| 1. |
|
|
| 2. |
- Barkarmo, Sargon, et al.
(author)
-
Inflammatory cytokine release from human peripheral blood mononuclear cells exposed to polyetheretherketone and titanium-6 aluminum-4 vanadium in vitro.
- 2018
-
In: Journal of biomaterials applications. - : SAGE Publications. - 1530-8022 .- 0885-3282. ; 33:2, s. 245-258
-
Journal article (peer-reviewed)abstract
- Objective To investigate the cytokine expression profiles of blood cells exposed to polyetheretherketone and titanium-6 aluminum-4 vanadium materials in vitro. Materials and methods Coin-shaped samples composed of titanium-6 aluminum-4 vanadium, polyetheretherketone, and blasted polyetheretherketone were manufactured. The surfaces of the coins were characterized using optical interferometry, scanning electron microscopy, and contact angle measurements. Peripheral blood mononuclear cells collected from 10 blood donors were cultured for one, three, and six days in the presence or absence of the coins, and then assayed for cytokine production. Quantification of the peripheral blood mononuclear cells attached to the coins was performed using confocal microscopy after immunofluorescence staining. Results The machined titanium-6 aluminum-4 vanadium coins had a smoother surface topography compared to the machined polyetheretherketone and blasted polyetheretherketone. The highest mean contact angle was noted for the blasted polyetheretherketone, followed by the machined polyetheretherketone and titanium-6 aluminum-4 vanadium. The peripheral blood mononuclear cells produced significantly more proinflammatory cytokines when exposed to the polyetheretherketone surface compared to the titanium-6 aluminum-4 vanadium surface, while the blasted polyetheretherketone induced the highest level of proinflammatory cytokine release from the peripheral blood mononuclear cells. Significantly more cells attached to both polyetheretherketone surfaces, as compared to the titanium-6 aluminum-4 vanadium surface. Conclusion Polyetheretherketone induces a stronger inflammatory response from peripheral blood mononuclear cells than does titanium-6 aluminum-4 vanadium. Surface topography has an impact on cytokine release from peripheral blood mononuclear cells.
|
|
| 3. |
- Bolind, Pia, 1953, et al.
(author)
-
Histologic evaluation of Branemark clinic oral implants retrieved from grafted sites
- 2006
-
In: Clinical implant dentistry and related research. - Hamilton, Ont. : Wiley. - 1523-0899 .- 1708-8208. ; 8:1, s. 44-53
-
Journal article (peer-reviewed)abstract
- PURPOSE: The aim of this report is to quantitatively and qualitatively describe the bone tissue response to Branemark implants retrieved from grafted sites in patients. MATERIALS AND METHOD: The material consists of consecutively received Branemark implants retrieved from grafted sites. Thirty-five of these implants, retrieved from 16 patients, were suitable for the histologic evaluation of undecalcified sections in the light microscope. RESULTS: The unloaded implants were mainly lined with soft tissue, and sparse bone-implant contact was observed only in some sections. The loaded implants, with the exception of one implant removed due to mobility, had mature and new bone-implant contact. Resorption of graft through cutting cone structures was detected. Cement lines were found separating bone-like tissue albeit no cellular content and bone tissue with detectable osteocytes. CONCLUSION: In this heterogeneous group of implants from grafted sites, the unloaded implants showed limited bone-implant contact. The autografts showed seemingly mixed viability as judged by the cell content in the osteocyte lacunae and cement lines separating areas with filled and empty lacunae.
|
|
| 4. |
- Bolind, Pia, 1953, et al.
(author)
-
Retrieved implants from irradiated sites in humans: a histologic/histomorphometric investigation of oral and craniofacial implants
- 2006
-
In: Clinical implant dentistry and related research. - Hamilton, Ont. : Wiley. - 1523-0899 .- 1708-8208. ; 8:3, s. 142-50
-
Journal article (peer-reviewed)abstract
- PURPOSE: The aim of this report was to quantitatively and qualitatively evaluate the tissue response to bone-anchored implants retrieved from irradiated sites in patients. MATERIALS AND METHODS: The material consists of 23 consecutively received Branemark implants (Nobel Biocare AB, Goteborg, Sweden) placed in pre- or postoperatively irradiated sites. Twenty-two of the 23 implants were suitable for histologic evaluation of undecalcified sections in the light microscope. RESULTS: The oral implants with shorter time in situ demonstrated sparse bone to implant contact with mainly dense connective tissue in the interface. However, for implants with longer time in situ, high amounts of bone-implant contact and bone fill of threads were noted. The mean values of bone-implant contact and bone area within the thread were calculated to 40% (16-94) and 70% (13-96), respectively. The craniofacial implants, with the exception of two implants lined with a capsular formation, demonstrated mature and newly formed bone at the bone-implant interface. The mean value for bone-metal contact was calculated to 45 and 53% for two specimens. The mean value for bone area within the thread ranged from 65 to 88% for three specimens. CONCLUSION; The possibility to achieve bone anchorage of implants in irradiated tissue was supported by the findings in this study. However, due to limited material, conclusions with regard to radiation dose and bone tissue response to implants cannot be stated.
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Kassapidou, Maria, et al.
(author)
-
Cobalt-chromium alloys fabricated with four different techniques: Ion release, toxicity of released elements and surface roughness
- 2020
-
In: Dental Materials. - : Elsevier BV. - 0109-5641 .- 1879-0097. ; 36:11
-
Journal article (peer-reviewed)abstract
- Objective. To investigate the metal ion release, surface roughness and cytoxicity for Co-Cr alloys produced by different manufacturing techniques before and after heat treatment. In addition, to evaluate if the combination of materials affects the ion release. Methods. Five Co-Cr alloys were included, based on four manufacturing techniques. Commercially pure titanium, CpTi grade 4 and a titanium alloy were included for comparison. The ion release tests involved both Inductive Coupled Plasma Optical Emission Spectrometry and Inductive Coupled Plasma Mass Spectrometry analyses. The surface analysis was conducted with optical interferometry. Cells were indirectly exposed to the materials and cell viability was evaluated with the MTT (3-(4.5-dimethylthiazol-2-yl)-2.5-diphenyltetrazolium bromide) method. Results. All alloys showed a decrease of the total ion release when CpTi grade 4 was present. The total ion release decreased over time for all specimens and the highest ion release was observed from the cast and milled Co-Cr alloy in acidic conditions. The cast and laser-melted Co-Cr alloy and the titanium alloy became rougher after heat treatment. All materials were within the limits of cell viability according to standards. Significance. The ion release from Co-Cr alloys is influenced by the combination of materials, pH and time. Surface roughness is influenced by heat treatment. Furthermore, both ion release and surface roughness are influenced by the manufacturing technique and the alloy type. The clinical implication needs to be further investigated. (C) 2020 The Academy of Dental Materials. Published by Elsevier Inc.
|
|
| 9. |
- Kassapidou, Maria, et al.
(author)
-
Cobalt-chromium alloys in fixed prosthodontics : Investigations of mechanical properties and microstructure
- 2023
-
In: The Journal of prosthetic dentistry (Print). - : Elsevier. - 0022-3913 .- 1097-6841. ; 130:2, s. 255.e1-255.e10
-
Journal article (peer-reviewed)abstract
- STATEMENT OF PROBLEM: Cobalt-chromium (Co-Cr) alloys possess beneficial mechanical properties because alloys, even in thin sections, can resist high mastication forces and exhibit an acceptable bond to the surface porcelain layer. Traditional manufacturing techniques of Co-Cr alloys such as casting have been replaced with newer fabrication techniques, such as milling, laser melting, and presintered milling. Despite scarce documentation, these new manufacturing techniques are being used to fabricate dental and implant constructions.PURPOSE: This in vitro study investigates the hardness, yield strength, elastic modulus, and microstructure of the most commonly used Co-Cr alloys for fixed prosthodontics based on manufacturing technique. In addition, this study investigates the effect of heat treatment on the mechanical properties and microstructure of these materials.MATERIAL AND METHODS: Five Co-Cr alloys were included (dumbbell and rectangular shaped) based on four manufacturing techniques: cast, milled, laser melted, and presintered milled. Commercially pure titanium grade 4 and titanium-6 aluminum-4 vanadium ELI (extra low interstitial) were included for comparison, and yield strength and elongation after fracture were evaluated. The specimens were tested for hardness using the Vickers test and for elastic modulus using a nondestructive impulse excitation technique. The microstructure of selected specimens was analyzed using focused ion beam-scanning electron microscopy (FIB-SEM) and energy dispersive X-ray spectroscopy (EDS).RESULTS: The mechanical properties depend on the manufacturing technique used; the laser-melted and presintered Co-Cr specimens demonstrated the highest mechanical properties, followed by the milled and cast groups. Both the laser-melted and the presintered milled Co-Cr specimens showed smaller grain size compared with the cast and milled Co-Cr specimens. The titanium-6 aluminum-4 vanadium ELI demonstrated higher hardness and yield strength compared to commercially pure titanium grade 4. No major differences were observed for the selected materials regarding the mechanical properties and microstructural appearance after heat treatment.CONCLUSIONS: The laser melting and presintered milling techniques produced higher mechanical properties compared with the cast and milled Co-Cr. These findings were confirmed through microstructural analysis with respect to the grain size, precipitation, and number of pores.
|
|
| 10. |
- Kassapidou, Maria, et al.
(author)
-
Inflammatory Response to Cobalt-Chromium Alloys Fabricated With Different Techniques
- 2021
-
In: Journal of Oral & Maxillofacial Research. - : UAB Stilus Optimus. - 2029-283X. ; 12:4
-
Journal article (peer-reviewed)abstract
- Objectives: To explore the in vitro cytokine expression of human peripheral blood mononuclear cells exposed to cobalt-chromium alloys, manufactured with different techniques, in comparison with commercially pure titanium grade 4 and titanium alloy grade 23.Material and Methods: Peripheral blood mononuclear cells (PBMC) were collected from 10 healthy blood donors and exposed to machine-ground coin-shaped: (a) cobalt-chromium (Co-Cr) specimens (n = 5) manufactured by four techniques, i.e. cast, milled, laser melted and presintered milled; (b) commercially pure titanium grade 4; and (c) titanium alloy grade 23. The cells were cultured for 4, 24 and 72 hours followed by investigations of pro- and anti-inflammatory cytokine release using Bio-Plex Pro (TM).Results: In general, the PBMC produced significantly more cytokines when exposed to the cast and presintered milled Co-Cr materials compared to laser melted, milled Co-Cr and titanium materials.Conclusions: Within the limitation of the present study, it may be suggested that cast and presintered milled cobalt-chromium alloys provoke a stronger inflammatory response compared to milled and laser melted cobalt-chromium alloys and titanium materials.
|
|
