| 1. |
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
- Amani, Mozhdeh, et al.
(författare)
-
Shear Behavior of Stainless Steel Girders with Corrugated Webs
- 2022
-
Ingår i: Proc. of Stainless Steel in Structures – Sixth International Experts Seminar.
-
Konferensbidrag (refereegranskat)abstract
- This paper reports experimental and finite element investigations conducted to assess the shear strength of corrugated web girders in stainless steel. The steel under consideration is LDX 2101. Four trapezoidal corrugated web girders were tested under shear. All tested girders reached the shear yield strength followed by strain hardening. An imperfection sensitivity study was done with the aid of finite element modelling. It was observed that an initial geometric imperfection based on the first eigen buckling mode with a maximum amplitude of the minimum dimension of the critical corrugation sub panel divided by 200, ?max200⁄, leads to an ultimate shear strength greater than the shear yield strength and close to the test findings. It is concluded that EN 1993-1-5 shear design model for corrugated webs is conservative for stainless steel girders tested in the current study.
|
|
| 7. |
- Amani, Mozhdeh, 1985, et al.
(författare)
-
Shear behavior of stainless steel girders with corrugated webs
- 2023
-
Ingår i: Journal of constructional steel research. - : Elsevier Ltd. - 0143-974X .- 1873-5983. ; 210
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, the shear strength of corrugated web girders made of EN 1.4162/LDX 2101 stainless steel is investigated. Four full-scale trapezoidal corrugated web girders were tested under shear. Before conducting the tests, DIC was used to measure the real geometric imperfections in the web panels. Complementary finite element analysis studies were conducted to assess the sensitivity of the shear strength to initial imperfections. The experimental results indicated that all the tested girders with a local slenderness ratio of λ = 0.7 attained the shear yield strength, which was then followed by strain hardening in the material at a level that was 8–18% higher than the yield strength. This implies that the Eurocode's limit of λ = 0.25 to attain the plastic shear strength in corrugated webs can be quite conservative for stainless steel. According to the findings of the imperfection sensitivity studies, an initial geometric imperfection based on the first eigen buckling mode and with a maximum amplitude of amax/200, where amax is the maximum corrugation fold length, yielded ultimate strength within 3% of the test results. When the amplitude was increased to hw/200, where hw is the web height, the ultimate strength was estimated to be 25% lower on average than in the experiments. In three of the studied girders, initial imperfections with other forms than the first buckling mode were found to be more critical. Further, it was found that regardless of mode number, mode shapes that are more extended over the web panel result in a higher degradation of the ultimate shear strength. © 2023 The Authors
|
|
| 8. |
-
Analysis of the Flexural Behavior of Textile Reinforced Reactive Powder Concrete Sandwich Elements Using Optical Measurements
- 2018
-
Proceedings (redaktörskap) (refereegranskat)abstract
- Prefabricated and non-load bearing sandwich façade elements were developed using Textile Reinforced Reactive Powder Concrete (TRRPC) along with low density Foamed Concrete (FC) and Glass Fiber Reinforced Polymer (GFRP) continuous connecting devices. Four-point bending tests were performed on large-scale TRRPC sandwich element beams to characterize the structural performance, which included the flexural capacity, level of composite action, resulting deformation, crack propagation and failure mechanisms. Optical measurements based on Digital Image Correlation (DIC) were taken simultaneously to enable a detailed analysis of the underlying composite action. The structural behavior of the developed elements was found to be highly dependent on the stiffness and strength of the connectors to ensure composite action between the two TRRPC panels.
|
|
| 9. |
|
|
| 10. |
- Bergström, Gunnar, et al.
(författare)
-
Acceptanskriterier för repor och intryck i plaströr Accpetance criteria for scratches and indentations in plastic pipes
- 2009
-
Rapport (refereegranskat)abstract
- Development of materials and laying techniques have arisen the question how scratches and indentations in plastics pipes affect the strength and technical lifetime of pipelines. Scratches may occur both in the manufacturing of the pipes, in connection with the installation and subsequent maintenance. The problems in assessing the failure risk from scratches and indentations are similar for pipes used in gas and water distribution and in district heating applications. Therefore, a broad effort to identify the risks in relation to current pipe materials is technically and economically justified. The project has aimed to evaluate the effect of scratches and indentations on the technical lifetime of plastics pipes and to present criteria for maximum allowable depth of scratches and indentations. The study on pressure pipes focused on the conditions for scratched polyethylene pipes to achieve a lifetime of 50 years. It is noted that a scratch damage can not be judged solely on the basis of its depth and sharpness. To assess the impact of the scratch on the serviceability of the pipe, consideration must also be taken to the material from which the pipe was made and the safety factor used in the design. Extensive pressure tests show that pipes made of modern materials can withstand surface scratches to a higher degree than pipes of older materials. For pipes made of modern bimodal PE80 and PE100 materials, scratches up to 10% depth may be accepted without reduction of rated pressure. However, for pipes of older material, a reduction in pressure may be required already at smaller scratches. The study also indicates that for the same relative scratch depth, a greater reduction in pressure is required with increasing pipe dimension. The study on the non pressure pipes shows that the studied polypropylene pipes resist both deep scratches combined with ovalization and large indentations without any cracks penetrating the pipe wall. However, the extent and development of crazing and surface cracking vary with scratch depth, deformation level and material. The test pipes were subjected to extreme conditions very rarely or never occurring in practice. This suggests that small scratches at moderate ovalization and realistic indentations in temperatures around room temperature do not affect the lifetime of the pipes. One objective of the project was to develop a method for the evaluation of the scratch resistance of a pipe. In the proposed test method the force needed to produce a specified scratch is measured. This force is used as a relative measure of the scratch resistance of a pipe material when compared to other materials. In order to assess to what extent a scratch affects the lifetime of the pipe, the depth of the scratch must be estimated with reasonable accuracy. Since the scratch in many cases is found on existing pipelines the method must be suited for field use. To achieve that a simple instrument for scratch depth measurements was made and evaluated.
|
|
