| 1. |
- Akiba, K., et al.
(författare)
-
LHC forward physics
- 2016
-
Ingår i: Journal of Physics G: Nuclear and Particle Physics. - : IOP Publishing. - 0954-3899 .- 1361-6471. ; 43:11
-
Tidskriftsartikel (refereegranskat)
|
|
| 2. |
- Collins, P., et al.
(författare)
-
The LHCb VELO upgrade
- 2011
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576. ; 636, s. S185-S193
-
Tidskriftsartikel (refereegranskat)abstract
- The LHCb experiment at the LHC plans to massively increase its data taking capabilities by running at a higher luminosity with a fully upgraded detector around 2016. This scheme is independent of (but compatible with) the plans for the SLHC upgrades. The silicon detector will be upgraded to provide a 40 MHz readout and to be able to cope with the increased radiation environment. This paper describes the options currently under consideration. A highlight of the R&D so far undertaken is a beam test during summer 2009 using the Timepix chip to track charged particles. Preliminary results are presented, including a measurement of the resolution achieved by the 55 mu m pitch pixel array of better than 9.5 mu m for perpendicular tracks and 55 mu m for angled tracks.
|
|
| 3. |
- Akiba, K., et al.
(författare)
-
Measurement of thermal properties of the LHCb VELO detector using track-based software alignment
- 2023
-
Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 18:10
-
Tidskriftsartikel (refereegranskat)abstract
- The thermal properties of the LHCb Vertex Locator (VELO) are studied using the real-time detector alignment procedure. The variation of the position and orientation of the detector elements as a function of the operating temperature of the VELO is presented. This study uses a dataset collected by the LHCb experiment during a VELO temperature scan performed at the end of LHC Run 2 (October 2018). Significant shrinkage of the VELO modules is observed at the operating temperature of -30(degrees)C compared to the laboratory measurements on a single module taken at a range of temperatures from +45(degrees)C to -25(degrees)C. The thermal shrinkage expected from the extrapolation of laboratory measurements to lower temperatures, and the results of this alignment study are in good agreement.
|
|
| 4. |
- Akiba, K., et al.
(författare)
-
The LHCb VELO Upgrade module construction
- 2024
-
Ingår i: Journal of Instrumentation. - : Institute of Physics Publishing (IOPP). - 1748-0221. ; 19:6
-
Tidskriftsartikel (refereegranskat)abstract
- The LHCb detector has undergone a major upgrade for LHC Run 3. This Upgrade I detector facilitates operation at higher luminosity and utilises full-detector information at the LHC collision rate, critically including the use of vertex information. A new vertex locator system, the VELO Upgrade, has been constructed. The core element of the new VELO are the double-sided pixelated hybrid silicon detector modules which operate in vacuum close to the LHC beam in a high radiation environment. The construction and quality assurance tests of these modules are described in this paper. The modules incorporate 200 mu m thick, n -on -p silicon sensors bump-bonded to 130 nm technology ASICs. These are attached with high precision to a silicon microchannel substrate that uses evaporative CO 2 cooling. The ASICs are controlled and read out with flexible printed circuits that are glued to the substrate and wire -bonded to the chips. The mechanical support of the module is given by a carbon fibre plate, two carbon fibre rods and an aluminium plate. The sensor attachment was achieved with an average precision of 21 mu m, more than 99.5% of all pixels are fully functional, and a thermal figure of merit of 3 Kcm 2 W - 1 was achieved. The production of the modules was successfully completed in 2021, with the final assembly and installation completed in time for data taking in 2022.
|
|
