| 1. |
|
|
| 2. |
|
|
| 3. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 4. |
- Luo, Yifei, et al.
(författare)
-
Technology Roadmap for Flexible Sensors
- 2023
-
Ingår i: ACS Nano. - : American Chemical Society. - 1936-0851 .- 1936-086X. ; 17:6, s. 5211-5295
-
Forskningsöversikt (refereegranskat)abstract
- Humans rely increasingly on sensors to address grand challenges and to improve quality of life in the era of digitalization and big data. For ubiquitous sensing, flexible sensors are developed to overcome the limitations of conventional rigid counterparts. Despite rapid advancement in bench-side research over the last decade, the market adoption of flexible sensors remains limited. To ease and to expedite their deployment, here, we identify bottlenecks hindering the maturation of flexible sensors and propose promising solutions. We first analyze challenges in achieving satisfactory sensing performance for real-world applications and then summarize issues in compatible sensor-biology interfaces, followed by brief discussions on powering and connecting sensor networks. Issues en route to commercialization and for sustainable growth of the sector are also analyzed, highlighting environmental concerns and emphasizing nontechnical issues such as business, regulatory, and ethical considerations. Additionally, we look at future intelligent flexible sensors. In proposing a comprehensive roadmap, we hope to steer research efforts towards common goals and to guide coordinated development strategies from disparate communities. Through such collaborative efforts, scientific breakthroughs can be made sooner and capitalized for the betterment of humanity.
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Akhtar, Farid, et al.
(författare)
-
Effect of adding a type of binder phase on the microstructure, properties and heat treatment of steel bonded TiC cermets
- 2007
-
Ingår i: Progress in powder metallurgy. - Uetikon-Zürich : Trans Tech Publications Inc.. ; , s. 1161-1164
-
Konferensbidrag (refereegranskat)abstract
- Particulate TiC reinforced 465 maraging stainless steel matrix Cermets were processed by conventional P/M. The binder phase was added in the form of elemental powders and master alloy powders. The microstructures, binder phase variation with TiC content and mechanical properties were evaluated. The addition of a type of binder phase largely effects the microstructure and mechanical properties. When a master alloy binder phase was used the microstructure showed interphase debondings, microcracks and large growths of TiC particles. Where as, elemental powders in the composition of binder phases showed defect free microstructure of steel bonded cermets. The binder phase variation from starting composition was observed with increase in wt% TiC content and this variation was higher when the master alloy powders were used as a binder. After heat treatment and aging, an increase in hardness was observed. The increase in hardness was attributed to the aging reaction in maraging stainless steel. The response to heat treatment was decreased with an increase in TiC content due to the shift of binder phase from the starting composition.
|
|
| 9. |
- Clark, Andrew G., et al.
(författare)
-
Evolution of genes and genomes on the Drosophila phylogeny
- 2007
-
Ingår i: Nature. - : Springer Science and Business Media LLC. - 0028-0836 .- 1476-4687. ; 450:7167, s. 203-218
-
Tidskriftsartikel (refereegranskat)abstract
- Comparative analysis of multiple genomes in a phylogenetic framework dramatically improves the precision and sensitivity of evolutionary inference, producing more robust results than single-genome analyses can provide. The genomes of 12 Drosophila species, ten of which are presented here for the first time (sechellia, simulans, yakuba, erecta, ananassae, persimilis, willistoni, mojavensis, virilis and grimshawi), illustrate how rates and patterns of sequence divergence across taxa can illuminate evolutionary processes on a genomic scale. These genome sequences augment the formidable genetic tools that have made Drosophila melanogaster a pre-eminent model for animal genetics, and will further catalyse fundamental research on mechanisms of development, cell biology, genetics, disease, neurobiology, behaviour, physiology and evolution. Despite remarkable similarities among these Drosophila species, we identified many putatively non-neutral changes in protein-coding genes, non-coding RNA genes, and cis-regulatory regions. These may prove to underlie differences in the ecology and behaviour of these diverse species.
|
|
| 10. |
- Feng, Pei Zhong, et al.
(författare)
-
Study on Oxidation Behavior of (W, Mo) Si2 Powders in Air at 400, 500 and 600textordmasculineC
- 2007
-
Ingår i: Progress in powder metallurgy. - Uetikon-Zürich : Trans Tech Publications Inc.. ; , s. 1289-1292
-
Konferensbidrag (refereegranskat)abstract
- The oxidation of (W,Mo)Si2 powders has been examined at 400, 500 and 600°C for 12.0 hours in air. It was shown that the low temperature oxidation resistance of (W,Mo)Si2 was worse than that of MoSi 2, and they showed great changes in mass, volume and colour. At 500°C, the amount of volume expansion of (W,Mo)Si2 was as high as about 7-8 times and color changed from black to yellow after 4.0h with MoO 3, WO3, (W,Mo)O3 and amorphous SiO2 as main reaction products. It took about 8.0h to obtain the same results for MoSi2. The mass gain and oxidation rate were relatively slower at 400°C and 600°C than that at 500°C These were probably due to the lower oxidation rate at 400°C and the protective silica glass on surface of powders formed from the volatilization of MoO3, WO3 and (W,Mo)O3 at 600°C, which would restrain the diffusion of molybdenum from matrix to exterior and oxygen from outside to inside and the further accelerated oxidation.
|
|
