| 1. |
- Ganvir, Ashish, 1991-, et al.
(author)
-
Effect of suspension characteristics on the performance of thermal barrier coatings deposited by suspension plasma spray
- 2020
-
In: Ceramics International. - : Elsevier. - 0272-8842 .- 1873-3956. ; 47:1, s. 272-283
-
Journal article (peer-reviewed)abstract
- This paper investigates the influence of suspension characteristics on microstructure and performance of suspensions plasma sprayed (SPS) thermal barrier coatings (TBCs). Five suspensions were produced using various suspension characteristics, namely, type of solvent and solid load content, and the resultant suspensions were utilized to deposit five different TBCs under identical processing conditions. The produced TBCs were evaluated for their performance i.e. thermal conductivity, thermal cyclic fatigue (TCF) and thermal shock (TS) lifetime. This experimental study revealed that the differences in the microstructure of SPS TBCs produced using varied suspensions resulted in a wide-ranging overall TBC performance. All TBCs exhibited thermal conductivity lower than 1 W/(m. K) except water-ethanol mixed suspension produced TBC. The TS lifetime was also affected to a large extent where 10 wt % solid loaded ethanol and 25 wt % solid loaded water suspensions produced TBCs exhibited the highest and the lowest lifetime, respectively. On the contrary, TCF lifetime was not as significantly affected as thermal conductivity and TS lifetime, and all ethanol suspensions showed marginally better TCF lifetime than water and ethanol-water mixed suspensions deposited TBCs. © 2020
|
|
| 2. |
- Kumar, Nitish, 1995-, et al.
(author)
-
Columnar Thermal Barrier Coatings Produced by Different Thermal Spray Processes
- 2021
-
In: Journal of thermal spray technology (Print). - : Springer. - 1059-9630 .- 1544-1016. ; 30, s. 1437-1452
-
Journal article (peer-reviewed)abstract
- Suspension plasma spraying (SPS) and plasma spray-physical vapor deposition (PS-PVD) are the only thermal spray technologies shown to be capable of producing TBCs with columnar microstructures similar to the electron beam-physical vapor deposition (EB-PVD) process but at higher deposition rates and relatively lower costs. The objective of this study was to achieve fundamental understanding of the effect of different columnar microstructures produced by these two thermal spray processes on their insulation and lifetime performance and propose an optimized columnar microstructure. Characterization of TBCs in terms of microstructure, thermal conductivity, thermal cyclic fatigue lifetime and burner rig lifetime was performed. The results were compared with TBCs produced by the standard thermal spray technique, atmospheric plasma spraying (APS). Bondcoats deposited by the emerging high-velocity air fuel (HVAF) spraying were compared to the standard vacuum plasma-sprayed (VPS) bondcoats to investigate the influence of the bondcoat deposition process as well as topcoat-bondcoat interface topography. The results showed that the dense PS-PVD-processed TBC had the highest lifetime, although at an expense of the highest thermal conductivity. The reason for this behavior was attributed to the dense intracolumnar structure, wide intercolumnar gaps and high column density, thus improving the strain tolerance and fracture toughness.
|
|
| 3. |
- Aranke, Omkar, 1994-, et al.
(author)
-
Microstructural Evolution and Sintering of Suspension Plasma-Sprayed Columnar Thermal Barrier Coatings
- 2019
-
In: Journal of thermal spray technology (Print). - : Springer Science and Business Media LLC. - 1059-9630 .- 1544-1016. ; 28:1-2, s. 198-211
-
Journal article (peer-reviewed)abstract
- Suspension plasma spray (SPS) is capable of producing coatings with porous columnar structure, and it is also a much cheaper process compared to the conventionally used electron beam physical vapor deposition (EB-PVD). Although TBCs with a columnar microstructure that are fabricated using SPS have typically lower thermal conductivity than EB-PVD, they are used sparingly in the aerospace industry due to their lower fracture toughness and limited lifetime expectancy. Lifetime of TBCs is highly influenced by the topcoat microstructure. The objective of this work was to study the TBCs produced using axial SPS with different process parameters. Influence of the microstructure on lifetime of the coatings was of particular interest, and it was determined by thermal cyclic fatigue testing. The effect of sintering on microstructure of the coatings exposed to high temperatures was also investigated. Porosity measurements were taken using image analysis technique, and thermal conductivity of the coatings was determined by laser flash analysis. The results show that axial SPS is a promising method of producing TBCs having various microstructures with good lifetime. Changes in microstructure of topcoat due to sintering were seen evidently in porous coatings, whereas dense topcoats showed good resistance against sintering.
|
|
| 4. |
- Fefekos, Alexandros G., et al.
(author)
-
Effect of spray angle and substrate material on formation mechanisms and properties of HVAF sprayed coatings
- 2023
-
In: Surface & Coatings Technology. - : Elsevier. - 0257-8972 .- 1879-3347. ; 452
-
Journal article (peer-reviewed)abstract
- Thermally sprayed coatings are often used to enhance the surface properties (wear resistance, corrosion resistance, etc.) of engineering components in order to extend their performance and service lifetime. Typically, the industrial components to be coated possess complex geometries and are fabricated using different materials, which can influence the deposited coating’s microstructure and performance. High-velocity air fuel (HVAF) process is a relatively new thermal spray processing technique that has shown tremendous potential to deposit high performance coatings for durable industrial components. However, no detailed studies have been reported on HVAF sprayed coating formation mechanisms so far in relation to the spray angle and substrate properties, and the influence of coating material on the above. The objective of this work was to study the influence of spray angles and substrate materials on splat characteristics, coating microstructure evolution, properties and performance for two distinct coating materials. In this study, one cermet (WC-CoCr) and one metallic (Inconel 625) feedstock were deposited onto three different substrates (aluminium alloy, carbon steel and Hastelloy-X) utilising different spray angles (40°, 60° and 90°). The coating evolution was analysed utilising SEM/EDS, image analysis, and micro-indentation. To determine the tribological performance, coatings were subjected to dry sliding wear test utilising alumina ball as counter surface and specific wear rates were obtained. The results showed that initial splat characteristics were substantially altered on changing the substrate and the spray angle. However, the final coating properties were not affected significantly even though the deposition rate was reduced significantly at lower spray angle, suggesting the versatility of the HVAF process.
|
|
| 5. |
- Ganvir, Ashish, 1991-
(author)
-
Design of Suspension Plasma Sprayed Thermal Barrier Coatings
- 2018
-
Doctoral thesis (other academic/artistic)abstract
- Thermal barrier coatings (TBCs) are widely used on gas turbine components to provide thermal insulation, which in combination with advanced cooling, can enable the gas turbine to operate at significantly higher temperatures even above the melting temperature of the metallic components. There is a permanent need,mainly due to environmental reasons, to increase the combustion temperature inturbines, hence new TBC solutions are needed. By using a liquid feedstock in thermal spraying, new types of TBCs can be produced. Suspension plasma/flame or solution precursor plasma spraying are examples of techniques that can be utilized for liquid feedstock thermal spraying. This approach of using suspension and solution feedstock, which is an alternative to the conventional solid powder feedstock spraying, is gaining increasing research interest since it has been shown to be capable of producing coatings withsuperior performance. The objective of this research work was to identify relationships between process parameters, coating microstructure, thermal conductivity and lifetime in suspension plasma sprayed TBCs. A further objective was to utilize these relationships to enable tailoring of the TBC microstructure for superior performance compared to state-of-the-art TBC used in industry today, i.e. solid feedstock plasma sprayed TBCs. Different spraying techniques, namely suspension high velocity oxy fuel, solution precursor plasma and suspension plasma spraying (with axial and radial feeding) were explored and compared to solid feedstock plasma spraying. A variety of microstructures, such as highly porous, vertically cracked and columnar, were produced and investigated. It was shown that there are strong relationships between microstructure, thermo-mechanical properties and performance of the coatings. Specifically, axial suspension plasma spraying wasshown as a very promising technique to produce various microstructures as wellas highly durable coatings. Based on the experimental results, a tailored columnar microstructure design for a superior TBC performance is also proposed.
|
|
| 6. |
- Ganvir, Ashish, 1991-, et al.
(author)
-
Failure analysis of thermally cycled columnar thermal barrier coatings produced by high-velocity-air fuel and axial-suspension-plasma spraying : A design perspective
- 2018
-
In: Ceramics International. - : Elsevier BV. - 0272-8842 .- 1873-3956. ; 44:3, s. 3161-3172
-
Journal article (peer-reviewed)abstract
- Axial-suspension-plasma spraying (ASPS) is a fairly recent thermal spray technology which enables production of ceramic top coats in TBCs, incorporating simultaneously the properties of both the conventional-plasma sprayed (highly insulating porous structures) and electron-beam-physical-vapor-deposited (strain-tolerant columnar structures) top coats. TBCs are required to insulate the hot components in a gas turbine engine against high temperature and harsh operating conditions. Periodic heating and cooling of turbine engines during operation can create severe thermal cyclic fatigue conditions which can degrade the performance of these coatings eventually leading to the failure. An in-depth experimental investigation was performed to understand the failure behavior of columnar TBCs subjected to thermal cyclic fatigue (TCF) test at 1100 C. The study revealed that the TCF performance was influenced to an extent, by the top coat microstructure, but was primarily affected by the severity of thermally grown oxide (TGO) growth at the bond coat-top coat interface. Mixed failure modes comprising crack propagation through the bond coat-TGO interface, through TGO and within the top coat were identified. Based on the analysis of the experimental results and thorough discussion a novel design of microstructure for the high TCF performance columnar TBC is proposed. © 2017 Elsevier Ltd and Techna Group S.r.l.
|
|
| 7. |
|
|
| 8. |
- Ganvir, Ashish, 1991-, et al.
(author)
-
Thermal conductivity in suspension sprayed thermal barrier coatings : Modelling and experiments
- 2016
-
In: Proceedings of the International Thermal Spray Conference. - : ASM International. ; , s. 368-374
-
Conference paper (peer-reviewed)abstract
- Axial Suspension Plasma spraying (ASPS) can generate microstructures with higher porosity and pores in the size range from submicron to nanometre. ASPS Thermal Barrier Coatings (TBCs) have already shown a great potential to produce low thermal conductivity coatings for gas turbine applications. It is important to understand the fundamental relationship between microstructural defects in the coating such as grain boundaries, porosity etc. and thermal conductivity. Object Oriented Finite element analysis (OOF) has been shown to be an effective tool for evaluating thermal conductivity for conventional TBCs as this method is capable of incorporating the inherent microstructure as an input to the model. The objective of this work was to analyse the thermal conductivity of ASPS TBCs using experimental techniques and also to evaluate a procedure where OOF can be used to predict and analyse the thermal conductivity for these coatings. Verification of the model was done using experimental thermal conductivity. Results showed that the varied scaled porosity has a significant influence on the thermal conductivity. Smaller grains, higher overall porosity content and lower columnar density resulted in lower thermal conductivity. It was shown that OOF could be a powerful tool to predict and rank thermal conductivity of ASPS TBCs.
|
|
| 9. |
- Gupta, Mohit Kumar, 1986-, et al.
(author)
-
Bilayer Suspension Plasma-Sprayed Thermal Barrier Coatings with Enhanced Thermal Cyclic Lifetime : Experiments and Modeling
- 2017
-
In: Journal of thermal spray technology (Print). - : Springer Science and Business Media LLC. - 1059-9630 .- 1544-1016. ; 26:6, s. 1038-1051
-
Journal article (peer-reviewed)abstract
- Suspension plasma spraying (SPS) has been shown as a promising process to produce porous columnar strain tolerant coatings for thermal barrier coatings (TBCs) in gas turbine engines. However, the highly porous structure is vulnerable to crack propagation, especially near the topcoat-bondcoat interface where high stresses are generated due to thermal cycling. A topcoat layer with high toughness near the topcoat-bondcoat interface could be beneficial to enhance thermal cyclic lifetime of SPS TBCs. In this work, a bilayer coating system consisting of first a dense layer near the topcoat-bondcoat interface followed by a porous columnar layer was fabricated by SPS using Yttria-stabilised zirconia suspension. The objective of this work was to investigate if the bilayer topcoat architecture could enhance the thermal cyclic lifetime of SPS TBCs through experiments and to understand the effect of the column gaps/vertical cracks and the dense layer on the generated stresses in the TBC during thermal cyclic loading through finite element modeling. The experimental results show that the bilayer TBC had significantly higher lifetime than the single-layer TBC. The modeling results show that the dense layer and vertical cracks are beneficial as they reduce the thermally induced stresses which thus increase the lifetime.
|
|
| 10. |
- Gupta, Mohit Kumar, 1986-, et al.
(author)
-
Design of high lifetime suspension plasma sprayed thermal barrier coatings
- 2020
-
In: Journal of the European Ceramic Society. - : Elsevier BV. - 0955-2219 .- 1873-619X. ; 40:3, s. 768-779
-
Journal article (peer-reviewed)abstract
- Thermal barrier coatings (TBCs) fabricated by suspension plasma spraying (SPS) have shown improved performance due to their low thermal conductivity and high durability along with relatively low production cost. Improvements in SPS TBCs that could further enhance their lifetime would lead to their widespread industrialisation. The objective of this study was to design a SPS TBC system with optimised topcoat microstructure and topcoat bondcoat interface, combined with appropriate bondcoat microstructure and chemistry, which could exhibit high cyclic lifetime. Bondcoat deposition processes investigated in this study were high velocity air fuel (HVAF) spraying, high velocity oxy fuel spraying, vacuum plasma spraying, and diffusion process. Topcoat microstructure with high column density along with smooth topcoat bondcoat interface and oxidation resistant bondcoat was shown as a favourable design for significant improvements in the lifetime of SPS TBCs. HVAF sprayed bondcoat treated by shot peening and grit blasting was shown to create this favourable design.
|
|
