| 1. |
- Alnegren, Patrik, 1988, et al.
(författare)
-
Inhibiting chromium evaporation and oxide scale growth on SOFC metallic interconnects by nano coatings
- 2014
-
Ingår i: 20th World Hydrogen Energy Conference, WHEC 2014. - 9780000000002 ; 1:2014
-
Konferensbidrag (refereegranskat)abstract
- High chromium ferritic steel is today the most commonly considered material for SOFC interconnectors due to many desirable properties, such as matching thermal expansion coefficient with other cell components but most importantly better machinability and price compared to ceramic alternatives. Yet there are some obstacles that need to be addressed before long term stability of a ferritic steel interconnector based fuel cell stack can be realized. First of all the electrical conductivity needs to remain high throughout the fuel cell stack operating life time and thus the formed oxide layers need to be electrically conductive and thin. Secondly, volatilization of chromium from the oxide scale of metallic interconnects causes rapid degradation due cathode poisoning. In the current study both oxidation and chromium evaporation of ferritic steel substrates are investigated in controlled atmospheres that simulates the environments of an operating SOFC stack. Samples coated with nanometer scale dual coatings of Co and Ce were tested. The dual coating substantially increased the performance of the ferritic substrates by i) significantly reducing oxidation rate, ii) increasing scale adherence and iii) diminishing chromium evaporation by 90 % via the formation of a Co-Mn-spinel cap layer.
|
|
| 2. |
- Alnegren, Patrik, 1988, et al.
(författare)
-
Degradation of ferritic stainless steels under conditions used for solid oxide fuel cells and electrolyzers at varying oxygen pressures
- 2016
-
Ingår i: Corrosion Science. - : Elsevier BV. - 0010-938X. ; 110, s. 200-212
-
Tidskriftsartikel (refereegranskat)abstract
- Four commercial ferritic stainless steels were tested at 850 °C in oxygen pressures ranging from 10-4 to 1 atm, in order to investigate the isolated effect of oxygen pressure on corrosion, in the context of solid oxide electrolysis cells. The oxidation rates of all steels were essentially independent of oxygen partial pressure, which indicates n-type behavior. FIB/SEM analysis revealed that the grain size of the oxides was found to decrease at lower oxygen pressures. Volatile Cr species evaporation in pure oxygen was significantly lower than what has been reported for simulated solid oxide fuel cell environments with humid air.
|
|
| 3. |
- Alnegren, Patrik, 1988, et al.
(författare)
-
Severe dual atmosphere effect at 600 °C for stainless steel 441
- 2016
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 301, s. 170-178
-
Tidskriftsartikel (refereegranskat)abstract
- AISI 441 foils of 0.2 mm thickness were exposed in a dual atmosphere setup in which one side was exposed to air -3% H2O and the other to Ar -5% H2 - 3% H2O. The experiment was performed at 600 °C and was referenced against exposures in air +3% H2O on both sides. The exposure conditions were chosen to simulate the conditions of an interconnect in intermediate temperature solid oxide fuel cell stacks (IT-SOFC). A strong dual atmosphere effect was observed: local breakaway corrosion was discovered after only 1000 h on samples exposed to dual atmospheres. After 3000 h iron oxide had propagated to cover the entire surface area of the sample. In comparison, the samples exposed in single atmosphere formed thin protective chromia scales on both sides even after 3000 h of exposure.
|
|
| 4. |
- Alnegren, Patrik, 1988, et al.
(författare)
-
Temperature dependence of corrosion of ferritic stainless steel in dual atmosphere at 600–800 °C
- 2018
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 392, s. 129-138
-
Tidskriftsartikel (refereegranskat)abstract
- The ferritic stainless steel AISI 441 (EN 1.4509) is exposed for 1000 h to air - 3% H2O on one side and to Ar - 5% H2 – 3% H2O on the other at temperatures 600, 700, and 800 °C. Conditions are chosen to mimic the environment of metallic interconnects in an operating solid oxide fuel cell (SOFC). At 600 °C, ∼25 μm thick Fe2O3/(Fe,Cr)3O4 forms on large parts of the air side of the samples. Reference samples exposed to air - 3% H2O on both sides form thin protective layers of (Cr,Mn)3O4/Cr2O3 at the same temperature. At higher temperatures, 700 and 800 °C, all samples form protective layers of (Cr,Mn)3O4/Cr2O3 regardless of exposure to single or dual atmosphere. It is concluded that corrosion resistance in a dual atmosphere has an inverse dependence on temperature. Different hypotheses for the underlying cause for the dual atmosphere effect are discussed and compared to the experimental data.
|
|
| 5. |
- Falk Windisch, Hannes, 1984, et al.
(författare)
-
Chromium vaporization from mechanically deformed pre-coated interconnects in Solid Oxide Fuel Cells
- 2015
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 297, s. 217-223
-
Tidskriftsartikel (refereegranskat)abstract
- Cathode poisoning, associated with Cr evaporation from interconnect material, is one of the most important degradation mechanisms in Solid Oxide Fuel Cells when Cr2O3-forming steels are used as the interconnect material. Coating these steels with a thin Co layer has proven to decrease Cr vaporization. To reduce production costs, it is suggested that thin metallic PVD coatings be applied to each steel strip before pressing the material into interconnect shape. This process would enable high volume production without the need for an extra post-coating step. However, when the pre-coated material is mechanically deformed, cracks may form and lower the quality of the coating. In the present study, Chromium volatilization is measured in an air-3% H2O environment at 850 C for 336 h. Three materials coated with 600 nm Co are investigated and compared to an uncoated material. The effect of deformation is investigated on real interconnects. Microscopy observations reveal the presence of cracks in the order of several μm on the deformed pre-coated steel. However, upon exposure, the cracks can heal and form a continuous surface oxide rich in Co and Mn. As an effect of the rapid healing, no increase in Cr vaporization is measured for the pre-coated material.
|
|
| 6. |
- Falk Windisch, Hannes, 1984, et al.
(författare)
-
Co- and Ce/Co-coated ferritic stainless steel as interconnect material for Intermediate Temperature Solid Oxide Fuel Cells
- 2017
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 343, s. 1-10
-
Tidskriftsartikel (refereegranskat)abstract
- Chromium species volatilization, oxide scale growth, and electrical scale resistance were studied at 650 and 750 °C for thin metallic Co- and Ce/Co-coated steels intended to be utilized as the interconnect material in Intermediate Temperature Solid Oxide Fuel Cells (IT-SOFC). Mass gain was recorded to follow oxidation kinetics, chromium evaporation was measured using the denuder technique and Area Specific Resistance (ASR) measurements were carried out on 500 h pre-exposed samples. The microstructure of thermally grown oxide scales was characterized using Scanning Electron Microscopy (SEM), Scanning Transmission Electron Microscopy (STEM), and Energy Dispersive X-Ray Analysis (EDX). The findings of this study show that a decrease in temperature not only leads to thinner oxide scales and less Cr vaporization but also to a significant change in the chemical composition of the oxide scale. Very low ASR values (below 10 m? cm2) were measured for both Co- and Ce/Co-coated steel at 650 and 750 °C, indicating that the observed change in the chemical composition of the Co spinel does not have any noticeable influence on the ASR. Instead it is suggested that the Cr2O3 scale is expected to be the main contributor to the ASR, even at temperatures as low as 650 °C.
|
|
| 7. |
- Falk Windisch, Hannes, 1984, et al.
(författare)
-
Determination of the oxide scale growth mechanism using 18O-tracer experiments in combination with Transmission Electron Microscopy and nanoscale Secondary Ion Mass Spectrometry
- 2018
-
Ingår i: Materials Characterization. - : Elsevier BV. - 1044-5803. ; 136, s. 128-133
-
Tidskriftsartikel (refereegranskat)abstract
- Two-stage 18 O 2 / 16 O 2 exposures can be used to investigate the effect that alloying elements, secondary phases, or surface treatments have on the high temperature oxidation behaviour of certain materials. During subsequent exposures to 16 O 2 - and 18 O 2 -rich atmospheres, 16 O- and 18 O-rich layers are formed. Analysis of the layers using Seco ndary Ion Mass Spectrometry (SIMS) depth profiling allows for conclusions to be drawn about the oxide scale growth mechanism. The conclusions are, however, not entirely unambiguous due to the limited lateral resolution of the technology. Rough surface topography and the thickness variation of the oxide scale over the analysed volume add to the ambiguity of the findings. In this study, an Fe-20%Cr alloy was exposed to both 18 O- and 16 O-rich environments at 850 °C. Two methods were used to analyse the thermally grown Cr 2 O 3 scale: (1) traditional SIMS depth profiling and (2) preparation of a cross-sectional lamellae for Transmission Electron Microscopy (TEM), which, subsequently, was analysed in a NanoSIMS. The NanoSIMS 16 O and 18 O elemental maps were then superimposed on the TEM image. In comparison with traditional SIMS depth profiling, the nanoSIMS elemental maps reveal detailed information about local oxide growth in different parts of an oxide scale. Moreover, a clear 16 O/ 18 O interface can be seen in the nanoSIMS maps, which is not the case in the sputter depth profiles. The findings of this study show that the aforementioned issues associated with sputter depth profiling can be eliminated by mapping a cross-section of an oxide scale using high resolution nanoSIMS.
|
|
| 8. |
- Froitzheim, Jan, 1981, et al.
(författare)
-
Investigation of Chromium Volatilization from FeCr Interconnects by a Denuder Technique
- 2010
-
Ingår i: Journal of the Electrochemical Society. - : The Electrochemical Society. - 1945-7111 .- 0013-4651. ; 157:9, s. B1295-B1300
-
Tidskriftsartikel (refereegranskat)abstract
- A technique is presented for accurate and time-resolved quantification of chromium volatilization from alloys at high temperature. A denuder tube which is coated with Na2CO3 is placed downstream of the samples. CrO2(OH)(2) that evaporated from the samples is collected on the denuder and converted to the thermally stable Na2CrO4. The chromate is then dissolved in water and determined quantitatively. Three commercially available ferritic 22% Cr steels intended for use as solid oxide fuel cell interconnect materials (Sanergy HT, Crofer 22 APU, and ZMG 232) have been investigated with respect to chromium volatilization and oxidation rate. The effect on chromium volatilization of a submicrometer cobalt coating on the steel surface is reported. Comparisons are made with a conventional thick ceramic coating. The experiments are carried out at 850 degrees C in N-2 - 20% O-2 - 3% H2O atmosphere. The submicrometer Co coatings proved to be very efficient, reducing Cr volatilization by 1 order of magnitude. Microscopic studies show that both uncoated steel and steel coated with a submicrometer cobalt film develop two-layered oxide scales with the bottom part consisting of a Cr-rich corundum-type oxide. The uncoated samples develop a top layer consisting of (Cr, Mn)(3)O-4 oxide, whereas the Co-coated samples exhibit a top layer consisting of Co-rich spinel oxide. (C) 2010 The Electrochemical Society. [DOI: 10.1149/1.3462987] All rights reserved.
|
|
| 9. |
- Grolig, Jan Gustav, 1986, et al.
(författare)
-
Coated stainless steel 441 as interconnect material for solid oxide fuel cells: Evolution of electrical properties
- 2015
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 284, s. 321-327
-
Tidskriftsartikel (refereegranskat)abstract
- AISI 441 coated. with a double layer coating of 10 nm cerium (inner layer) and 630 nm cobalt was investigated and in addition the uncoated material was exposed for comparison. The main purpose of this investigation was the development of a suitable ASR characterization method. The material was exposed to a simulated cathode atmosphere of air with 3% water at 850 degrees C and the samples were exposed for up to 1500 h. We compared two methods of ASR measurements, an in-situ method where samples were measured with platinum electrodes for longer exposure times and an ex-situ method where pre-oxidized samples were measured for only very short measurement times. It was found that the ASR of ex-situ characterized samples could be linked to the mass gain and the electrical properties could be linked to the evolving microstructure during the different stages of exposure. Both the degradation of the electric performance and the oxygen uptake (mass gain) followed similar trends. After about 1500 h of exposure an ASR value of about 15 m Omega cm(2) was reached. The in-situ measured samples suffered from severe corrosion attack during measurement. After only 500 h of exposure already a value of 35 m Omega cm(2) was obtained.
|
|
| 10. |
- Grolig, Jan Gustav, 1986, et al.
(författare)
-
Coated stainless steel 441 as interconnect material for solid oxide fuel cells: Oxidation performance and chromium evaporation
- 2014
-
Ingår i: Journal of Power Sources. - : Elsevier BV. - 0378-7753. ; 248, s. 1007-1013
-
Tidskriftsartikel (refereegranskat)abstract
- Reactive Element (RE) and RE/cobalt-coated stainless steel AISI 441 was exposed at Solid Oxide Fuel Cell (SOFC) cathode conditions (850 degrees C in air with 3% water content) for up to 500 h. The chromium evaporation was measured by applying the denuder technique. Uncoated material exhibited severe spallation which could be successfully prevented by using cerium or lanthanum coatings. By applying double layer coatings of cerium or lanthanum in combination with cobalt the oxidation rate was decreased and the chromium volatilisation was also about 90% lower than the uncoated material.
|
|
