| 1. |
- Belaineh Yilma, Dagmawi, et al.
(författare)
-
Printable carbon-based supercapacitors reinforced with cellulose and conductive polymers
- 2022
-
Ingår i: Journal of Energy Storage. - : Elsevier Ltd. - 2352-152X .- 2352-1538. ; 50
-
Tidskriftsartikel (refereegranskat)abstract
- Sustainable electrical energy storage is one of the most important scientific endeavors of this century. Battery and supercapacitor technologies are here crucial, but typically the current state of the art suffers from either lack of large-scale production possibilities, sustainability or insufficient performance and hence cannot match growing demands in society. Paper and cellulosic materials are mature scalable templates for industrial roll-to-roll production. Organic materials, such as conducting polymers, and carbon derivatives are materials that can be synthesized or derived from abundant sources. Here, we report the combination of cellulose, PEDOT:PSS and carbon derivatives for bulk supercapacitor electrodes adapted for printed electronics. Cellulose provides a mesoscopic mesh for the organization of the active ingredients. Furthermore, the PEDOT:PSS in combination with carbon provides superior device characteristics when comparing to the previously standard combination of activated carbon and carbon black. PEDOT:PSS acts as a mixed ion-electron conducting glue, which physically binds activated carbon particles together, while at the same time facilitating swift transport of both electrons and ions. A surprisingly small amount (10%) of PEDOT:PSS is needed to achieve an optimal performance. This work shows that cellulose added to PEDOT:PSS-carbon enables high-performing, mechanically stable, printed supercapacitor electrodes using a combination of printing methods.
|
|
| 2. |
- Brooke, Robert, 1989-, et al.
(författare)
-
Large-scale paper supercapacitors on demand
- 2022
-
Ingår i: Journal of Energy Storage. - : Elsevier Ltd. - 2352-152X .- 2352-1538. ; 50
-
Tidskriftsartikel (refereegranskat)abstract
- Clean, sustainable electrical energy could be the next greatest challenge and opportunity of mankind. While the creation of clean energy has been proven, the storage of such energy requires much more research and development. Battery and energy storage technology today relies heavily on rare metals which cannot support large production needs of society. Therefore, the need for energy storage technology to be created sustainably is of great importance. Recently, conductive polymers, a class of organic materials, have shown impressive results in energy storage but requires further development if this technology is to be implemented in various energy storage applications. Here, we report a new ‘on demand’ design for supercapacitors that allows for individual devices in addition to devices in parallel and in series to increase the capacitance and voltage, respectively. The individual device showed impressive capacity up to 10 F while increasing the area with the large parallel device increased the capacitance to a record 127.8 F (332.8 mF/cm2). The ‘on demand’ design also allows paper supercapacitors to be in series to increase the operating voltage with an example device showing good charging behavior up to 5 V when 4 individual paper supercapacitors were arranged in series. Finally, the paper supercapacitors were incorporated into a prototype titled: ‘Norrkoping Starry Night’ which bridges the gap between art and science. An all-printed electrochromic display showing the city of Norrkoping, Sweden, complete with a touch sensor as an on/off switch and silicon solar cells to charge the paper supercapacitors is presented to bring several printed technologies together, highlighting the possibilities of the new paper supercapacitors within this report. © 2022
|
|
| 3. |
- Brooke, Robert, 1989-, et al.
(författare)
-
Nanocellulose and PEDOT:PSS composites and their applications
- 2023
-
Ingår i: Polymer Reviews. - : Taylor and Francis Ltd.. - 1558-3724 .- 1558-3716. ; :2, s. 437-
-
Tidskriftsartikel (refereegranskat)abstract
- The need for achieving sustainable technologies has encouraged research on renewable and biodegradable materials for novel products that are clean, green, and environmentally friendly. Nanocellulose (NC) has many attractive properties such as high mechanical strength and flexibility, large specific surface area, in addition to possessing good wet stability and resistance to tough chemical environments. NC has also been shown to easily integrate with other materials to form composites. By combining it with conductive and electroactive materials, many of the advantageous properties of NC can be transferred to the resulting composites. Conductive polymers, in particular poly(3,4-ethylenedioxythiophene:poly(styrene sulfonate) (PEDOT:PSS), have been successfully combined with cellulose derivatives where suspensions of NC particles and colloids of PEDOT:PSS are made to interact at a molecular level. Alternatively, different polymerization techniques have been used to coat the cellulose fibrils. When processed in liquid form, the resulting mixture can be used as a conductive ink. This review outlines the preparation of NC/PEDOT:PSS composites and their fabrication in the form of electronic nanopapers, filaments, and conductive aerogels. We also discuss the molecular interaction between NC and PEDOT:PSS and the factors that affect the bonding properties. Finally, we address their potential applications in energy storage and harvesting, sensors, actuators, and bioelectronics. © 2022 The Author(s).
|
|
| 4. |
- Brooke, Robert, 1989-, et al.
(författare)
-
Nanocellulose based carbon ink and its application in electrochromic displays and supercapacitors
- 2021
-
Ingår i: Flexible and Printed Electronics. - : IOP Publishing Ltd. - 2058-8585. ; 6:4
-
Tidskriftsartikel (refereegranskat)abstract
- Conventional electronics have been highlighted as a very unsustainable technology; hazardous wastes are produced both during their manufacturing but also, due to their limited recyclability, during their end of life cycle (e.g. disposal in landfill). In recent years additive manufacturing processes (i.e. screen printing) have attracted significant interest as a more sustainable approach to electronic manufacturing (printed electronics). Despite the field of printed electronics addressing some of the issues related to the manufacturing of electronics, many components and inks are still considered hazardous to the environment and are difficult to recycle. Here we present the development of a low environmental impact carbon ink based on a non-hazardous solvent and a cellulosic matrix (nanocellulose) and its implementation in electrochromic displays (ECDs) and supercapacitors. As part of the reported work, a different protocol for mixing carbon and cellulose nanofibrils (rotation mixing and high shear force mixing), nanocellulose of different grades and different carbon: nanocellulose ratios were investigated and optimized. The rheology profiles of the different inks showed good shear thinning properties, demonstrating their suitability for screen-printing technology. The printability of the developed inks was excellent and in line with those of reference commercial carbon inks. Despite the lower electrical conductivity (400 S m-1 for the developed carbon ink compared to 1000 S m-1 for the commercial inks), which may be explained by their difference in composition (carbon content, density and carbon derived nature) compared to the commercial carbon, the developed ink functioned adequately as the counter electrode in all screen-printed ECDs and even allowed for improved supercapacitors compared to those utilizing commercial carbon inks. In this sense, the supercapacitors incorporating the developed carbon ink in the current collector layer had an average capacitance = 97.4 mF cm-2 compared to the commercial carbon ink average capacitance = 61.6 mF cm-2. The ink development reported herein provides a step towards more sustainable printed green electronics. © 2021 The Author(s).
|
|
| 5. |
- Brooke, Robert, 1989-, et al.
(författare)
-
Paper Electronics Utilizing Screen Printing and Vapor Phase Polymerization
- 2023
-
Ingår i: Advanced Sustainable Systems. - : John Wiley and Sons Inc. - 2366-7486. ; 7:7
-
Tidskriftsartikel (refereegranskat)abstract
- The rise of paper electronics has been accelerated due to the public push for sustainability. Electronic waste can potentially be avoided if certain materials in electronic components can be substituted for greener alternatives such as paper. Within this report, it is demonstrated that conductive polymers poly(3,4-ethylenedoxythiophene) (PEDOT), polypyrrole, and polythiophene, can be synthesized by screen printing combined with vapor phase polymerization on paper substrates and further incorporated into functional electronic components. High patterning resolution (100 µm) is achieved for all conductive polymers, with PEDOT showing impressive sheet resistance values. PEDOT is incorporated as conductive circuitry and as the active material in all-printed electrochromic displays. The conductive polymer circuits allow for functional light emitting diodes, while the electrochromic displays are comparable to commercial displays utilizing PEDOT on plastic substrates.
|
|
| 6. |
- Chen, Shangzhi, et al.
(författare)
-
Redox-tunable structural colour images by UV-patterned conducting polymer nanofilms on metal surfaces
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- Precise manipulation of light-matter interaction has enabled a wide variety of approaches to create bright and vivid structural colours. Techniques utilizing photonic crystals, Fabry-Pérot cavities, plasmonics, or high-refractive index dielectric metasurfaces have been studied for applications ranging from optical coatings to reflective displays. However, complicated fabrication procedures for sub-wavelength nanostructures, limited active areas, and inherent absence of tunability of these approaches significantly impede their further development towards flexible, large-scale, and switchable devices compatible with facile and cost-effective production. Herein, we present a simple and efficient method to generate structural colours based on nanoscale conducting polymer films prepared on metallic surfaces via vapour phase polymerization and ultraviolet (UV) light patterning. Varying the UV dose enables synergistic control of both nanoscale film thickness and polymer permittivity, which generates controllable colours from violet to red. Together with greyscale photomasks this enables fabrication of high-resolution colour images using single exposure steps. We further demonstrate spatiotemporal tuning of the structurally coloured surfaces and images via electrochemical modulation of the polymer redox state. The simple structure, facile fabrication, wide colour gamut, and dynamic colour tuning make this concept competitive for future multi-functional and smart displays.
|
|
| 7. |
- Edberg, Jesper, 1988-, et al.
(författare)
-
A Forest-Based Triboelectric Energy Harvester
- 2022
-
Ingår i: Global Challenges. - : John Wiley and Sons Inc. - 2056-6646. ; 6:10
-
Tidskriftsartikel (refereegranskat)abstract
- Triboelectric nanogenerators (TENGs) are a new class of energy harvesting devices that have the potential to become a dominating technology for producing renewable energy. The versatility of their designs allows TENGs to harvest mechanical energy from sources like wind and water. Currently used renewable energy technologies have a restricted number of materials from which they can be constructed, such as metals, plastics, semiconductors, and rare-earth metals. These materials are all non-renewable in themselves as they require mining/drilling and are difficult to recycle at end of life. TENGs on the other hand can be built from a large repertoire of materials, including materials from bio-based sources. Here, a TENG constructed fully from wood-derived materials like lignin, cellulose, paper, and cardboard, thus making it 100% green, recyclable, and even biodegradable, is demonstrated. The device can produce a maximum voltage, current, and power of 232 V, 17 mA m–2, and 1.6 W m–2, respectively, which is enough to power electronic systems and charge 6.5 µF capacitors. Finally, the device is used in a smart package application as a self-powered impact sensor. The work shows the feasibility of producing renewable energy technologies that are sustainable both with respect to their energy sources and their material composition. © 2022 The Authors.
|
|
| 8. |
- Edberg, Jesper, 1988-, et al.
(författare)
-
A Paper‐Based Triboelectric Touch Interface : Toward Fully Green and Recyclable Internet of Things
- 2023
-
Ingår i: Advanced Sensor Research. - : Wiley. - 2751-1219. ; 2:1
-
Tidskriftsartikel (refereegranskat)abstract
- The transition to a sustainable society is driving the development of green electronic solutions designed to have a minimal environmental impact. One promising route to achieve this goal is to construct electronics from biobased materials like cellulose, which is carbon neutral, non‐toxic, and recyclable. This is especially true for internet‐of‐things devices, which are rapidly growing in number and are becoming embedded in every aspect of our lives. Here, paper‐based sensor circuits are demonstrated, which use triboelectric pressure sensors to help elderly people communicate with the digital world using an interface in the form of an electronic “book”, which is more intuitive to them. The sensors are manufactured by screen printing onto flexible paper substrates, using in‐house developed cellulose‐based inks with non‐hazardous solvents. The triboelectric sensor signal, generated by the contact between a finger and chemically modified cellulose, can reach several volts, which can be registered by a portable microcontroller card and transmitted by Bluetooth to any device with an internet connection. Apart from the microcontroller (which can be easily removed), the whole system can be recycled at the end of life. A triboelectric touch interface, manufactured using printed electronics on flexible paper substrates, using cellulose‐based functional inks is demonstrated. These metal‐free green electronics circuits are implemented in an “electronic book” demonstrator, equipped with wireless communication that can control remote devices, as a step toward sustainable and recyclable internet‐of‐things devices.
|
|
| 9. |
- Edberg, Jesper, 1988-
(författare)
-
Flexible and Cellulose-based Organic Electronics
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Organic electronics is the study of organic materials with electronic functionality and the applications of such materials. In the 1970s, the discovery that polymers can be made electrically conductive led to an explosion within this field which has continued to grow year by year. One of the attractive features of organic electronic materials is their inherent mechanical flexibility, which has led to the development of numerous flexible electronics technologies such as organic light emitting diodes and solar cells on flexible substrates. The possibility to produce electronics on flexible substrates like plastic or paper has also had a large impact on the field of printed, electronics where inks with electronic functionality are used for large area fabrication of electronic devices using classical printing methods, such as screen printing, inkjet printing and flexography.Recently, there has been a growing interest in the use of cellulose in organic and printed electronics, not only as a paper substrate but also as a component in composite materials where the cellulose provides mechanical strength and favorable 3D-microstructures. Nanofibrillated cellulose is composed of cellulose fibers with high aspect-ratio and diameters in the nanometer range. Due to its remarkable mechanical strength, large area-to-volume ratio, optical transparency and solution processability it has been widely used as a scaffold or binder for electronically active materials in applications such as batteries, supercapacitors and optoelectronics.The focus of this thesis is on flexible devices based on conductive polymers and can be divided into two parts: (1) Composite materials of nanofibrillated cellulose and the conductive polymer PEDOT:PSS and (2) patterning of vapor phase polymerized conductive polymers. In the first part, it is demonstrated how the combination of cellulose and conductive polymers can be used to make electronic materials of various form factors and functionality. Thick, freestanding and flexible “papers” are used to realize electrochemical devices such as transistors and supercapacitors while lightweight, porous and elastic aerogels are used for sensor applications. The second focus of the thesis is on a novel method of patterning conductive polymers produced by vapor phase polymerization using UV-light. This method is used to realize flexible electrochromic smart windows with high-resolution images and tunable optical contrast.
|
|
| 10. |
- Fall, Andreas, et al.
(författare)
-
Spinning of Stiff and Conductive Filaments from Cellulose Nanofibrils and PEDOT:PSS Nanocomplexes
- 2022
-
Ingår i: ACS Applied Polymer Materials. - : American Chemical Society (ACS). - 2637-6105. ; 4:6, s. 4119-4130
-
Tidskriftsartikel (refereegranskat)abstract
- Research in smart textiles is growing due to the increased demand from the healthcare sector and people's urge to keep track of and analyze the signals and metrics from their bodies. Electrically conductive filaments are the most fundamental material for smart textiles. These filaments can be imbued with functionalities and useful in fields like energy storage, sensing, and actuation. To be able to meet the requirements that the latter applications require, fabrication techniques must be developed to provide better processability and sustainability in a cost-effective manner. Here, a mixture of a conductive polymer, poly(3,4-ethylenedioxythiophene) (PEDOT), and biobased cellulose nanofibrils (CNFs) was used to spin filaments utilizing a water-based process. These filaments show electrical conductivities up to 150 S/cm and tensile stiffness of 20 GPa. Interestingly, the PEDOT aligned to a similar degree as the CNFs during the spinning process without a drawing step, which is hypothesized to be caused by the attachment of PEDOT on the CNFs. Lastly, the filaments were tested in an organic electrochemical transistor (OECT) configuration, which resulted in a working device with an on/off ratio approaching 1500. Furthermore, the OECT exhibited stable behavior when changing temperature (20-80 °C) and relative humidity (40-80%). This aqueous spinning method, resulting in filaments with robust electronic properties in different temperature and humidity environments, show greats promise for future innovative smart textiles.
|
|
