| 1. |
- Hu, Q., et al.
(författare)
-
Effect of Mo on high-temperature strength of refractory complex concentrated alloys: A perspective of electronegativity difference
- 2022
-
Ingår i: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388. ; 906
-
Tidskriftsartikel (refereegranskat)abstract
- Refractory complex concentrated alloys, RCCAs, show great potential for ultrahigh-temperature applications. High-temperature strength is one of the key requirements for RCCAs to qualify for that purpose. Some RCCAs already show superior high-temperature strength than that of commercial Ni-based superalloys, but many other RCCAs do not. It is thus important to identify the key factors that control the high-temperature strength of RCCAs. In this work, based on a statistic analysis of the yield strength at 1000 °C (σy1000) for 55 reported RCCAs, interestingly, it is revealed that Mo-containing RCCAs have in general a higher σy1000 than those RCCAs not containing Mo. The effect of Mo is attributed to its larger electronegativity and hence the larger electronegativity difference to other alloying elements, rather than to its higher melting point. The previously established proposal that a large electronegativity difference favoring the charge transfer and creating an atomic-level pressure that contributes to the strengthening of RCCAs at room temperature, seems effective even at a high temperature of 1000 °C. In addition, the large electronegativity difference also favors the room-temperature strength of single-bcc-phase RCCAs. The findings from this work, further verified experimentally in six new RCCAs, shed light on new research directions to develop RCCAs with decent strength at both high temperatures and room temperature, using a simple descriptor on the electronegativity difference.
|
|
| 2. |
- Ng, C, et al.
(författare)
-
Phase stability and tensile properties of Co-free Al 0.5CrCuFeNi2 high-entropy alloys
- 2014
-
Ingår i: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388. ; 584, s. 530-537
-
Tidskriftsartikel (refereegranskat)abstract
- High-entropy alloys (HEAs) are becoming new research frontiers in the metallic materials field. The phase stability of HEAs is of critical significance, but a convincing understanding on it has been somewhat held back by the slow diffusion kinetics, which prevents the completion of diffusion assisted phase transformations toward the equilibrium state. Here a unique methodology, combining both the thermomechanical treatments and thermodynamic calculations, was employed to reveal the phase stability of HEAs, exemplified using the newly developed Al0.5CrCuFeNi2 alloy. The metastable nature of the solid solution phases in this high-entropy alloy was uncovered through thermomechanical treatments induced phase transformations, and supported by the thermodynamic calculations. Meanwhile, the tensile properties for both the as-cast and thermomechanically treated alloys were measured, and correlated to their indentation behavior. © 2013 Published by Elsevier B.V.
|
|
| 3. |
- Ananthanarayanan, Durga, et al.
(författare)
-
Grain refinement in additively manufactured ferritic stainless steel by in situ inoculation using pre-alloyed powder
- 2021
-
Ingår i: Scripta Materialia. - : Elsevier BV. - 1359-6462 .- 1872-8456. ; 194
-
Tidskriftsartikel (refereegranskat)abstract
- For ferritic stainless steels, TiN has effectively been used as an inoculant to produce equiaxed grain structures in casting and welding. However, it is not established whether TiN would be an effective inoculant in additive manufacturing. In this study, the effectiveness of TiN as an inoculant in a ferritic stainless steel processed by laser powder-bed fusion is studied. An alloy without Ti is fabricated and compared to an alloy designed to form a high amount of TiN early during solidification. The work shows that the presence of TiN provides general grain refinement and that TiN-covered oxide particles are effective in enabling columnar-to-equiaxed transition in certain regions of the meltpool. The applied approach of pre-alloying powders with inoculant-forming elements offers a straightforward route to achieving fine, equiaxed grain structures in additively manufactured metallic materials. It also shows how oxygen present during the process can be utilized to nucleate effective inoculating phases.
|
|
| 4. |
- Balpande, A. R., et al.
(författare)
-
Excellent specific strength-ductility synergy in novel complex concentrated alloy after suction casting
- 2024
-
Ingår i: Materials and Design. - 1873-4197 .- 0264-1275. ; 242
-
Tidskriftsartikel (refereegranskat)abstract
- Lightweight alloys are known to improve the fuel efficiency of the structural components due to high strength-to-weight ratio, however, they lack formability at room temperature. This major limitation of poor formability is most of the time overcome by post-fabrication processing and treatments thereby increasing their cost exponentially. We present a novel Ti50V16Zr16Nb10Al5Mo3 (all in at. %) complex concentrated alloy (Ti-CCA) designed based on the combination of valence electron concentration theory and the high entropy approach. The optimal selection of constituent elements has led to a density of 5.63 gm/cc for Ti-CCA after suction casting (SC). SC Ti-CCA displayed exceptional room temperature strength (UTS ∼ 1.25 GPa) and ductility (ε ∼ 35 %) with a yield strength (YS) of ∼ 1.1 GPa (Specific YS = 191 MPa/gm/cc) without any post-processing treatments. The exceptional YS in Ti-CCA is attributed to hetero grain size microstructure, whereas enormous strength-ductility synergy is due to the concurrent occurrence of slip and deformation band formation in the early stages of deformation followed by prolonged necking event due to delayed void nucleation and growth. The proposed philosophy of Ti-CCA design overcomes the conventional notion of strength-ductility trade-off in such alloy systems by retaining their inherent characteristics.
|
|
| 5. |
- Bhattacharjee, T., et al.
(författare)
-
Effect of low temperature on tensile properties of AlCoCrFeNi2.1 eutectic high entropy alloy
- 2018
-
Ingår i: Materials Chemistry and Physics. - : Elsevier BV. - 0254-0584. ; 210, s. 207-212
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of low temperature on tensile properties of a AlCoCrFeNi 2.1 eutectic high entropy alloy (EHEA) was investigated in the present work. Transmission electron microscopy (TEM) showed that the initial as-cast microstructure consisted of B2 (ordered body centered cubic structure) and L1 2 (ordered face centered cubic structure) phases. Upon tensile testing at temperatures ranging from room temperature (RT) to −196 °C (77 K), the L1 2 phase became disordered, changing to a simple FCC (face centered cubic) crystal structure whereas the B2 phase maintained an ordered structure. An increase over 300 MPa was observed in the ultimate tensile strength (σ UTS ) of the −196 °C tensile tested sample compared to the room temperature tensile tested sample, while keeping almost similar amount of total elongation. TEM results indicated an increase in the dislocation activity in the FCC phase as well as B2 phase in the −196 °C tensile tested sample compared to the sample deformed at room temperature.
|
|
| 6. |
- Bhattacharjee, T., et al.
(författare)
-
Simultaneous Strength-Ductility Enhancement of a Nano-Lamellar AlCoCrFeNi2.1 Eutectic High Entropy Alloy by Cryo-Rolling and Annealing
- 2018
-
Ingår i: Scientific Reports. - : Springer Science and Business Media LLC. - 2045-2322 .- 2045-2322. ; 8:1
-
Tidskriftsartikel (refereegranskat)abstract
- Nano-lamellar (L1 2 + B2) AlCoCrFeNi 2.1 eutectic high entropy alloy (EHEA) was processed by cryo-rolling and annealing. The EHEA developed a novel hierarchical microstructure featured by fine lamellar regions consisting of FCC lamellae filled with ultrafine FCC grains (average size ∼200-250 nm) and B2 lamellae, and coarse non-lamellar regions consisting of ultrafine FCC (average size ∼200-250 nm), few coarse recrystallized FCC grains and rather coarse unrecrystallized B2 phase (∼2.5 μm). This complex and hierarchical microstructure originated from differences in strain-partitioning amongst the constituent phases, affecting the driving force for recrystallization. The hierarchical microstructure of the cryo-rolled and annealed material resulted in simultaneous enhancement in strength (Yield Strength/YS: 1437 ± 26 MPa, Ultimate Tensile Strength/UTS: 1562 ± 33 MPa) and ductility (elongation to failure/e f ∼ 14 ± 1%) as compared to the as-cast as well as cold-rolled and annealed materials. The present study for the first time demonstrated that cryo-deformation and annealing could be a novel microstructural design strategy for overcoming strength-ductility trade off in multiphase high entropy alloys.
|
|
| 7. |
- Dong, Y. B., et al.
(författare)
-
The growth of graphene on Ni–Cu alloy thin films at a low temperature and its carbon diffusion mechanism
- 2019
-
Ingår i: Nanomaterials. - : MDPI AG. - 2079-4991. ; 9:11
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon solid solubility in metals is an important factor affecting uniform graphene growth by chemical vapor deposition (CVD) at high temperatures. At low temperatures, however, it was found that the carbon diffusion rate (CDR) on the metal catalyst surface has a greater impact on the number and uniformity of graphene layers compared with that of the carbon solid solubility. The CDR decreases rapidly with decreasing temperatures, resulting in inhomogeneous and multilayer graphene. In the present work, a Ni–Cu alloy sacrificial layer was used as the catalyst based on the following properties. Cu was selected to increase the CDR, while Ni was used to provide high catalytic activity. By plasma-enhanced CVD, graphene was grown on the surface of Ni–Cu alloy under low pressure using methane as the carbon source. The optimal composition of the Ni–Cu alloy, 1:2, was selected through experiments. In addition, the plasma power was optimized to improve the graphene quality. On the basis of the parameter optimization, together with our previously-reported, in-situ, sacrificial metal-layer etching technique, relatively homogeneous wafer-size patterned graphene was obtained directly on a 2-inch SiO2 /Si substrate at a low temperature (~600◦ C).
|
|
| 8. |
- Dong, Yibo, et al.
(författare)
-
In Situ Growth of CVD Graphene Directly on Dielectric Surface toward Application
- 2020
-
Ingår i: ACS Applied Electronic Materials. - : American Chemical Society (ACS). - 2637-6113. ; 2:1, s. 238-246
-
Tidskriftsartikel (refereegranskat)abstract
- A technique for the in situ growth of patterned graphene by CVD has been achieved directly on insulating substrates at 800 degrees C. The graphene growth is catalyzed by a Ni-Cu alloy sacrificial layer, which integrates many advantages such as being lithography-free, and almost wrinkle-free, with a high repeatability and rapid growth. The etching method of the metal sacrificial layer is the core of this technique, and the mechanism is analyzed. Graphene has been found to play an important role in accelerating etching speeds. The Ni-Cu alloy exhibits a high catalytic activity, and thus, high-quality graphene can be obtained at a lower temperature. Moreover, the Ni-Cu layer accommodates a limited amount of carbon atoms, which ensures a high monolayer ratio of the graphene. The carbon solid solubility of the alloy is calculated theoretically and used to explain the experimental findings. The method is compatible with the current semiconductor process and is conducive to the industrialization of graphene devices.
|
|
| 9. |
- Dou, Bang, et al.
(författare)
-
Effect of Fe content on type and distribution of carbides in medium-entropy high-speed steels
- 2023
-
Ingår i: Tungsten. - : Springer Science and Business Media LLC. - 2661-8028 .- 2661-8036. ; 5:1, s. 189-197
-
Tidskriftsartikel (refereegranskat)abstract
- The effect of iron content on the type and distribution of carbides in the vacuum arc melted Fe-x(AlCoCrCuNiV)(88.05-x)Mo5W6-C-0.95 (x = 69, 76, 83 wt%, respectively) medium-entropy high-speed steels (ME-HSSs) was studied. The homogeneous distribution of granular MC carbides (M refers to the carbides forming transition metal elements, such as W, Mo and V), both at the grain boundary and in the martensitic matrix, was obtained in the Fe-76(AlCoCrCuNiV)(12.05)Mo5W6-C0.95ME-HSS, after quenching at 1210 degrees C followed by triple tempering at 530 degrees C. A maximum hardness of about 841 HV0.5 was achieved, even higher than the maximum hardness of the commercially available M2 (W6Mo5Cr4V2) HSS, 826 HV0.5. The medium-entropy effect was shown to be beneficial to transform the solidified primary carbide network into finely dispersed granular MC. However, when the iron content was further reduced to 69 wt%, the enhanced entropy effect promoted the dispersion of carbides but at the same time led to a decrease in the carbide content, so that the maximum hardness (816 HV0.5) was slightly lower than the maximum hardness of M2-HSS. The results provide a novel alloy system together with a simple heat treatment method to obtain hard HSSs, and more importantly to eliminate the primary carbide network which is harmful to the toughness of traditional HSS.
|
|
| 10. |
- Gačnik, Darja, et al.
(författare)
-
Structure and superconductivity of tin-containing hftizrsnm (M = cu, fe, nb, ni) medium-entropy and high-entropy alloys
- 2021
-
Ingår i: Materials. - : MDPI AG. - 1996-1944. ; 14:14
-
Tidskriftsartikel (refereegranskat)abstract
- In an attempt to incorporate tin (Sn) into high-entropy alloys composed of refractory metals Hf, Nb, Ti and Zr with the addition of 3d transition metals Cu, Fe, and Ni, we synthesized a series of alloys in the system HfTiZrSnM (M = Cu, Fe, Nb, Ni). The alloys were characterized crystallographically, microstructurally, and compositionally, and their physical properties were determined, with the emphasis on superconductivity. All Sn-containing alloys are multi-phase mixtures of intermetallic compounds (in most cases four). A common feature of the alloys is a microstructure of large crystalline grains of a hexagonal (Hf, Ti, Zr)5Sn3 partially ordered phase embedded in a matrix that also contains many small inclusions. In the HfTiZrSnCu alloy, some Cu is also incorporated into the grains. Based on the electrical resistivity, specific heat, and magnetization measurements, a superconducting (SC) state was observed in the HfTiZr, HfTiZrSn, HfTiZrSnNi, and HfTiZrSnNb alloys. The HfTiZrSnFe alloy shows a partial SC transition, whereas the HfTiZrSnCu alloy is non-superconducting. All SC alloys are type II superconductors and belong to the Anderson class of “dirty” superconductors.
|
|
