| 1. |
- Cornelio, Roberto Belloti, et al.
(författare)
-
The influence of bis-EMA vs bis GMA on the degree of conversion and water susceptibility of experimental composite materials
- 2014
-
Ingår i: Acta Odontologica Scandinavica. - : Informa UK Limited. - 0001-6357 .- 1502-3850. ; 72:6, s. 440-447
-
Tidskriftsartikel (refereegranskat)abstract
- Objective. The aim of this work was to assess the influence of the bis-EMA content on the degree of conversion (DC) and its effect on the water sorption and solubility. Materials and methods. In a polytetrafluorethylene (PTFE) mould, 30 samples (O = 5 mm, height = 2 mm) of four experimental dental composite resins were cured for 10 s, 20 s and 40 s. The DC was analysed by Fourier Transform (FT)-Raman spectroscopy. To analyse sorption and solubility, six samples (O = 15 mm and thickness = 1 mm) of each composite (n = 72) were stored in water at 37 degrees C for different storage periods: 24 h, 7 days and 30 days. Results. When cured for 20 or 40 s the DC increased with the increasing content of bis-EMA. However, the presence of 15 wt% of bis-GMA did not affect the DC, except when cured with 10 s irradiation time. This study also found a correlation between the content of bis-EMA and the reduced values for sorption and solubility, for all storage times used, when the materials were cured with 20 s. Conclusions. The DC of mixtures with higher content of bis-EMA is affected by the presence of bis-GMA at lower energy density delivered from the curing device, suggesting that the restrictions caused by the presence of hydrogen bonds is dependent of the irradiation time used.
|
|
| 2. |
- Wikant, A. W., et al.
(författare)
-
Suboptimal light curing and direct exposure to water of two contemporary composites: degree of conversion, sorption, solubility, and Knoop hardness
- 2020
-
Ingår i: European Journal of Oral Sciences. - : Wiley. - 0909-8836 .- 1600-0722. ; 128:4, s. 345-353
-
Tidskriftsartikel (refereegranskat)abstract
- The water sorption and solubility of two polymer resin-based dental composite materials were assessed in order to evaluate the effects of immediate post-cure water exposure on the water sensitivity of the composites. Each material was tested with two different light curing setups. The radiant exposure of the two curing setups differed by a factor of 5. After exposure to water and subsequent drying, the Knoop surface hardness was measured. The change in the degree of conversion in both water and air storage medium within the first 24 h after curing was monitored by Raman spectroscopy. No significant differences in the degree of conversion were detected 24 h after curing. Samples exposed to the lower irradiation dose showed higher solubility and a lower surface hardness than the samples exposed to the higher irradiation dose. Early exposure to water did not cause detectable differences in the ongoing polymerization process. Increase in radiant exposure reduced the fraction of unbound constituents and increased the crosslink density, thereby reducing the plasticity of the material.
|
|
| 3. |
- Akhlaghi, Shahin
(författare)
-
Degradation of acrylonitrile butadiene rubber and fluoroelastomers in rapeseed biodiesel and hydrogenated vegetable oil
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Biodiesel and hydrotreated vegetable oil (HVO) are currently viewed by the transportation sector as the most viable alternative fuels to replace petroleum-based fuels. The use of biodiesel has, however, been limited by the deteriorative effect of biodiesel on rubber parts in automobile fuel systems. This work therefore aimed at investigating the degradation of acrylonitrile butadiene rubber (NBR) and fluoroelastomers (FKM) on exposure to biodiesel and HVO at different temperatures and oxygen concentrations in an automated ageing equipment and a high-pressure autoclave. The oxidation of biodiesel at 80 °C was promoted by an increase in the oxygen partial pressure, resulting in the formation of larger amounts of hydroperoxides and acids in the fuel. The fatty acid methyl esters of the biodiesel oxidized less at 150 °C on autoclave aging, because the termination reactions between alkyl and alkylperoxyl radicals dominated over the initiation reactions. HVO consists of saturated hydrocarbons, and remained intact during the exposure. The NBR absorbed a large amount of biodiesel due to fuel-driven internal cavitation in the rubber, and the uptake increased with increasing oxygen partial pressure due to the increase in concentration of oxidation products of the biodiesel. The absence of a tan δ peak (dynamical mechanical measurements) of the bound rubber and the appearance of carbon black particles devoid of rubber suggested that the cavitation was caused by the detachment of bound rubber from particle surfaces. A significant decrease in the strain-at-break and in the Payne-effect amplitude of NBR exposed to biodiesel was explained as being due to the damage caused by biodiesel to the rubber-carbon-black network. During the high-temperature autoclave ageing, the NBR swelled less in biodiesel, and showed a small decrease in the strain-at-break due to the cleavage of rubber chains. The degradation of NBR in the absence of carbon black was due only to biodiesel-promoted oxidative crosslinking. The zinc cations released by the dissolution of zinc oxide particles in biodiesel promoted reduction reactions in the acrylonitrile part of the NBR. Heat-treated star-shaped ZnO particles dissolved more slowly in biodiesel than the commercial ZnO nanoparticles due to the elimination of inter-particle porosity by heat treatment. The fuel sorption was hindered in HVO-exposed NBR by the steric constraints of the bulky HVO molecules. The extensibility of NBR decreased only slightly after exposure to HVO, due to the migration of plasticizer from the rubber. The bisphenol-cured FKM co- and terpolymer swelled more than the peroxide-cured GFLT-type FKM in biodiesel due to the chain cleavage caused by the attack of biodiesel on the double bonds formed during the bisphenol curing. The FKM rubbers absorbed biodiesel faster, and to a greater extent, with increasing oxygen concentration. It is suggested that the extensive biodiesel uptake and the decrease in the strain-at-break and Young’s modulus of the FKM terpolymer was due to dehydrofluorination of the rubber by the coordination complexes of biodiesel and magnesium oxide and calcium hydroxide particles. An increase in the CH2-concentration of the extracted FKM rubbers suggested that biodiesel was grafted onto the FKM at the unsaturated sites resulting from dehydrofluorination.
|
|
| 4. |
- Akhlaghi, Shahin, et al.
(författare)
-
Degradation of carbon-black-filled acrylonitrile butadiene rubber in alternative fuels : Transesterified and hydrotreated vegetable oils
- 2016
-
Ingår i: Polymer degradation and stability. - : Elsevier. - 0141-3910 .- 1873-2321. ; 123, s. 69-79
-
Tidskriftsartikel (refereegranskat)abstract
- The deterioration of acrylonitrile butadiene rubber (NBR), a common sealing material in automobile fuel systems, when exposed to rapeseed biodiesel and hydrotreated vegetable oil (HVO) was studied. The fuel sorption was hindered in HVO-exposed rubber by the steric constraints of bulky HVO molecules, but it was promoted in biodiesel-exposed rubber by fuel-driven cavitation in the NBR and by the increase in diffusivity of biodiesel after oxidation. The absence of a tan δ peak of the bound rubber and the appearance of carbon black particles devoid of rubber suggested that the cavitation was made possible in biodiesel-aged rubber by the detachment of bound rubber from particle surfaces. The HVO-exposed NBR showed a small decrease in strain-at-break due to the migration of plasticizer from the rubber, and a small increase in the Young’s modulus due to oxidative crosslinking. A drastic decrease in extensibility and Payne-effect amplitude of NBR on exposure to biodiesel was explained as being due to the damage caused by biodiesel to the continuous network of bound rubber-carbon black. A decrease in the ZnO crystal size with increasing exposure time suggested that the particles are gradually dissolved in the acidic components of oxidized biodiesel. The Zn2+ cations released from the dissolution of ZnO particles in biodiesel promoted the hydrolysis of the nitrile groups of NBR.
|
|
| 5. |
- Akhlaghi, Shahin, et al.
(författare)
-
Degradation of fluoroelastomers in rapeseed biodiesel at different oxygen concentrations
- 2017
-
Ingår i: Polymer degradation and stability. - : Elsevier. - 0141-3910 .- 1873-2321. ; 136, s. 10-19
-
Tidskriftsartikel (refereegranskat)abstract
- The degradation of fluoroelastomers (FKM) based on different monomers, additives and curing systems was studied after exposure to rapeseed biodiesel at 100 °C and different oxygen partial pressures. The sorption of fuel in the carbon black-filled FKM terpolymer was promoted by the fuel-driven cavitation in the rubber. The bisphenol-cured rubbers swelled more in biodiesel than the peroxide-cured FKM, presumably due to the chain cleavage caused by the attack of biodiesel on the double bonds formed during the bisphenol curing. With any of the selected types of monomer, the FKM rubbers absorbed biodiesel faster and to a greater extent with increasing oxygen partial pressure due to the increase in concentration of the oxidation products of biodiesel. Water-assisted complexation of biodiesel on magnesium oxide and calcium hydroxide particles led to dehydrofluorination of FKM, resulting in an extensive fuel uptake and a decrease in the strain-at-break and the Young's modulus of the rubbers. An increase in the CH2-concentration determined by infrared spectroscopy, and the appearance of biodiesel flakes in scanning electron micrographs of the extracted rubbers, were explained as being due to the presence of insoluble biodiesel grafted onto FKM on the unsaturated sites resulting from dehydrofluorination. The extensibility of the GFLT-type FKM was the least affected on exposure to biodiesel because this rubber contained less unsaturation and metal oxide/hydroxide particles.
|
|
| 6. |
- Akhlaghi, Shahin, et al.
(författare)
-
Deterioration of acrylonitrile butadiene rubber in rapeseed biodiesel
- 2015
-
Ingår i: Polymer degradation and stability. - : Elsevier BV. - 0141-3910 .- 1873-2321. ; 111, s. 211-222
-
Tidskriftsartikel (refereegranskat)abstract
- The deterioration of acrylonitrile butadiene rubber (NBR) exposed to rapeseed biodiesel at 90 degrees C was studied. The oxidation of biodiesel and NBR during ageing was monitored by H-1 NMR and infrared spectroscopy, HPLC and titration methods. The oxidation of biodiesel was impeded in the presence of NBR, but promoted in biodiesel-exposed rubber. This was explained as being due to the migration of stabilizer from the rubber to biodiesel, the diffusion of dissolved oxygen from biodiesel into NBR and the absorption of oxidation precursors of biodiesel by the rubber. The resemblance between the anomalous sorption kinetics of biodiesel in NBR and the equilibrium benzene uptake by the aged rubbers revealed that biodiesel caused a network defect in NBR, resulting in a gradual increase in the equilibrium swelling. The cleavage of crosslinks was implausible since the Young's modulus of the rubber at low strains, disregarding an initial decrease, increased with increasing exposure time. The appearance of 'naked' carbon black particles in the scanning electron micrographs of the aged rubbers and a drastic decrease in the strain-at-break of NBR after exposure to biodiesel suggests that internal cavitation was caused by the attack of biodiesel on the acrylonitrile units of NBR.
|
|
| 7. |
- Akhlaghi, Shahin, et al.
(författare)
-
Deterioration of automotive rubbers in liquid biofuels : A review
- 2015
-
Ingår i: Renewable & sustainable energy reviews. - : Elsevier BV. - 1364-0321 .- 1879-0690. ; 43, s. 1238-1248
-
Forskningsöversikt (refereegranskat)abstract
- Concerns over the fast depletion of fossil fuels, environmental issues and stringent legislation associated with petroleum-based fuels have triggered a shift to bio-based fuels, as an alternative to meet the growing energy demand in the transportation sector. However, since conventional automobile fuel systems are adapted to petroleum-based fuels, switching to biofuels causes a severe deterioration in the performance of currently used rubber components. The degradation of the rubber materials in biofuels is complicated by the presence of different additives in biofuels and rubber compounds, by oxidation of biofuels and by the effects of thermomechanical loadings in the engine. This paper presents a comprehensive review of the effects of different types of biofuels, particularly biodiesel and bioethanol, on the physical, mechanical, morphological and thermal properties of elastomers under different exposure conditions. In addition, the literature data available on the variation of rubbers' resistance to biofuels with the changes in their monomer type and composition, cure system and additives content was also studied. The review essentially focuses on the compatibility of biofuels with acrylonitrile butadiene rubber, fluoroelastomers, polychloroprene rubber and silicon rubber, as the most commonly used automotive rubbers coming into contact with fuels during their service. The knowledge summarized in this study can help to develop a guideline on the selection of rubber for automotive parts designed to withstand biofuels.
|
|
| 8. |
- Akhlaghi, Shahin, et al.
(författare)
-
Effects of ageing conditions on degradation of acrylonitrile butadiene rubber filled with heat-treated ZnO star-shaped particles in rapeseed biodiesel
- 2017
-
Ingår i: Polymer degradation and stability. - : Elsevier. - 0141-3910 .- 1873-2321.
-
Tidskriftsartikel (refereegranskat)abstract
- The degradation of acrylonitrile butadiene rubber (NBR) after exposure to biodiesel at different oxygen partial pressures in an automated ageing equipment at 80 °C, and in a high-pressure autoclave at 150 °C was studied. The oxidation of biodiesel was promoted by an increase in oxygen concentration, resulting in a larger uptake of fuel in the rubber due to internal cavitation, a greater decrease in the strain-at-break of NBR due to the coalescence of cavity, and a faster increase in the crosslinking density and carbonyl index due to the promotion of the oxidation of NBR. During the high-temperature autoclave ageing, less fuel was absorbed in the rubber, because the formation of hydroperoxides and acids was impeded. The extensibility of NBR aged in the autoclave decreased only slightly due to the cleavage of rubber chains by the biodiesel attack. The degradation of NBR in the absence of carbon black was explained as being due to oxidative crosslinking. The dissolution of ZnO crystals in the acidic components of biodiesel was retarded by removing the inter-particle porosity and surface defects through heat treating star-shaped ZnO particles. The rubber containing heat-treated ZnO particles swelled less in biodiesel than a NBR filled with commercial ZnO nanoparticles, and showed a smaller decrease in the strain-at-break and less oxidative crosslinking.
|
|
| 9. |
- Alipour, Nazanin, 1978-
(författare)
-
Structure and Mechanical/Transport properties of Single and Multilayer Polyethylene-based Materials
- 2014
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The current study discusses the structure, mechanical and transport properties of polyethylene-based materials into two parts. The first part deals with the migration and chemical depletion of active substance such as insecticides from moulded polyethylene sheets. Deltamethrin (DM) and synergist piperonyl butoxide (PBO) are often used for insect control purpose. It was found that DM as a powder was incapable of recrystallization and remained in liquid state after cooling to room temperature, and that the evaporation of a DM/PBO solution was greater than that predicted from the evaporation rates of pristine separate material components. Infrared spectroscopy and liquid chromatography showed that the loss of DM and PBO through polyethylene sheets was negligible over 30 days, when aged in air at 80 °C (60 and 80 %RH). However, significant migration of the active species was observed in aged polyethylene sheets which were exposed in liquid water (at 80 and 95 °C). In the second part, the structure and properties of multi–layered polymer films were studied in terms of crystallization kinetics, mechanical and transport properties. Previously, it has been shown that when the layer thickness decreases from micrometre-scale to nanometre-scale, leading to improvement of the film performance such as crack propagation and oxygen barrier properties. In this work, two multi-layered systems were considered based on compatible (i) or incompatible layers (ii). In the first case (i), metallocene polyethylene (mPE) and low-density polyethylene (LDPE) where investigated as 2, 24, and 288 adjacent layers. In the second case (ii) poly(ethylene-co-vinyl alcohol) (EVOH) and polyethylene adhesive was evaluated as 5 and 19 layers. The crystallization kinetic studies showed that the crystallization rate was retarded as the layers became thinner with increasing number of layers in the multi-layered films as compared to the reference films (2 and 5 layers). The observation was suggested to stem from greater association between layers (inter layer mixing) in the case of mPE/LDPE films with 2 layers. Furthermore, the crack growth resistance increased with increasing number of layers. The x-ray scattering and tensile testing showed that the films were orientated more in extrusion direction than in the transverse direction, besides the EVOH films (the incompatible system) showed higher orientation in the extrusion direction than mPE/LDPE films. The uptake of n-hexane was reduced significantly in multi-layered EVOH films due to the effective protective role of EVOH. Furthermore, it was revealed that non-homogenous swelling causing a folding/curling of bilayer films when exposed to the vapour of the solvent.
|
|
| 10. |
- Alipour, Nazanin, et al.
(författare)
-
Structure and properties of polyethylene-based and EVOH-based multilayered films with layer thicknesses of 150 nm and greater
- 2015
-
Ingår i: European Polymer Journal. - : Elsevier BV. - 0014-3057 .- 1873-1945. ; 64, s. 36-51
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents the structure and properties of two multilayered systems where polymers in adjacent layers were either miscible or immiscible. The miscible system consisted of 2, 17, 18, 24 and nominally 288 layers of alternating low-density (LDPE) and low-density/linear-low density (mPE) polyethylene layers with observed thicknesses ranging from 150 nm to 20 urn. The immiscible system consisted of 5 and 19 layer films with a combination of poly(ethylene-co-vinyl alcohol) (EVOH) (thickness: 9 and 1 gm, respectively), LDPE (17 and 7 gm) and a polyethylene adhesive (3 and 1 gm). The purpose of the multi-layering was to increase the crack growth resistance and, in the EVOH-based system, to decrease the oxygen transmission rate. Indeed, the crack growth resistance, as measured on tensile-tested notched films, increased with increasing number of layers. The thinnest polyethylene and polyethylene adhesive layers showed a clear ductile failure when fractured even in liquid nitrogen. Simultaneous synchrotron wide-angle/small-angle X-ray scattering and tensile testing indicated no new deformation features with changes in the layer thickness. The oxygen permeability was the same in the 5- and 19-layer EVOH-based films, but the uptake of n-hexane was strongly reduced in the 19-layer films, demonstrating the effective protective role of the EVOH layers. The n-hexane desorption data of the 2-layer LDPE/mPE film was successfully modeled using the diffusivities and solubilities of the single layers. Crystallization was slower and more confined in the films with thinner layers. The interlayer mixing in the melt (measured by isothermal crystallization from melts of initially layered polyethylene-based systems) was, as expected, significantly faster in the 24- and 288-multilayer films than in the 2-layer film.
|
|
