| 1. |
|
|
| 2. |
- Abbas, Ghazanfar, et al.
(författare)
-
Electrochemical study of nanostructured electrode for low-temperature solid oxide fuel cell (LTSOFC)
- 2014
-
Ingår i: International Journal of Energy Research. - : Hindawi Limited. - 0363-907X .- 1099-114X. ; 38:4, s. 518-523
-
Tidskriftsartikel (refereegranskat)abstract
- Zn-based nanostructured Ba0.05Cu0.25Fe0.10Zn0.60O (BCFZ) oxide electrode material was synthesized by solid-state reaction for low-temperature solid oxide fuel cell. The cell was fabricated by sandwiching NK-CDC electrolyte between BCFZ electrodes by dry press technique, and its performance was assessed. The maximum power density of 741.87 mW-cm(-2) was achieved at 550 degrees C. The crystal structure and morphology were characterized by X-ray diffractometer (XRD) and SEM. The particle size was calculated to be 25 nm applying Scherer's formula from XRD data. Electronic conductivities were measured with the four-probe DC method under hydrogen and air atmosphere. AC Electrochemical Impedance Spectroscopy of the BCFZ oxide electrode was also measured in hydrogen atmosphere at 450 degrees C.
|
|
| 3. |
- Abbas, Ghazanfar, et al.
(författare)
-
Synthesize and characterization of nanocomposite anodes for low temperature solid oxide fuel cell
- 2015
-
Ingår i: International journal of hydrogen energy. - : Elsevier BV. - 0360-3199 .- 1879-3487. ; 40:1, s. 891-897
-
Tidskriftsartikel (refereegranskat)abstract
- Solid oxide fuel cells have much capability to become an economical alternative energy conversion technology having appropriate materials that can be operated at comparatively low temperature in the range of 400-600 degrees C. The nano-scale engineering has been incorporated to improve the catalytic activity of anode materials for solid oxide fuel cells. Nanostructured Al0.10NixZn0.90-xO oxides were prepared by solid state reaction, which were then mixed with the prepared Gadolinium doped Ceria GDC electrolyte. The crystal structure and surface morphology were characterized by XRD and SEM. The particle size was evaluated by XRD data and found in the range of 20-50 nm, which was then ensured by SEM pictures. The pellets of 13 mm diameter were pressed by dry press technique and electrical conductivities (DC and AC) were determined by four probe techniques and the values have been found to be 10.84 and 4.88 S/cm, respectively at hydrogen atmosphere in the temperature range of 300-600 degrees C. The Electrochemical Impedance Spectroscopy (EIS) analysis exhibits the pure electronic behavior at hydrogen atmosphere. The maximum power density of ANZ-GDC composite anode based solid oxide fuel cell has been achieved 705 mW/cm(2) at 550 degrees C.
|
|
| 4. |
- Abbas, Ghazanfar, et al.
(författare)
-
Preparation and Characterization of Nanocomposite Calcium Doped Ceria Electrolyte With Alkali Carbonates (NK-CDC) for SOFC
- 2011
-
Ingår i: Journal of Fuel Cell Science and Technology. - : ASME International. - 1550-624X .- 1551-6989. ; 8:4, s. 041013-
-
Tidskriftsartikel (refereegranskat)abstract
- The entire world's challenge is to find out the renewable energy sources due to rapid depletion of fossil fuels because of their high consumption. Solid oxide fuel cells (SOFCs) are believed to be the best alternative source, which converts chemical energy into electricity without combustion. Nanostructure study is required to develop highly ionic conductive electrolytes for SOFCs. In this work, the calcium doped ceria (Ce0.8Ca0.2O1.9) coated with 20% molar ratio of two alkali carbonates (CDC-M: MCO3, where M = Na and K) electrolyte was prepared by coprecipitation method. Ni based electrode was used to fabricate the cell by dry pressing technique. The crystal structure and surface morphology were characterized by an X-ray diffractometer, scanning electron microscopy (SEM), and high resolution transmission electron microscopy (TEM). The particle size was calculated in the range 10-20 nm by Scherer's formula and compared with SEM and TEM results. The ionic conductivity was measured by using ac electrochemical impedance spectroscopy method. The activation energy was also evaluated. The performance of the cell was measured 0.567 W/cm(2) at temperature 550 degrees C with hydrogen as a fuel.
|
|
| 5. |
- Abbas, Ghazanfar, et al.
(författare)
-
Study of CuNiZnGdCe-Nanocomposite Anode for Low Temperature SOFC
- 2012
-
Ingår i: Nanoscience and Nanotechnology Letters. - : American Scientific Publishers. - 1941-4900 .- 1941-4919. ; 4:4, s. 389-393
-
Tidskriftsartikel (refereegranskat)abstract
- Composite electrodes of Cu0.16Ni0.27Zn0.37Ce0.16Gd0.04 (CNZGC) oxides have been successfully synthesized by solid state reaction method as anode material for low temperature solid oxide fuel cell (LTSOFC). These electrodes are characterized by XRD followed by sintering at various time periods and temperatures. Particle size of optimized composition was calculated 40-85 nm and sintered at 800 degrees C for 4 hours. Electrical conductivity of 4.14 S/cm was obtained at a temperature of 550 degrees C by the 4-prob DC method. The activation energy was calculated 4 x 10(-2) eV at 550 degrees C. Hydrogen was used as fuel and air as oxidant at anode and cathode sides respectively. I-V/I-P curves were obtained in the temperature range of 400-550 degrees C. The maximum power density was achieved for 570 mW/cm(2) at 550 degrees C.
|
|
