1. |
- Abom, A.E., et al.
(författare)
-
Characterization of the metal-insulator interface of field-effect chemical sensors
- 2003
-
Ingår i: Journal of Applied Physics. - : AIP Publishing. - 0021-8979 .- 1089-7550. ; 93:12, s. 9760-9768
-
Tidskriftsartikel (refereegranskat)abstract
- The metal-insulator interface of hydrogen-sensitive metal-insulator-semiconductor capacitors, with SiO2 as the insulator and Pt as the metal contact, was discussed. It was found that the difference in hydrogen response between differently prepared devices was explained by a difference in concentration of available adsorption sites. The analysis showed that the concentration of Pt atoms in contact with the oxide affected both the hydrogen response and the metal-oxide adhesion.
|
|
2. |
- Bendsen, Nathalie T., et al.
(författare)
-
Effect of industrially produced trans fat on markers of systemic inflammation : evidence from a randomized trial in women
- 2011
-
Ingår i: Journal of Lipid Research. - 0022-2275 .- 1539-7262. ; 52:10, s. 1821-1828
-
Tidskriftsartikel (refereegranskat)abstract
- Consumption of industrially produced trans fatty acids (IP-TFA) has been positively associated with systemic markers of low-grade inflammation and endothelial dysfunction in cross-sectional studies, but results from intervention studies are inconclusive. Therefore, we conducted a 16 week double-blind parallel intervention study with the objective to examine the effect of IP-TFA intake on bio-markers of inflammation, oxidative stress, and endothelial dysfunction. Fifty-two healthy overweight postmenopausal women (49 completers) were randomly assigned to receive either partially hydrogenated soybean oil (15.7 g/day IP-TFA) or control oil without IP-TFA. After 16 weeks, IP-TFA intake increased baseline-adjusted serum tumor necrosis factor (TNF) alpha by 12% [95% confidence interval (CI): 5-20; P = 0.002] more in the IP-TFA group compared with controls. Plasma soluble TNF receptors 1 and 2 were also increased by IP-TFA [155 pg/ml (CI: 63-247); P < 0.001 and 480 pg/ml (CI: 72-887); P = 0.02, respectively]. Serum C-reactive protein, interleukin (IL) 6 and adiponectin and subcutaneous abdominal adipose tissue mRNA expression of IL6, IL8, TNF alpha, and adiponectin as well as ceramide content were not affected by IP-TFA, nor was urinary 8-iso-prostaglandin-F(2 alpha). In conclusion, this dietary trial indicates that the mechanisms linking dietary IP-TFA to cardiovascular disease may involve activation of the TNF alpha system.
|
|
3. |
- Bengtsson, Caroline, et al.
(författare)
-
Incident chronic rhinosinusitis is associated with impaired sleep quality: Results of the RhiNE study
- 2019
-
Ingår i: Journal of Clinical Sleep Medicine. - : American Academy of Sleep Medicine (AASM). - 1550-9389 .- 1550-9397. ; 15:6, s. 899-905
-
Tidskriftsartikel (refereegranskat)abstract
- Study Objectives: Chronic rhinosinusitis (CRS) is a common inflammatory disease of the nasal cavity and paranasal sinuses. Associations between CRS and poor sleep quality have been reported. This 10-year follow-up study investigates possible associations between incident CRS and sleep quality. Methods: A questionnaire was sent to 16,500 individuals in Sweden, Norway, Denmark, Iceland and Estonia in 2000. It included questions on airway diseases, age, sex, body mass index, smoking habits, comorbidities, education and sleep quality. In 2010, a second questionnaire was sent to the same individuals, with a response rate of 53%. A subgroup of 5,145 individuals without nasal symptoms in 2000 was studied. Multiple logistic regression was performed to examine associations between CRS (defined according to the European position paper on rhinosinusitis and nasal polyps epidemiological criteria) at follow-up and sleep quality, with adjustment for potential confounders. Individuals with the respective sleep problem at baseline were excluded. Results: Over 10 years, 141 (2.7%) of the individuals without nasal symptoms in 2000 had developed CRS. CRS was associated with difficulties inducing sleep (adjusted odds ratio 2.81 [95% CI 1.67–4.70]), difficulties maintaining sleep (2.07 [1.35–3.18]), early morning awakening (3.03 [1.91–4.81]), insomnia (2.21 [1.46–3.35]), excessive daytime sleepiness (2.85 [1.79–4.55]), and snoring (3.31 [2.07–5.31]). Three insomnia symptoms at baseline increased the risk of CRS at follow-up by 5.00 (1.93–12.99). Conclusions: Incident CRS is associated with impaired sleep quality and excessive daytime sleepiness. Insomnia symptoms may be a risk factor for the development of CRS. © 2019 American Academy of Sleep Medicine. All rights reserved.
|
|
4. |
|
|
5. |
|
|
6. |
- Berlind, Torun, 1965-, et al.
(författare)
-
Microstructure, mechanical properties, and wetting behaviorof Si-C-N thin films grown by reactive magnetron sputtering
- 2001
-
Ingår i: Surface and Coatings Technology. - : Elsevier. - 0257-8972. ; 141:2-3, s. 145-155
-
Tidskriftsartikel (refereegranskat)abstract
- Silicon–carbon–nitride (Si–C–N) thin films were deposited by reactive magnetron co-sputtering of C and Si targets in a mixed Ar/N2 discharge. Films were grown to a thickness of more than 0.5 μm on graphite and Si(001) substrates held at a negative floating potential of −35 V, and substrate temperature between 100 and 700°C. The total pressure was constant at 0.4 Pa (3 mtorr), and the nitrogen fraction in the gas mixture was varied between 0 and 100%. As-deposited films were analyzed with respect to composition, state of chemical bonding, microstructure, mechanical properties, and wetting behavior by Rutherford backscattering spectroscopy (RBS), energy dispersive spectroscopy (EDS), X-ray photoelectron spectrometry (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), nanoindentation and contact angle measurements, respectively. Depending on the deposition condition, ternary SixCyNz films within the composition range 1≤x≤34 at.%, 34≤y≤81 at.%, and 16.5≤z≤42 at.% were prepared with a textured, amorphous-to-graphite-like microstructure. For Si–C–N films with low Si content, C---C, C---N and Si---C bonds were present. At higher Si content, N preferentially bonds to Si, while less C---N bonds were observed. Films containing more than 12 at.% of Si contained widely dispersed crystallites, 2–20 nm in diameter. Incorporation of a few at.% Si resulted in a dramatic reduction of the film surface energy compared to pure CN films. The measured contact angles using distilled water and glycerol liquids were for some films comparable with those on a polytetrafluoroethylene (PTFE), Teflon® surface. The hardness of Si–C–N films could be varied over the range 9–28 GPa.
|
|
7. |
- Braun, Oscar Ö., et al.
(författare)
-
Continuous-flow LVADs in the Nordic countries : complications and mortality and its predictors
- 2019
-
Ingår i: Scandinavian Cardiovascular Journal. - : Informa UK Limited. - 1401-7431 .- 1651-2006. ; 53:1, s. 14-20
-
Tidskriftsartikel (refereegranskat)abstract
- Objectives: The purpose of this study was to assess complications and mortality and its predictors, with continuous-flow left ventricular assist devices (CF-LVADs) in the Nordic Countries.Design: This was a retrospective, international, multicenter cohort study.Results: Between 1993 and 2013, 442 surgically implanted long-term mechanical assist devices were used among 8 centers in the Nordic countries. Of those, 238 were CF-LVADs (HVAD or HeartMate II) implanted in patients >18 years with complete data. Postoperative complications and survival were compared and Cox proportion hazard regression analysis was used to identify predictors of mortality. The overall Kaplan-Meier survival rate was 75% at 1 year, 69% at 2 years and 63% at 3 years. A planned strategy of destination therapy had poorer survival compared to a strategy of bridge to transplantation or decision (2-year survival of 41% vs. 76%, p < .001). The most common complications were non-driveline infections (excluding sepsis) (44%), driveline infection (27%), need for continuous renal replacement therapy (25%) and right heart failure (24%). In a multivariate model age and left ventricular diastolic dimension was left as independent risk factors for mortality with a hazard ratio of 1.35 (95% confidence interval (CI) [1.01-1.80], p = .046) per 10 years and 0.88 (95% CI [0.72-0.99], p = .044) per 5 mm, respectively.Conclusion: Outcome with CF LVAD in the Nordic countries was comparable to other cohorts. Higher age and destination therapy require particularly stringent selection.
|
|
8. |
- Broitman, E., et al.
(författare)
-
Carbon nitride films on orthopedic substrates
- 2000
-
Ingår i: Diamond and related materials. - 0925-9635 .- 1879-0062. ; 9:12, s. 1984-1991
-
Tidskriftsartikel (refereegranskat)abstract
- The mechanical and tribological properties of carbon nitride (CN(X)) films deposited on orthopedic substrates are presented. CN(X) films were prepared by d.c. reactive magnetron sputtering from a graphite target in N2/Ar plasma. Films were grown on Ni and ZrO2 substrates to a thickness of ~1 µm at a total pressure of 3 mtorr and a substrate temperature of 250°C. High-resolution transmission electron microscopy (HRTEM) shows dense and homogeneous films, with 'fullerene-like' micro-structures consisting of curved, frequently intersecting, and highly in-plane oriented basal lattice planes. Nanoindentation measurements revealed a change in the mechanical properties of films treated with three different biological solutions. Spectroscopic analysis confirmed a change in the chemical structure of the treated films. The friction coefficients of CN(X) films against high speed steel (HSS), ZrO2 and Ultra-High Molecular Weight Polyethylene (UHMWPE) balls were evaluated by ball-on-disk tests in dry and lubricated conditions. In the case of dry sliding against a HSS ball, the steady state friction coefficient values are 0.22 for the film on the Ti substrate and 0.26 for the film on the ZrO2 substrate. The friction coefficients under human serum lubrication conditions were below 0.18 for the ZrO2 and UHMWPE balls. An increase in wettability of human plasma on CN(X) films was observed compared to the orthopedic surfaces, which could enhance the retention of synovial fluid on those surfaces, improving the lubrication of the bearings of total joint arthroplasty components during function. (C) 2000 Elsevier Science B.V. All rights reserved.The mechanical and tribological properties of carbon nitride (CNX) films deposited on orthopedic substrates are presented. CNX films were prepared by d.c. reactive magnetron sputtering from a graphite target in N2/Ar plasma. Films were grown on Ni and ZrO2 substrates to a thickness of approximately 1 µm at a total pressure of 3 mtorr and a substrate temperature of 250 °C. High-resolution transmission electron microscopy (HRTEM) shows dense and homogeneous films, with `fullerene-like' microstructures consisting of curved, frequently intersecting, and highly in-plane oriented basal lattice planes. Nanoindentation measurements revealed a change in the mechanical properties of films treated with three different biological solutions. Spectroscopic analysis confirmed a change in the chemical structure of the treated films. The friction coefficients of CNX films against high speed steel (HSS), ZrO2 and Ultra-High Molecular Weight Polyethylene (UHMWPE) balls were evaluated by ball-on-disk tests in dry and lubricated conditions. In the case of dry sliding against a HSS ball, the steady state friction coefficient values are 0.22 for the film on the Ti substrate and 0.26 for the film on the ZrO2 substrate. The friction coefficients under human serum lubrication conditions were below 0.18 for the ZrO2 and UHMWPE balls. An increase in wettability of human plasma on CNX films was observed compared to the orthopedic surfaces, which could enhance the retention of synovial fluid on those surfaces, improving the lubrication of the bearings of total joint arthroplasty components during function.
|
|
9. |
- Broitman, E., et al.
(författare)
-
Electrical and optical properties of CNx(0=x=0.25) films deposited by reactive magnetron sputtering
- 2001
-
Ingår i: Journal of Applied Physics. - : AIP Publishing. - 0021-8979 .- 1089-7550. ; 89:2, s. 1184-1190
-
Tidskriftsartikel (refereegranskat)abstract
- The electrical and optical properties of carbon-nitride CNx films (O=x=0.25) deposited by unbalanced reactive magnetron sputtering from a graphite target in mixed Ar/N2 discharges at a substrate temperature of 350°C have been investigated. Pure C films exhibit a dark conductivity at room temperature of 250 O-1 cm-1, which grows up to 250 O-1 cm-1 for CNx films with N content of 20%. For CNx films, temperature-dependent conductivity measurements suggest that two electron conduction processes exist in the investigated temperature range 130
|
|
10. |
- Broitman, E, et al.
(författare)
-
Letter: Electrical properties of carbon nitride thin films : Role of morphology and hydrogen content
- 2002
-
Ingår i: Journal of Electronic Materials. - 0361-5235 .- 1543-186X. ; 31:9, s. 957-961
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)abstract
- The influence of hydrogen content and ambient humidity on the electrical properties of carbon nitride (CNX) films deposited by reactive magnetron sputtering from a graphite target in Ar discharges mixed with N-2 and H-2 at a substrate temperature of 350degreesC have been investigated. Carbon films deposited in pure Ar exhibit a dark resistivity at room temperature of similar to4 X 10(-2) Omegacm, while the resistivity is one order of magnitude lower for CN0.25 films deposited in pure N-2, due to their denser morphology. The increasing H-2 fraction in the discharge gas leads to an increased resistivity for all gas mixtures. This is most pronounced for the nitrogen-free films deposited in an Ar/H-2 mixture, where the resistivity increases by over four orders of magnitude. This can be related to a decreased electron mobility as H inhibits the formation of double bonds. After exposure to air, the resistivity increases with time through two different diffusion regimes. The measured electrical properties of the films are related to the apparent film microstructure, bonding nature, and ambient humidity.
|
|