| 1. |
- Alecrim, Viviane, et al.
(författare)
-
Exfoliated Layered Materials for Digital Fabrication
- 2015
-
Ingår i: NIP & Digital Fabrication Conference. ; , s. 192-194
-
Konferensbidrag (refereegranskat)abstract
- We introduced an exfoliation method of MoS2 in a 3% solution of sodium dodecyl surfactant at high concentration (i.e. 2 g/L). The bulk MoS2 was thinned by mechanical exfoliation between sand papers and the resulting powder was used to prepare dispersions by liquid exfoliation through probe sonication. The resulting dispersion consisted of very thin MoS2 nanosheets in surfactant solution with average lateral size around 126 nm. This may be interesting for applications in inkjet printed electronics.
|
|
| 2. |
|
|
| 3. |
- Alimohammadzadeh, Rana, et al.
(författare)
-
Scalable Improvement of the Strength Properties of Chemimechanical Pulp Fibers by Eco-Friendly Catalysis
- 2018
-
Ingår i: IMPC 2018. - Trondheim, Norway.
-
Konferensbidrag (refereegranskat)abstract
- The sustainable improvement of the strength properties of chemimechanical pulp by eco-friendlycatalysis is disclosed. Significant research activities have been performed on the use of cationic starchand polyelectrolyte complexes for improving the strength properties of cellulose-based materials. Herewe apply an eco-friendly strategy based on catalysis for significantly improving the strength propertiesof sheets made from chemimechanical pulp (CTMP) and bleeched sulphite pulp (BSP) using sustainablepolyelectrolyte complexes as the strength additives and organocatalysis. This surface engineeringstrategy significantly increased the strength properties of the assembled sheets (up to 100% in the caseof Z-strength). We also developed a catalytic selective colour marking of the cationic potato starch (CS)and carboxymethylcellulose (CMC) in order to elucidated how the specific strength additives aredistributed on the sheets. It revealed that the strength additives were more evenly distributed on thesheets made from CTMP as compared to BSP sheets. This is most likely attributed to the presence oflignin in the former lignocellulosic material. It also contributes to the increase in strength (up to 100%,Z-strength) for the CTMP derived sheets. The selective colour marking method also revealed that morestrength additives had been bound to the pulps in the presence of the catalyst.
|
|
| 4. |
- Alimohammadzadeh, Rana, et al.
(författare)
-
Sustainable Surface Engineering of Lignocellulose and Cellulose by Synergistic Combination of Metal‐Free Catalysis and Polyelectrolyte Complexes
- 2019
-
Ingår i: Global Challenges. - : Wiley. - 2056-6646. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- A sustainable strategy for synergistic surface engineering of lignocellulose and cellulose fibers derived from wood by synergistic combination of metal‐free catalysis and renewable polyelectrolyte (PE) complexes is disclosed. The strategy allows for improvement and introduction of important properties such as strength, water resistance, and fluorescence to the renewable fibers and cellulosic materials. For example, the “green” surface engineering significantly increases the strength properties (up to 100% in Z‐strength) of chemi‐thermomechanical pulp (CTMP) and bleached sulphite pulp (BSP)‐derived sheets. Next, performing an organocatalytic silylation with a nontoxic organic acid makes the corresponding lignocellulose and cellulose sheets hydrophobic. A selective color modification of polysaccharides is developed by combining metal‐free catalysis and thiol‐ene click chemistry. Next, fluorescent PE complexes based on cationic starch (CS) and carboxymethylcellulose (CMC) are prepared and used for modification of CTMP or BSP in the presence of a metal‐free catalyst. Laser‐scanning confocal microscopy reveals that the PE‐strength additive is evenly distributed on the CTMP and heterogeneously on the BSP. The fluorescent CS distribution on the CTMP follows the lignin distribution of the lignocellulosic fibers.
|
|
| 5. |
|
|
| 6. |
- Andres, Britta, 1986-, et al.
(författare)
-
Cellulose binders for electric double-layer capacitor electrodes : The influence of cellulose quality on electrical properties
- 2018
-
Ingår i: Materials & design. - : Elsevier BV. - 0264-1275 .- 1873-4197. ; 141, s. 342-349
-
Tidskriftsartikel (refereegranskat)abstract
- Cellulose derivatives are widely used as binders and dispersing agents in different applications. Binders composed of cellulose are an environmentally friendly alternative to oil-based polymer binding agents. Previously, we reported the use of cellulose nanofibers (CNFs) as binders in electrodes for electric double-layer capacitors (EDLCs). In addition to good mechanical stability, we demonstrated that CNFs enhanced the electrical performance of the electrodes. However, cellulose fibers can cover a broad range of length scales, and the quality requirements from an electrode perspective have not been thoroughly investigated. To evaluate the influence of fiber quality on electrode properties, we tested seven samples with different fiber dimensions that are based on the same kraft pulp. To capture the length scale from fibers to nanofibrils, we evaluated the performance of the untreated kraft pulp, refined fibers, microfibrillated cellulose (MFC) and CNFs. Electrodes with kraft pulp or refined fibers showed the lowest electrical resistivity. The specific capacitances of all EDLCs were surprisingly similar, but slightly lower for the EDLC with CNFs. The same electrode sample with CNFs also showed a slightly higher equivalent series resistance (ESR), compared to those of the other EDLCs. Graphite dispersions with MFC showed the best dispersion stability.
|
|
| 7. |
- Andres, Britta, 1986-, et al.
(författare)
-
Electrode Mass Balancing as an Inexpensive and Simple Method to Increase the Capacitance of Electric Double-Layer Capacitors
- 2016
-
Ingår i: PLOS ONE. - : Public Library of Science (PLoS). - 1932-6203. ; 11:9, s. 1-12
-
Tidskriftsartikel (refereegranskat)abstract
- Symmetric electric double-layer capacitors (EDLCs) have equal masses of the same active material in both electrodes. However, having equal electrode masses may prevent the EDLC to have the largest possible specific capacitance if the sizes of the hydrated anions and cations in the electrolyte differ because the electrodes and the electrolyte may not be completely utilized. Here we demonstrate how this issue can be resolved by mass balancing. If the electrode masses are adjusted according to the size of the ions, one can easily increase an EDLC's specific capacitance. To that end, we performed galvanostatic cycling to measure the capacitances of symmetric EDLCs with different electrode mass ratios using four aqueous electrolytes-Na2SO4, H2SO4, NaOH, and KOH (all with a concentration of 1 M)-and compared these to the theoretical optimal electrode mass ratio that we calculated using the sizes of the hydrated ions. Both the theoretical and experimental values revealed lower-than-1 optimal electrode ratios for all electrolytes except KOH. The largest increase in capacitance was obtained for EDLCs with NaOH as electrolyte. Specifically, we demonstrate an increase of the specific capacitance by 8.6% by adjusting the electrode mass ratio from 1 to 0.86. Our findings demonstrate that electrode mass balancing is a simple and inexpensive method to increase the capacitance of EDLCs. Furthermore, our results imply that one can reduce the amount of unused material in EDLCs and thus decrease their weight, volume and cost.
|
|
| 8. |
- Andres, Britta, et al.
(författare)
-
Enhanced electrical and mechanical properties of nanographite electrodes for supercapacitors by addition of nanofibrillated cellulose
- 2014
-
Ingår i: Physica status solidi. B, Basic research. - : Wiley. - 0370-1972 .- 1521-3951. ; 251:12, s. 2581-2586
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene and porous carbon materials are widely used as electrodes in supercapacitors. In order to form mechanically stable electrodes, binders can be added to the conducting electrode material. However, most bindersdegrade the electrical performance of the electrodes. Here we show that by using nanofibrillated cellulose(NFC) as binder the electrical properties, such as capacitance, were enhanced. The highest capacitance was measured at a NFC content of approximately 10% in ratio to the total amount of active material. NFC is a good ionconductor and improves the access of ions in the electrodes. Thus, electrodes made of a mixture of nanographite and NFC achieved larger capacitances in supercapacitors than electrodes with nanographite only. In addition to electrical properties, NFC enhanced the mechanical stability and wet strength of the electrodes significantly. Furthermore, NFC stabilized the aqueous nanographite dispersions, which improved the processability. Galvanostatic cycling was performed and an initial transient behaviour of the supercapacitors during the first cycles was observed. However, stabilized supercapacitors showed efficiencies of 98–100 %.
|
|
| 9. |
- Andres, Britta, 1986-
(författare)
-
Low-Cost, Environmentally Friendly Electric Double-Layer Capacitors : Concept, Materials and Production
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Today’s society is currently performing an exit from fossilfuel energy sources. The change to sustainable alternativesrequires inexpensive and environmentally friendly energy storagedevices. However, most current devices contain expensive,rare or toxic materials. These materials must be replaced bylow-cost, abundant, nontoxic components.In this thesis, I suggest the production of paper-based electricdouble-layer capacitors (EDLCs) to meet the demand oflow-cost energy storage devices that provide high power density.To fulfill the requirements of sustainable and environmentallyfriendly devices, production of EDLCs that consist of paper,graphite and saltwater is proposed. Paper can be used as aseparator between the electrodes and as a substrate for theelectrodes. Graphite is suited for use as an active material in theelectrodes, and saltwater can be employed as an electrolyte.Westudied and developed different methods for the productionof nanographite and graphene from graphite. Composites containingthese materials and similar advanced carbon materialshave been tested as electrode materials in EDLCs. I suggest theuse of cellulose nanofibers (CNFs) or microfibrillated cellulose(MFC) as a binder in the electrodes. In addition to improvedmechanical stability, the nanocellulose improved the stabilityof graphite dispersions and the electrical performance of theelectrodes. The influence of the cellulose quality on the electricalproperties of the electrodes and EDLCs was investigated.The results showed that the finest nanocellulose quality is notthe best choice for EDLC electrodes; MFC is recommended forthis application instead. The results also demonstrated thatthe capacitance of EDLCs can be increased if the electrodemasses are adjusted according to the size of the electrolyte ions.Moreover, we investigated the issue of high contact resistancesat the interface between porous carbon electrodes and metalcurrent collectors. To reduce the contact resistance, graphitefoil can be used as a current collector instead of metal foils.Using the suggested low-cost materials, production methodsand conceptual improvements, it is possible to reduce the material costs by more than 90% in comparison with commercialunits. This confirms that paper-based EDLCs are apromising alternative to conventional EDLCs. Our findings andadditional research can be expected to substantially supportthe design and commercialization of sustainable EDLCs andother green energy technologies.
|
|
| 10. |
- Blomquist, Nicklas, 1987-, et al.
(författare)
-
Effects of Geometry on Large-scale Tube-shear Exfoliation of Multilayer Graphene and Nanographite in Water
- 2019
-
Ingår i: Scientific Reports. - : Springer Science and Business Media LLC. - 2045-2322. ; 9:1
-
Tidskriftsartikel (refereegranskat)abstract
- Industrially scalable methods for the production of graphene and other nanographites are needed to achieve cost-efficient commercial products. At present, there are several available routes for the production of these materials but few allow large-scale manufacturing and environmentally friendly low-cost solvents are rarely used. We have previously demonstrated a scalable and low-cost industrial route to produce nanographites by tube-shearing in water suspensions. However, for a deeper understanding of the exfoliation mechanism, how and where the actual exfoliation occurs must be known. This study investigates the effect of shear zone geometry, straight and helical coil tubes, on this system based on both numerical simulation and experimental data. The results show that the helical coil tube achieves a more efficient exfoliation with smaller and thinner flakes than the straight version. Furthermore, only the local wall shear stress in the turbulent flow is sufficient for exfoliation since the laminar flow contribution is well below the needed range, indicating that exfoliation occurs at the tube walls. This explains the exfoliation mechanism of water-based tube-shear exfoliation, which is needed to achieve scaling to industrial levels of few-layer graphene with known and consequent quality.
|
|
