| 1. |
|
|
| 2. |
- Garcia, Danilo, 1973, et al.
(författare)
-
Validation of the 18-item Swedish Version of Ryff’s Psychological Well-Being Scales
- 2021
-
Ingår i: APS 2021 Virtual Convention.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- We found that the 18-item Swedish version of Ryff’s Psychological Well-Being Scales had the expected relationships with subjective well-being, lifestyle habits, and health issues. We also found that, although a six-factor solution had a good fit, a five-factor solution was the best fitting model for this specific version.
|
|
| 3. |
- Habibi, Maryam, et al.
(författare)
-
Corrosion resistance and surface microstructure of Mg 3 N 2 / SS thin films by plasma focus instrument
- 2022
-
Ingår i: Microscopy research and technique (Print). - : Wiley. - 1059-910X .- 1097-0029. ; 85:8, s. 2880-2893
-
Tidskriftsartikel (refereegranskat)abstract
- Utilizing a plasma focus (PF) instrument, magnesium nitride (Mg3 N2 ) thin films were synthesized on stainless steel substrates. Twenty five optimum focus shots at 8 cm distance from the anode tip were used to deposit the films at different angular positions regarded to the anode axis. Scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray diffraction (XRD) analyses were performed to assess the surface morphology and structural characteristics of Mg3 N2 films. Based on AFM images, these films were studied to understand the effect of angular position variation on their surfaces through morphological and fractal parameters. By increasing the angle, we verify that the grain size decreased from 130(0) nm to 75(5) nm and also the mean quadratic surface roughness of the films reduced in its average values from (28.97 ± 3.24) nm to (23.10 ± 1.34) nm. Power spectrum density analysis indicated that films become more self-affine at larger angles. Furthermore, the corrosion behavior of the films was investigated through a potentiodynamic polarization test in H2 SO4 solution. It was found that the ion energy and flux, varying with the angular positions from the anode tip, directly affected the nanostructured roughness and surface morphology of the samples. The electrochemical studies of films show that the uncoated sample presented the lowest corrosion resistance. The highest corrosion resistance was obtained for the sample deposited with 25 optimum shots and at 0° angular position reaching a reduction in the corrosion current density of almost 800 times compared to the pure stainless steel-304 substrate.
|
|
| 4. |
- Kazemitabar, Maryam, et al.
(författare)
-
School Health Assessment Tools: A Systematic Review of Measurement in Primary Schools
- 2020
-
Ingår i: PeerJ. - : PeerJ. - 2167-8359. ; 8, s. 1-21
-
Forskningsöversikt (refereegranskat)abstract
- Background: This systematic review aimed to investigate the psychometric properties of the school health’s assessment tools in primary schools through COSMIN Risk of Bias checklist. We examined the studies that have addressed the measurement properties of school-health instruments to give a clear overview of the quality of all available tools measuring school health in primary schools. This systematic review was registered in PROPERO with the Registration ID: CRD42020158158. Method: Databases of EBSCOhost, PubMed, ProQuest, Wily, PROSPERO, and OpenGrey were systematically searched without any time limitation to find all full-text English journal articles studied at least one of the COSMIN checklist measurement properties of a school-health assessment tool in primary schools. The instruments should be constructed based on a school health model. The eligible studies were assessed by COSMIN Risk of Bias checklist to report their quality of methodology for each measurement property and for the whole study by rating high, moderate or low quality. Results: At the final screening just seven studies remained for review. Four studies were tool development, three of them were rated as “adequate” and the other study as “very good”; five studies examined the content validity, three of them were appraised as “very good”, and the two remaining as “inadequate”. All seven studies measured structural validity, three of them were evaluated as “very good”, three other were scored as “adequate”, and the last study as “inadequate”. All the seven studies investigated the internal consistency, five of them were assessed as “very good”, one was rated as “doubtful”, and the last one as “inadequate”. Just one study examined the cross-cultural validity and was rated as “adequate”. Finally, all seven studies measured reliability, two of them were rated as “very good” and the rest five studies were appraised as “doubtful”. All rating was based on COSMIN checklist criteria for quality of measurement properties assessment. Conclusion: The number of studies addressing school health assessment tools was very low and therefore not sufficient. Hence, there is a serious need to investigate the psychometric properties of the available instruments measuring school health at primary schools. Moreover, the studies included in the present systematic review did not fulfill all the criteria of the COSMIN checklist for assessing measurement properties. We suggest that future studies consider these criteria for measuring psychometric properties and developing school health assessment tools.
|
|
| 5. |
- Safari, Maryam, et al.
(författare)
-
Effect of the structural features of biobased linear polyester plasticizers on the crystallization of polylactides
- 2022
-
Ingår i: International Journal of Biological Macromolecules. - : Elsevier BV. - 0141-8130 .- 1879-0003. ; 214, s. 128-139
-
Tidskriftsartikel (refereegranskat)abstract
- This work presents, for the first time, a detailed report on how the nucleation and crystallization of polylactide (PLLA) are affected by biobased aliphatic polyesters plasticizers. Three biobased polyesters were synthesized via solvent-free two-stage melt polycondensation of adipic acid (AdA) with three different biobased aliphatic diols and used as plasticizers for poly (L-lactic acid) (PLLA). The molecular structure of the synthesized polyesters was proved using 1H NMR, 13C NMR and Fourier transform infrared (FTIR) spectroscopy. PLLA/AdA-based blends containing 10 wt% of the polyester plasticizers were studied by tensile tests, dynamic mechanical analysis (DMA), wide-angle x-ray scattering (WAXS), differential scanning calorimetry (DSC) and polarized light optical microscopy (PLOM). Adding the plasticizers to PLLA decreased Tg by up to 11 °C and significantly increased the elongation at break by about 8 times compared with neat PLLA. The addition of 10 wt% of any AdA-based plasticizer to PLLA increases the nucleation rate from the glassy state by around 50-110 % depending on the plasticizer. The overall crystallization rate from the glassy state was 2-3 times faster for the plasticized PLLAs than neat PLLA. These results are a consequence of the lower energy barrier for both nucleation and growth processes. The incorporation of AdA-based linear polyesters had an incremental impact on the crystal growth rate (or secondary nucleation) of PLLA spherulites from the melt and glassy states. In conclusion, the AdA-based aliphatic polyesters allowed to enhance PLLA crystallization rates and showed interesting potential for the formulation of fully biobased PLLA blends.
|
|
