasma through the ITER equatorial port plug #1. The line-integrated neutron fluxes will be used to evaluate, through reconstruction techniques, the radial profile of the neutrons emitted per unit time and volume (neutron emissivity) and, therefore, the neutron yield and the alpha particles' birth profile. The activity of high-priority testing is dedicated to the preparation and the design of experimental test environment, the conduction of appropriate tests and reporting of test results for the high-priority prototypes, clarifying or verifying the expected key function and system behavior, and enhancing learning on specific issues (potential showstoppers).
|
|
