| 1. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 2. |
- Chen, Jinhan, et al.
(författare)
-
The effect of hot isostatic pressing on thermal conductivity of additively manufactured pure tungsten
- 2020
-
Ingår i: International journal of refractory metals & hard materials. - : Elsevier BV. - 0263-4368. ; 87
-
Tidskriftsartikel (refereegranskat)abstract
- The crack-healing behaviors and microstructure evolution of pure tungsten produced by laser powder bed fusion (LPBF) were studied and compared before and after post hot isostatic pressing (post-HIP) treatment. An average thermal conductivity of 133 W.m(-1).K-1 at room temperature (RT) was obtained after HIP, which was 16% higher than that of as-built sample (115 W.m(-1).K-1). Although the HIP process had little effect on density, it resulted in a large grain size of > 300 mu m accompanied by a decrease in dislocation density and crack healing, which led to a substantial improvement of thermal conductivity of pure tungsten. The positive correlation between relative density and thermal conductivity of as-built tungsten was reported.
|
|
| 3. |
- Li, Kailun, et al.
(författare)
-
Crack suppression in additively manufactured tungsten by introducing secondary-phase nanoparticles into the matrix
- 2019
-
Ingår i: International journal of refractory metals & hard materials. - : Elsevier BV. - 0263-4368. ; 79, s. 158-163
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, an effective strategy was developed to suppress cracking by introducing secondary-phase ZrC nanoparticles into a tungsten (W) matrix. Pure W and W-0.5wt%ZrC bulks were additively manufactured via the laser powder bed fusion (LPBF) technique, and their cracking behaviour was compared. It was observed that the crack density of W-ZrC was reduced by 88.7% compared with that of pure W. The grains in W-ZrC were obviously refined compared with the grains in pure W, which significantly increased the cracking resistance. In addition, ZrC diminished the oxygen impurities, further increasing the cracking resistance. This study provides a promising strategy for the additive manufacturing of high-quality W by introducing secondary-phase nanoparticles into the metal matrix.
|
|
| 4. |
- Liu, Wei, et al.
(författare)
-
Household renovation before and during pregnancy in relation to preterm birth and low birthweight in China
- 2019
-
Ingår i: Indoor Air. - : WILEY. - 0905-6947 .- 1600-0668. ; 29:2, s. 202-214
-
Tidskriftsartikel (refereegranskat)abstract
- From October 2010 to April 2012, we conducted a cross-sectional study of associations between household environments and childhood health among preschool children in eight Chinese cities. Here, we analyze associations of early household renovation with preterm birth (PTB), low birthweight (LBW), term low birthweight (Term-LBW), and small for gestational age (SGA). Parents responded to questions about household renovation and their children's gestational age and birthweight. In the multivariate logistic regression analyses, household renovation in the year before pregnancy was significantly associated with LBW (sample size: N = 25 813; adjusted odds ratio (OR) with 95% confidence intervals (CIs): 1.23, 1.01-1.50) and Term-LBW (N = 24 823; 1.29, 1.01-1.67). Household renovation during pregnancy was significantly associated with PTB (N = 25 202; 1.28, 1.01-1.69). These significant associations were also found in the two-level (city-child) logistic regression analyses and in the sensitivity analyses among 21 009 children with complete data in all studied variates. Stronger associations were found in certain subgroups. Our findings indicate that household renovation within one year before pregnancy might be a risk factor for LBW and Term-LBW, while household renovation during pregnancy could be a risk factor for PTB.
|
|
| 5. |
- Wang, Yafei, et al.
(författare)
-
A Data-Driven Scheme for Quantitative Analysis of Texture
- 2020
-
Ingår i: Metallurgical and Materials Transactions. A. - : Springer Science and Business Media LLC. - 1073-5623 .- 1543-1940. ; 51:2, s. 940-950
-
Tidskriftsartikel (refereegranskat)abstract
- Texture is the orientation distribution of crystallites in polycrystalline materials. Given the discrete orientations, Schaeben suggested to adopt statistics for quantitative analysis of texture from discrete orientations, and he also conceived a clustering algorithm to facilitate the applications of statistical methods (H. Schaeben, J Appl Crystal 26:112-121, 1993). This data-driven scheme becomes more urgent and more necessary for the oncoming fourth paradigm: data-intensive scientific discovery, which follows after experimental science, theoretical science, and computational science paradigm. This research adopts a density-based clustering algorithm, DBSCAN, to process the orientation data from an austenitic stainless steel 316 L sample fabricated by selective laser melting. It is validated that the algorithm can robustly identify the orientation cluster (or texture component or preferred orientation). The statistical methods can successfully quantify the features of the identified orientation cluster with quantified uncertainty (statistical significance), which is often lacked in the general method of orientation distribution function. It is believed that this data-driven scheme can be applied to the many aspects of texture analysis.
|
|
| 6. |
- Wang, Yafei, et al.
(författare)
-
Construction of Cellular Substructure in Laser Powder Bed Fusion
- 2019
-
Ingår i: Metals. - : MDPI AG. - 2075-4701.
-
Tidskriftsartikel (refereegranskat)abstract
- Cellular substructure has been widely observed in the sample fabricated by laser powder bed fusion, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two-dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track of austenitic stainless steel 316L is distinguished between the cell-like dendrite and the cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. When the power is 200 W, the critical growth rate of the transition in the single track can be around 0.31 ms(-1).
|
|
| 7. |
- Wang, Yafei, et al.
(författare)
-
Grain structure and texture of the SLM single track
- 2020
-
Ingår i: Journal of Materials Processing Technology. - : Elsevier BV. - 0924-0136 .- 1873-4774. ; 281
-
Tidskriftsartikel (refereegranskat)abstract
- The grain structure and texture of metal parts fabricated by selective laser melting (SLM) are of interest for their effect on the properties. The study of the SLM single track can reduce the variables to be concerned and, hence, facilitate the understanding of the development of grain and texture in the SLM process. In this work, the austenitic stainless 316L single tracks are fabricated at different scanning speeds, and they are characterized by electron backscattered diffraction (EBSD) from transverse, serial transverse, and longitudinal cross-sections. It is validated that curved grain is common in the SLM single track. The effects of the varied thermal gradient and the shape of the melt pool on competitive growth of grain are analyzed. All the three equivalent < 001 > orientations of the columnar grain are considered, which leads us to put forward a crystallographic feature of a favorable grain during the competitive growth in SLM. Such a crystallographic feature is validated by the texture of the SLM single track, especially the < 001 > // scanning direction (SD) texture.
|
|
| 8. |
- Zhang, Yinping, et al.
(författare)
-
Ten cities cross-sectional questionnaire survey of children asthma and other allergies in China
- 2013
-
Ingår i: Chinese Science Bulletin. - : Springer Science and Business Media LLC. - 1001-6538 .- 1861-9541. ; 58:34, s. 4182-4189
-
Tidskriftsartikel (refereegranskat)abstract
- Asthma, rhinitis and eczema (allergic or non-allergic) have increased throughout the world during the last decades, especially among children. Changes in the indoor environment are suspected to be important causes. China has experienced a dramatic change in indoor environmental exposures during the past two decades. However, such changes and their associations with children's asthma and other health aspects have not been thoroughly studied. China, Children, Homes, Health (CCHH), Phase I, was a cross-sectional questionnaire survey of 48219 children 1-8 years old in 10 Chinese cities during 2010-2012. The questionnaire includes the International Study of Asthma and Allergies in Childhood (ISAAC) core health questions and additional questions regarding housing, life habits and outdoor environment. In health analyses, children aged 3-6 years old were included. The prevalences of doctor diagnosed asthma varied from 1.7% to 9.8% (mean 6.8%), a large increase from 0.91% in 1999 and 1.50% in 2000. The prevalence of wheeze, rhinitis and atopic eczema (last 12 months) varied from 13.9% to 23.7%, 24.0% to 50.8% and 4.8% to 15.8%, respectively. Taiyuan had the lowest prevalences of all illnesses and Shanghai the highest, except for wheezewhere the highest value was for Urumqi. We found (1) no obvious association between disease prevalences and ambient PM10 concentrations and (2) higher prevalences of disease in humid climates with hot summers and cold winters, but with no centrally heated buildings. Associations between the diseases and economic status as indexed by Gross Domestic Product (GDP) requires further study.
|
|
