| 1. |
- Ederth, Thomas, et al.
(författare)
-
A neutron reflectivity study of drainage and stratification of AOT foam films
- 2003
-
Ingår i: Langmuir. - : American Chemical Society (ACS). - 0743-7463 .- 1520-5827. ; 19:19, s. 7727-7733
-
Tidskriftsartikel (refereegranskat)abstract
- Structural properties of Aerosol-OT (AOT) foam films were studied by neutron reflectometry. The drainage of large (10 cm(2)), horizontally oriented AOT films under zero applied external pressure is slow and proceeds from thick colored or gray films to black films of approximately 200 Angstrom thickness over many hours, resulting in quasi-static conditions over the time scales required for the acquisition of reflectivity profiles throughout the whole drainage process. After formation of the foam film-while still showing colored interference fringes-and during the early stages of thinning, the appearance of Bragg diffraction peaks demonstrates that the film contains multilamellar structure, in agreement with studies at free air/water interfaces. Upon further reduction of the film thickness, below approximately 250 Angstrom, the reflectivity profile is well fitted by a three-layer slab model with two surfactant layers and an aqueous core with a high surfactant content. The composition of the aqueous core and the manner in which the reflectivity during the latter stages of draining evolves from Bragg peaks to a Kiessig fringe structure indicate stratification within the thin foam film.
|
|
| 2. |
- Wanzhu, Cai, et al.
(författare)
-
Dedoping-induced interfacial instability of poly(ethylene imine)s-treated PEDOT:PSS as a low-work-function electrode
- 2020
-
Ingår i: Journal of Materials Chemistry C. - : ROYAL SOC CHEMISTRY. - 2050-7526 .- 2050-7534. ; 8:1, s. 328-336
-
Tidskriftsartikel (refereegranskat)abstract
- Transparent organic electrodes printed from high-conductivity PEDOT:PSS have become essential for upscaling all-carbon based, low-cost optoelectronic devices. In the printing process, low-work-function PEDOT:PSS electrodes (cathode) are achieved by coating an ultra-thin, non-conjugated polyelectrolyte that is rich in amine groups, such as poly(ethylene imine) (PEI) or its ethoxylated derivative (PEIE), onto PEDOT:PSS surfaces. Here, we mapped the physical and chemical processes that occur at the interface between thin PEIx (indicating either PEI or PEIE) and PEDOT:PSS during printing. We identify that there is a dedoping effect of PEDOT induced by the PEIx. Using infrared spectroscopy, we found that the amine-rich PEIx can form chemical bonds with the dopant, PSS. At lower PSS concentration, PEIx also shows an electron-transfer effect to the charged PEDOT chain. These interface reactions lock the surface morphology of PEDOT:PSS, preventing the redistribution of PSS, and reduce the work function. Subsequent exposure to oxygen during the device fabrication process, on the other hand, can result in redoping of the low-work-function PEDOT:PSS interface, causing problems for printing reproducible devices under ambient conditions.
|
|
| 3. |
- Yeung, Sing Yee, et al.
(författare)
-
Reversible Self-Assembled Monolayers (rSAMs) as Robust and Fluidic Lipid Bilayer Mimics
- 2018
-
Ingår i: Langmuir. - : American Chemical Society (ACS). - 0743-7463 .- 1520-5827. ; 34:13, s. 4107-4115
-
Tidskriftsartikel (refereegranskat)abstract
- Lipid bilayers, forming the outer barrier of cells, display a wide array of proteins and carbohydrates for modulating interfacial biological interactions. Formed by the spontaneous self-assembly of lipid molecules, these bilayers feature liquid crystalline order, while retaining a high degree of lateral mobility. Studies of these dynamic phenomena have been hampered by the fragility and instability of corresponding biomimetic cell membrane models. Here, we present the construct of a series of oligoethylene glycol-terminated reversible self-assembled monolayers (rSAMs) featuring lipid-bilayer-like fluidity, while retaining air and protein stability and resistance. These robust and ordered layers were prepared by simply immersing a carboxylic acid terminated self-assembled monolayer into 5-50 mu M aqueous omega-(4-ethylene glycol-phenoxy)-alpha-(4-amidinophenoxy)decane solutions. It is anticipated that this new class of robust and fluidic two-dimensional biomimetic surfaces will impact the design of rugged cell surface mimics and high-performance biosensors.
|
|
| 4. |
- Ahmed, Fareed, et al.
(författare)
-
Manufacturing Poly(3,4-Ethylenedioxythiophene) Electrocatalytic Sheets for Large-Scale H2O2 Production
- 2022
-
Ingår i: Advanced Sustainable Systems. - : John Wiley and Sons Inc. - 2366-7486. ; 6:1
-
Tidskriftsartikel (refereegranskat)abstract
- Producing thick films of conducting polymers by a low-cost manufacturing technique would enable new applications. However, removing huge solvent volume from diluted suspension or dispersion (1–3 wt%) in which conducting polymers are typically obtained is a true manufacturing challenge. In this work, a procedure is proposed to quickly remove water from the conducting polymer poly(3,4-ethylenedioxythiophene:poly(4-styrene sulfonate) (PEDOT:PSS) suspension. The PEDOT:PSS suspension is first flocculated with 1 m H2SO4 transforming PEDOT nanoparticles (≈50–500 nm) into soft microparticles. A filtration process inspired by pulp dewatering in a paper machine on a wire mesh with apertures dimension between 60 µm and 0.5 mm leads to thick free-standing films (≈0.5 mm). Wire mesh clogging that hinders dewatering (known as dead-end filtration) is overcome by adding to the flocculated PEDOT:PSS dispersion carbon fibers that aggregate and form efficient water channels. Moreover, this enables fast formation of thick layers under simple atmospheric pressure filtration, thus making the process truly scalable. Thick freestanding PEDOT films thus obtained are used as electrocatalysts for efficient reduction of oxygen to hydrogen peroxide, a promising green chemical and fuel. The inhomogeneity of the films does not affect their electrochemical function. © 2021 The Authors.
|
|
| 5. |
- Ail, Ujwala, et al.
(författare)
-
Thermoelectric Properties of Polymeric Mixed Conductors
- 2016
-
Ingår i: Advanced Functional Materials. - : Wiley-VCH Verlagsgesellschaft. - 1616-301X .- 1616-3028. ; 26:34, s. 6288-6296
-
Tidskriftsartikel (refereegranskat)abstract
- The thermoelectric (TE) phenomena are intensively explored by the scientific community due to the rather inefficient way energy resources are used with a large fraction of energy wasted in the form of heat. Among various materials, mixed ion-electron conductors (MIEC) are recently being explored as potential thermoelectrics, primarily due to their low thermal conductivity. The combination of electronic and ionic charge carriers in those inorganic or organic materials leads to complex evolution of the thermovoltage (Voc) with time, temperature, and/or humidity. One of the most promising organic thermoelectric materials, poly(3,4-ethyelenedioxythiophene)-polystyrene sulfonate (PEDOT-PSS), is an MIEC. A previous study reveals that at high humidity, PEDOT-PSS undergoes an ionic Seebeck effect due to mobile protons. Yet, this phenomenon is not well understood. In this work, the time dependence of the Voc is studied and its behavior from the contribution of both charge carriers (holes and protons) is explained. The presence of a complex reorganization of the charge carriers promoting an internal electrochemical reaction within the polymer film is identified. Interestingly, it is demonstrated that the time dependence behavior of Voc is a way to distinguish between three classes of polymeric materials: electronic conductor, ionic conductor, and mixed ionic–electronic conductor
|
|
| 6. |
- Ajjan, Fátima, et al.
(författare)
-
Spectroelectrochemical investigation of redox states in a polypyrrole/lignin composite electrode material
- 2015
-
Ingår i: Journal of Materials Chemistry A. - : ROYAL SOC CHEMISTRY. - 2050-7488 .- 2050-7496. ; 3:24, s. 12927-12937
-
Tidskriftsartikel (refereegranskat)abstract
- We report spectroelectrochemical studies to investigate the charge storage mechanism of composite polypyrrole/lignin electrodes. Renewable bioorganic electrode materials were produced by electropolymerization of pyrrole in the presence of a water-soluble lignin derivative acting as a dopant. The resulting composite exhibited enhanced charge storage abilities due to a lignin-based faradaic process, which was expressed after repeated electrochemical redox of the material. The in situ FTIR spectroelectrochemistry results show the formation of quinone groups, and reversible oxidation-reduction of these groups during charge-discharge experiments in the electrode materials. The most significant IR bands include carbonyl absorption near 1705 cm(-1), which is attributed to the creation of quinone moieties during oxidation, and absorption at 1045 cm(-1) which is due to hydroquinone moieties.
|
|
| 7. |
- Aldred, Nick, et al.
(författare)
-
Confocal microscopy-based goniometry of barnacle cyprid permanent adhesive
- 2013
-
Ingår i: Journal of Experimental Biology. - : Company of Biologists. - 0022-0949 .- 1477-9145. ; 216:11, s. 1969-1972
-
Tidskriftsartikel (refereegranskat)abstract
- Biological adhesives are materials of particular interest in the fields of bio-inspired technology and antifouling research. The adhesive of adult barnacles has received much attention over the years; however, the permanent adhesive of the cyprid - the colonisation stage of barnacles - is a material about which very little is presently known. We applied confocal laser-scanning microscopy to the measurement of contact angles between the permanent adhesive of barnacle cyprid larvae and self-assembled monolayers of OH- and CH3-terminated thiols. Measurement of contact angles between actual bioadhesives and surfaces has never previously been achieved and the data may provide insight into the physicochemical properties and mechanism of action of these functional materials. The adhesive is a dual-phase system post-secretion, with the behaviour of the components governed separately by the surface chemistry. The findings imply that the cyprid permanent adhesion process is more complex than previously thought, necessitating broad re-evaluation of the system. Improved understanding will have significant implications for the production of barnacle-resistant coatings as well as development of bio-inspired glues for niche applications.
|
|
| 8. |
|
|
| 9. |
- Andersson, Olof, 1978-
(författare)
-
Imaging surface plasmon resonance
- 2008
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The central theme of this thesis is the use of imaging Surface Plasmon Resonance (iSPR) as a tool in the characterization of surfaces with laterally varying properties. Within the scope of this work, an instrument for iSPR analysis was designed and built. SPR is a very sensitive technique for monitoring changes in optical properties in the immediate vicinity of a sensor surface, which is very useful in biosensing and surface science research. We have employed SPR in the Kretschmann configuration, wherein surface plasmons are excited by means of an evanescent field arising from total internal reflection from the backside of the sensor surface. In iSPR, the signal is the reflectivity of TM-polarized light which is measured using an imaging detector, typically a CCD camera. Advantages of this technique include extreme surface sensitivity and, because detection is done from the backside, compatibility with complex samples. In addition, SPR is a non-labeling technique, and in imaging mode, a lateral resolution in the µm range can be attained.The imaging SPR instrument could be operated in either wavelength interrogation mode or in intensity mode. In the former case, the objective is to find the SPR wave-length, λSPR, which is the wavelength at which the reflected intensity is at a minimum. In intensity mode, a snapshot of the intensity reflectance is taken at a fixed wavelength hand incidence angle.In biosensor science, the use of an imaging technique offers a major advantage by enabling parallelization and thereby increasing throughput. We have, for example, used iSPR in biochemical interaction analysis to monitor immobilization and specific binding to protein and synthetic polypeptide micro arrays. The primary interest has been the study of soft matter surfaces that possess properties interesting in the field of biomimetics or for applications in biosensing. Specifically, the surfaces studied in this thesis include patterned self-assembled monolayers of thiolates on gold, a graft polymerized poly(ethylene glycol) (PEG) based hydrogel, a dextran hydrogel, and a polyelectrolyte charge gradient. Our results show that the PEG-based hydrogel is very well suited for use as a platform in protein immobilization in an array format, owing to the very low unspecific binding. In addition, well defined microarray templates were designed by patterning of hydrophobic barriers on dextran and monolayer surfaces. A polypeptide affinity microarray was further designed and immobilized on such a patterned monolayer substrate, in order to demonstrate the potential of analyte quantification with high sensitivity over a large dynamic range.Furthermore, iSPR was combined with electrochemistry to enable laterally resolved studies of electrochemical surface reactions. Using this combination, the electrochemical properties of surfaces patterned with self assembled monolayers can be studied in parallel, with a spatial resolution in the µm regime. We have also employed electrochemistry and iSPR for the investigation of potential and current density gradients on bipolar electrodes.The imaging SPR instrument could be operated in either wavelength interrogation mode or in intensity mode. In the former case, the objective is to find the SPR wave-length, λSPR, which is the wavelength at which the reflected intensity is at a minimum. In intensity mode, a snapshot of the intensity reflectance is taken at a fixed wavelength hand incidence angle.In biosensor science, the use of an imaging technique offers a major advantage by enabling parallelization and thereby increasing throughput. We have, for example, used iSPR in biochemical interaction analysis to monitor immobilization and specific binding to protein and synthetic polypeptide micro arrays. The primary interest has been the study of soft matter surfaces that possess properties interesting in the field of biomimetics or for applications in biosensing. Specifically, the surfaces studied in this thesis include patterned self-assembled monolayers of thiolates on gold, a graft polymerized poly(ethylene glycol) (PEG) based hydrogel, a dextran hydrogel, and a polyelectrolyte charge gradient. Our results show that the PEG-based hydrogel is very well suited for use as a platform in protein immobilization in an array format, owing to the very low unspecific binding. In addition, well defined microarray templates were designed by patterning of hydrophobic barriers on dextran and monolayer surfaces. A polypeptide affinity microarray was further designed and immobilized on such a patterned monolayer substrate, in order to demonstrate the potential of analyte quantification with high sensitivity over a large dynamic range.Furthermore, iSPR was combined with electrochemistry to enable laterally resolved studies of electrochemical surface reactions. Using this combination, the electrochemical properties of surfaces patterned with self assembled monolayers can be studied in parallel, with a spatial resolution in the µm regime. We have also employed electrochemistry and iSPR for the investigation of potential and current density gradients on bipolar electrodes.
|
|
| 10. |
- Bittoun, Eyal, et al.
(författare)
-
Filled Nanoporous Surfaces : Controlled Formation and Wettability
- 2009
-
Ingår i: LANGMUIR. - : American Chemical Society (ACS). - 0743-7463 .- 1520-5827. ; 25:20, s. 12374-12379
-
Tidskriftsartikel (refereegranskat)abstract
- The controlled filling of hydrophobic nanoporous surfaces with hydrophilic molecules and their wetting properties are described and demonstrated by using thiocholesterol (TC) self-assembled monolayers (SAMs) on gold and mercaptoundecanoic acid (MUA) as the filling agent. A novel procedure was developed for filling the nanopores in the TC SAMs by immersing them into a "cocktail" solution of TC and MUA, with TC in huge excess. This procedure results in an increasing coverage of MUA with increasing immersion time up to an area fraction of similar to 23%, while the amount of TC remains almost constant. Our findings strongly support earlier observations where linear omega-substituted alkanethiols selectively fill defects (nanopores) in the TC SAM (Yang et al. Langmuir 1997, 12, 1704-1707). They also support the formation of a homogeneously mixed SAM, given by the distribution of TC on the gold surface, rather than of a phase-segregated overlayer structure with domains of varying size, shape, and composition. The wetting properties of the Filled SAMs were investigated by measuring the most stable contact angle as well as contact angle hysteresis. It is shown that the most stable contact angle is very well described by the Cassie equation, since the drops arc much larger than the scale of chemical heterogeneity of the SAM surfaces. In addition, it is demonstrated that contact angle hysteresis is sensitive to the chemical heterogeneity of the surface, even at the nanometric scale.
|
|
