| 1. |
- Sedighi Moghaddam, Maziar, et al.
(författare)
-
Hydrophobisation of wood surfaces by combining liquid flame spray (LFS) and plasma treatment : Dynamic wetting properties
- 2016
-
Ingår i: Holzforschung. - : Walter de Gruyter. - 0018-3830 .- 1437-434X. ; 70:6, s. 527-537
-
Tidskriftsartikel (refereegranskat)abstract
- The hydrophilic nature of wood surfaces is a major cause for water uptake and subsequent biological degradation and dimensional changes. In the present paper, a thin transparent superhydrophobic layer on pine veneer surfaces has been created for controlling surface wettability and water repellency. This effect was achieved by means of the liquid flame spray (LFS) technique, in the course of which the nanoparticulate titanium dioxide (TiO2) was brought to the surface, followed by plasma polymerisation. Plasma polymerised perfluorohexane (PFH) or hexamethyldisiloxane (HMDSO) were then deposited onto the LFS-treated wood surfaces. The same treatment systems were applied to silicon wafers so as to have well-defined reference surfaces. The dynamic wettability was studied by the multicycle Wilhelmy plate (mWP) method, resulting in advancing and receding contact angles as well as sorption behavior of the samples during repeated wetting cycles in water. Atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were employed to characterise the topography and surface chemical compositions and to elucidate the question how the morphology of the nanoparticles and plasma affect the wetting behavior. A multi-scale roughness (micro-nano roughness) was found and this enhanced the forced wetting durability via a superhydrophobic effect on the surface, which was stable even after repeated wetting cycles. The hydrophobic effect of this approach was higher compared to that of plasma modified surfaces with their micro-scale modification.
|
|
| 2. |
|
|
| 3. |
- Heydari, Golrokh, et al.
(författare)
-
Hydrophobic Surfaces : Topography Effects on Wetting by Supercooled Water and Freezing Delay
- 2013
-
Ingår i: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 117:42, s. 21752-21762
-
Tidskriftsartikel (refereegranskat)abstract
- Hydrophobicity, and in particular superhydrophobicity, has been extensively considered to promote ice-phobicity. Dynamic contact angle measurements above 0 degrees C have been widely used to evaluate the water repellency. However, it is the wetting properties of supercooled water at subzero temperatures and the derived work of adhesion that are important for applications dealing with icing. In this work we address this issue by determining the temperature-dependent dynamic contact angle of microliter-sized water droplets on a smooth hydrophobic and a superhydrophobic surface with similar surface chemistry. The data highlight how the work of adhesion of water in the temperature interval from about 25 degrees C to below -10 degrees C is affected by surface topography. A marked decrease in contact angle on the superhydrophobic surface is observed with decreasing temperature, and we attribute this to condensation below the dew point. In contrast, no significant wetting transition is observed on the smooth hydrophobic surface. The freezing temperature and the freezing delay time were determined for water droplets resting on a range of surfaces with similar chemistry but different topography, including smooth and rough surfaces in either the Wenzel or the Cassie-Baxter state as characterized by water contact angle measurements at room temperature. We find that the water freezing delay time is not significantly affected by the surface topography and discuss this finding within the classical theory of heterogeneous nucleation.
|
|
| 4. |
- Heydari, Golrokh, 1982-, et al.
(författare)
-
Temperature-Dependent Deicing Properties of ElectrostaticallyAnchored Branched Brush Layers of Poly(ethylene oxide)
- 2016
-
Ingår i: Langmuir. - : American Chemical Society (ACS). - 0743-7463 .- 1520-5827. ; 32:17, s. 4194-4202
-
Tidskriftsartikel (refereegranskat)abstract
- The hydration water of hydrophilic polymersfreezes at subzero temperatures. The adsorption of suchpolymers will result in a hydrophilic surface layer that stronglybinds water. Provided this interfacial hydration water remainsliquidlike at subzero temperatures, its presence could possiblyreduce ice adhesion, in particular, if the liquidlike layer isthicker than or comparable to the surface roughness. Toexplore this idea, a diblock copolymer, having one branchedbottle-brush block of poly(ethylene oxide) and one linear cationic block, was electrostatically anchored on flat silica surfaces. Theshear ice adhesion strength on such polymer-coated surfaces was investigated down to −25 °C using a homebuilt device. Inaddition, the temperature dependence of the ice adhesion on surfaces coated with only the cationic block, only the branchedbottle-brush block, and with linear poly(ethylene oxide) was investigated. Significant ice adhesion reduction, in particular, attemperatures above −15 °C, was observed on silica surfaces coated with the electrostatically anchored diblock copolymer.Differential scanning calorimetry measurements on bulk polymer solutions demonstrate different thermal transitions of waterinteracting with branched and linear poly(ethylene oxide) (with hydration water melting points of about −18 and −10 °C,respectively). This difference is consistent with the low shear ice adhesion strength measured on surfaces carrying branchedbottle-brush structured poly(ethylene oxide) at −10 °C, whereas no significant adhesion reduction was obtained with linearpoly(ethylene oxide) at this temperature. We propose a lubrication effect of the hydration water bound to the branched bottlebrushstructured poly(ethylene oxide), which, in the bulk, does not freeze until −18 °C.
|
|
| 5. |
- Heydari, Golrokh, 1982-
(författare)
-
Toward Anti-icing and De-icing Surfaces : Effects of Surface Topography and Temperature
- 2016
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Icing severely affects society, especially in the Nordic countries. Iceaccumulation can result in critical performance problems and safetyconcerns for instance in road, air and sea transportation, transmissionlines, marine and offshore structures, wind turbines and heat exchangers.Present active ice-combating approaches possess environmental,efficiency and cost drawbacks. Thus, fabricating icephobic surfaces orcoatings impeding ice formation (anti-icing), but facilitating ice removal(de-icing) is desired. However, different conditions in the environmentduring ice formation and growth add to the complexity of the problem.An icephobic surface that works for a certain application might not be agood candidate for another. These surfaces and the challenges are infocus in this thesis.Wetting properties are important for ice formation on surfaces fromthe liquid phase (often supercooled water), where the water repellency ofthe surfaces could enhance their anti-icing effect. Considering this,different hydrophobic and superhydrophobic surfaces with differentchemistry, morphology and roughness scale were prepared. Since anyinduced wetting state hysteresis on hydrophobic surfaces could influencetheir performance, the wetting stability was investigated. In particulardynamic wetting studies of the hydrophobic surfaces revealed whatsurface characteristics benefit a stable wetting performance. Further, theeffect of temperature, particularly sub-zero temperatures, on the wettingstate of flat and nanostructured hydrophobic surfaces was investigated.This was complemented with studies of the wetting stability of sessilewater droplets on flat to micro- and multi-scale (micro-nano) roughhydrophobic samples in a freeze-thaw cycle. To be consistent with mostapplications, all temperature-controlled experiments were performed inan environmental condition facilitating frost formation. Further, antiicingproperties of hydrophobic surfaces with different topography butsimilar chemistry were studied by freezing delay measurements.A dynamic wetting study using hydrophobic samples with similarchemistry but different topography revealed that multi-scale roughnesscould benefit the wetting stability. However, when these surfaces areutilized at low temperatures the wetting hysteresis observed during acooling/heating cycle is significant. Such a temperature-inducedhysteresis is also significant on superhydrophobic surfaces. I attributethis to condensation followed by frost formation facilitating spreading of the supercooled water droplet. The freezing delay measurementsdemonstrate no significant effect of surface topography on anti-icingproperties of hydrophobic surfaces, however the flat surfaces showed thelongest delay. These findings are in agreement with heterogeneous icenucleation theory, suggesting preferential ice nucleation in concave sites,provided they are wetted.In the second part of this thesis, I consider the findings from theprevious part illustrating the limitations of (super)hydrophobic surfaces.The de-icing properties of hydrophilic surfaces with a hydration waterlayer, hypothesized to lubricate the interface with ice, were studied. Heretemperature-controlled shear ice adhesion measurements, down to -25oC, were performed on an adsorbed layer of a polymer, either bottle-brushstructured poly(ethylene oxide) or linear poly(ethylene oxide). The iceadhesion strength was reduced significantly on the bottle-brushstructured polymer layer, specifically at temperatures above -15 oC,whereas less adhesion reduction was observed on the layer formed by thelinear polymer. These findings are consistent with differential scanningcalorimetry (DSC) data, demonstrating that the hydration water, boundto the bottle-brush structured polymer, is in the liquid state at thetemperatures where de-icing benefit is observed. Further, continuingwith the hypothesis of the advantage of surfaces with a natural lubricantlayer for de-icing targets, I studied shear ice adhesion on the molecularlyflat basal plane of hydrophilic mica down to -35 oC. Interestingly, ultralowice adhesion strength was measured on this surface. I relate this to theproposed distinct structure of the first ice-like but fluid water layer onmica, with no free OH groups, followed by more bulk liquid-like layers.This combined with the molecularly smooth nature of mica results in aperfect plane for ice sliding.
|
|
| 6. |
- Heydari, Golrokh, 1982-, et al.
(författare)
-
Ultralow ice adhesion on hydrophilic and molecularly smooth mica surfaces
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- Despite much research on designing surfaces for combating icing, no permanent solution has been achievedusing solid materials. Inspired by the slippery surface of ice, attributed to the presence of a quasi-liquid layeracting as a natural lubricant, we hypothesize that flat hydrophilic surfaces with a hydration layer remaining inthe liquid-like state at the solid-ice interface could result in low ice adhesion. Utilizing temperature-controlledice adhesion measurements on the molecularly smooth basal plane of muscovite mica, we observed the lowestreported ice adhesion on solid surfaces down to temperatures of -35 ºC. The ice adhesion is dramatically higheron flat hydrophilic silica surfaces. We discuss these findings in terms of what is known about mica-water andmica-ice interactions.
|
|
| 7. |
- Heydari, Golrokh, et al.
(författare)
-
Wetting hysteresis induced by temperature changes : supercooled water onhydrophobic surfaces
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- The state and stability of supercooled water on (super)hydrophobic surfaces is crucial for low temperature applications and for obtaining anti-icing and de-icing properties. Surface characteristics such as topography and chemistry are expected to affect wetting hysteresis during temperature cycling experiments, and also the freezing delay of supercooled water. We utilized stochastically rough wood surfaces that were further modified to render them hydrophobic or superhydrophobic. Liquid flame spraying (LFS) was utilized to create a multi-scale roughness by depositing titaniumdioxide nanoparticles. The coating was subsequently made non-polar by applying a thin plasma polymer layer. As flat reference samples modified silica surfaces with similar chemistries were utilized. With these sets of surfaces we test the hypothesis that superhydrophobic surfaces also should retard ice formation. Wetting hysteresis was evaluated using contact angle measurements during a freeze-thaw cycle from room temperature to freezing occurrence at -7 °C, and then back to room temperature. Further, the delay in freezing of supercooled water droplets was studied at temperatures of -4 °C and -7 °C. The hysteresis in contact angle observed during a cooling-heating cycle is found to be small on flat hydrophobic surfaces. However, significant changes in contact angles during a cooling-heating cycle are observed on the rough surfaces, with a higher contact angle observed on cooling compared to during the subsequent heating. This hysteresis is lower for hydrophobic wood samples with multi-scale roughness compared to those with predominantly micro-scale features. Condensation and subsequent frost formation at sub-zero temperatures induce the hysteresis. The freezing delay data suggests that the multi-scale roughness reduces the penetration of supercooled water into surface depressions, and enhances the freezing delay at low degrees of supercooling. However, the flat surface is even more efficient in enhancing the freezing delay than the rougher surfaces, which can be rationalized considering heterogeneous nucleation theory. Thus, our data suggests that molecular flat surfaces, rather than rough superhydrophobic surfaces, are beneficial for retarding ice formation under conditions that allow condensation and frost formation to occur.
|
|
| 8. |
- Heydari, Golrokh, et al.
(författare)
-
Wetting hysteresis induced by temperature changes : Supercooled water on hydrophobic surfaces
- 2016
-
Ingår i: Journal of Colloid and Interface Science. - : Academic Press. - 0021-9797 .- 1095-7103. ; 468, s. 21-33
-
Tidskriftsartikel (refereegranskat)abstract
- The state and stability of supercooled water on (super)hydrophobic surfaces is crucial for low temperature applications and it will affect anti-icing and de-icing properties. Surface characteristics such as topography and chemistry are expected to affect wetting hysteresis during temperature cycling experiments, and also the freezing delay of supercooled water. We utilized stochastically rough wood surfaces that were further modified to render them hydrophobic or superhydrophobic. Liquid flame spraying (LFS) was utilized to create a multi-scale roughness by depositing titanium dioxide nanoparticles. The coating was subsequently made non-polar by applying a thin plasma polymer layer. As flat reference samples modified silica surfaces with similar chemistries were utilized. With these substrates we test the hypothesis that superhydrophobic surfaces also should retard ice formation. Wetting hysteresis was evaluated using contact angle measurements during a freeze-thaw cycle from room temperature to freezing occurrence at -7 °C, and then back to room temperature. Further, the delay in freezing of supercooled water droplets was studied at temperatures of -4 °C and -7 °C. The hysteresis in contact angle observed during a cooling-heating cycle is found to be small on flat hydrophobic surfaces. However, significant changes in contact angles during a cooling-heating cycle are observed on the rough surfaces, with a higher contact angle observed on cooling compared to during the subsequent heating. Condensation and subsequent frost formation at sub-zero temperatures induce the hysteresis. The freezing delay data show that the flat surface is more efficient in enhancing the freezing delay than the rougher surfaces, which can be rationalized considering heterogeneous nucleation theory. Thus, our data suggests that molecular flat surfaces, rather than rough superhydrophobic surfaces, are beneficial for retarding ice formation under conditions that allow condensation and frost formation to occur.
|
|
| 9. |
- Saarimaa, Ville J., et al.
(författare)
-
Assessment of pitting corrosion in bare and passivated (wet scCO2-induced patination and chemical passivation) hot-dip galvanized steel samples with SVET, FTIR, and SEM (EDS)
- 2020
-
Ingår i: Materials and corrosion - Werkstoffe und Korrosion. - : Wiley-VCH Verlag. - 0947-5117 .- 1521-4176.
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, the local electrochemical activity of untreated and passivated (natural or chemical passivation) zinc specimens was observed during immersion in a 0.1-M NaCl solution. The localized anodic activity during the exposure, measured with the scanning vibrating electrode technique, was linked to zinc dissolution by the pitting corrosion mechanism. It was correlated to specific corrosion products characterized by Fourier transmission infrared (FTIR) microscopy. FTIR molecule maps were produced from individual pitting corrosion sites (100–200 µm in width). With argon ion beam milling and latest energy-dispersive X-ray spectroscopy (EDS) technology, element maps with a high spatial resolution (≪100 nm) were recorded from abrasion- and beam-sensitive corrosion products, showing a residual layer structure. This study demonstrates the capability of FTIR mapping, cross-section polishing, and state-of-the-art scanning electron microscopy imaging, and EDS element mapping to produce high-resolution elemental, molecular, and visual information about pitting corrosion mechanisms on a hot-dip galvanized steel sample.
|
|
| 10. |
- Wärnheim, Alexander, et al.
(författare)
-
Depth-Resolved FTIR-ATR Imaging Studies of Coating Degradation during Accelerated and Natural Weathering─Influence of Biobased Reactive Diluents in Polyester Melamine Coil Coating
- 2022
-
Ingår i: ACS Omega. - : American Chemical Society (ACS). - 2470-1343. ; 7:27, s. 23842-
-
Tidskriftsartikel (refereegranskat)abstract
- Improved methods to assess the degradation of coil coatings to approximate lifetime have been an area of academic and industrial interest for decades. This work aims to elucidate the differences in the degradation behavior of two coil coating systems: one standard commercial formulation and one formulation with a significant addition of biorenewable reactive diluents. Depth-resolved degradation behavior of samples exposed to accelerated and natural field weathering is assessed. Focal plane array attenuated total reflection-Fourier transform infrared spectroscopy was used to acquire high-resolution chemical data from a sloping cross section. The results agreed with conventional photoacoustic spectroscopy. Degradation profiles for the two coatings were significantly different, with the biobased samples showing a more durable behavior. This study provides a method for detailed assessment of coating degradation, giving a good estimation of its durability. This is both a way to compare the performance of coating systems and to improve the understanding of the impact of exposure conditions, paving the way for the development of more sustainable coil coatings.
|
|
