| 1. |
- Albinsson, Anton, 1989, et al.
(författare)
-
Required friction utilization for friction estimation on wet asphalt, an experimental study
- 2018
-
Ingår i: The Dynamics of Vehicles on Roads and Tracks. - : CRC Press/Balkema. - 9781138035713 ; 1, s. 407-412
-
Konferensbidrag (refereegranskat)abstract
- Real-time information about the friction coefficient between the tyre and the road can be used to improve active safety systems and is an enabler for autonomous vehicles. Large tyre force excitation is normally required to obtain an accurate friction estimate. This paper quantifies this requirement for four different tyre models on wet salted asphalt at water freezing temperatures. Cost functions and different tyre models are evaluated and the results are compared to a previous study performed for snow conditions. The suitability of commonly used tyre models for friction estimation on snow and wet asphalt has thus been investigated.
|
|
| 2. |
- Andersson, Anders, 1983-, et al.
(författare)
-
Co-simulation architecture with pedestrian, vehicle, and traffic simulators
- 2021
-
Ingår i: Actes (IFSTTAR). - : Driving Simulation Association. ; , s. 181-184
-
Konferensbidrag (refereegranskat)abstract
- Automated and connected traffic systems with cooperative functionality need effective testing. One way to enable such testing is to represent the current traffic environment by co-simulating different simulators using a communication layer between the simulators for cooperative functionality. With this approach, this paper presents a platform with its included simulators (vehicle, pedestrian, and traffic simulators), the used run-time infrastructure (RTI) for co-simulation, and the connection to the Unreal Engine based visual system for the simulators. The architecture was tested with two vehicle simulators (one autonomous bus and a truck), one pedestrian simulator, and one traffic simulator connected using a cloud-based service for the RTI.
|
|
| 3. |
- Andersson, Jan, et al.
(författare)
-
Traffic safety effects when overtaking 30 meter trucks
- 2012
-
Ingår i: Advances in Human Factors and Ergonomics 2012- 14 Volume Set. - : Taylor & Francis. - 146655262X - 9781466552623
-
Konferensbidrag (refereegranskat)abstract
- The purpose of this paper is to investigate if the introduction of extra-long and heavy trucks has an effect on traffic safety on Swedish roads, especially in relation to overtaking maneuvers. Traffic safety effects will be measured in terms of road user behavior concerning accelerations and time slots. First, focus group interviews with heavy truck drivers. Truck drivers that do not drive extra-long trucks believe that the introduction of extra-long trucks will create a number of traffic safety problems especially in terms of conflicts with ordinary road users. The drivers of extra-long trucks do not experience the problems that ordinary truck drivers predict. The problems they experience can be taken care of with more planning (thinking ahead). They also believe that the traffic sign on the back of the extra-long vehicle has a positive effect. The truck company, working environment and truck equipment are other important aspects mentioned by the drivers of the extra-long vehicles.The simulator study investigates overtaking situations on a 2+1-lane highway, with extra-long trucks (30.4 m) and ordinary trucks (18.75 m). The results reveal that the distance from the rear/front of the truck to the point where only one lane exists affects car drivers’ decision to overtake, independently of truck length. If the truck is in the relatively same position, the timeslot for a safe overtaking maneuver before next one-lane section was reduced significantly for extra-long trucks compared to ordinary trucks. The conclusion is that there exist small tendencies which point in the direction of enhanced traffic safety problems with the introduction of extra-long trucks. The results should, however, be interpreted with caution as the number of data points was few and collected in specific situations and in specific conditions. It was neither considered how the introduction of longer and heavier trucks, given a constant amount of goods, reduces the number of heavy trucks on the road network.
|
|
| 4. |
- Andersson, Jan, et al.
(författare)
-
Trafiksäkerhetspåverkan vid omkörning av 30-metersfordon
- 2011
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Trafikverket överväger att tillåta längre och tyngre fordon på vägarna förutsatt att de inte påverkar trafiksäkerheten negativt. Syftet med studien var att undersöka säkerhetseffekten av fordonslängd, speciellt med avseende på olycksrisken vid omkörningar. Intervjuade förare av en 30-meters timmerbil hade inte upplevt de farhågor som förare av normallånga lastbilar uttryckt i samband med trånga rondeller och korsningar, men de nämner betydelsen av stödjande åkeri, arbetsmiljö och fordonsutrustning. En simulatorstudie studerade bilförares omkörningar av ett 30- och ett 18,75-metersfordon på en 2+1-väg i situationen då två körfält går ihop till ett. Tidluckan till ett återstående körfält var i genomsnitt 0,2 s (sign.) kortare efter omkörningar av 30-metersfordonet i situationer då bakänden var i samma relativa position som för 18,75-metersfordonet vid början av omkörningen. En fältstudie analyserade videoinspelade omkörningar av en 30- och en 24-meters timmerbil på en 2+1-väg och en tvåfältig väg. Ingen signifikant skillnad i tidluckor kunde påvisas mellan omkörningar av de två fordonen för någon av vägtyperna. Det senare resultatet ska dock tolkas med försiktighet på grund av ojämnt distribuerad data som insamlats under specifika förhållanden. Slutsatserna är att det finns en liten tendens till negativ säkerhetseffekt vid omkörningar av längre fordon, och att fler fältstudier är nödvändiga.
|
|
| 5. |
- Andersson, Mats, et al.
(författare)
-
Road Friction Estimation
- 2007
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- This project is part of the Swedish IVSS program. The aim of IVSS is to stimulate research and development for the road safety of the future. Road conditions with low friction have been identified as a frequent cause of traffic accidents. Therefore, technology to automaticallydetect changes in road conditions and alert the driver or take proper actions with active driver support systems would be a key contribution to increased road safety.The aim of this project was to investigate the possibilities to estimate the tire to road friction.Three different approaches have been developed and evaluated, from concept to early prototypes in test vehicles. In the first method, the estimation of the coefficient of friction is based on the forces and torques that are produced at the front tires at cornering maneuvers.The second method is based on a physical model of the tire behavior and estimates road friction from information on the forces that are produced at straight driving. The third method is based on an optical sensor that classifies the road surface ahead of the vehicle.The three methods have been successfully evaluated in proving ground and public road tests in summer and winter conditions with different tires, and have been compared with reference measurements. The conclusion is that all three methods can be used for tire to road frictionestimation and are recommended for further development and industrialization.
|
|
| 6. |
- Bolling, Anne, et al.
(författare)
-
Improving the realism in the VTI driving simulators : Shake final report
- 2012
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Väg- och transportforskningsinstitutet (VTI) har tre avancerade körsimulatorer med rörelsesystem. Syftet med detta projekt var att utveckla och implementera nya modeller för grafik, vibrationer och buller, allt i syfte att öka realismen för föraren i simulatorn. Vidare skulle en valideringsstudie genomföras. Inom ramen för projektet uppnåddes följande:Utveckling av ett nytt grafiskt programpaket•Förbättring av modellerna för vibrationer på grund av däck/väg•Förbättring av rörelsesystemet genom förskjutning av rotationscentrum•Förbättring av modulen för buller, genom återskapande av däck- och vägbuller.•Synkronisering mellan vägytans grafiska presentation, buller och vibrationer .Modellernas validitet testades i VTI:s simulator III. Statistisk testning av skillnader mellan verklig bil och simulator indikerade absolut validitet för subjektiva bedömningar av vägytans jämnhet och tysthet och för det objektiva måttet hastighet, med undantag av områden där hastighetsgränsen ändrades. I dessa områden erhölls endast relativ validitet eftersom både accelerationer och retardationer var snabbare i simulatorn än i verklig bil. Relativ validitet indikerades också för det subjektiva måttet generell komfort. Resultaten från de olika valideringarna visar att förbättringarna har varit framgångsrika och föraren i simulatorn kan nu se, höra och känna ojämnheter i vägbanan exakt när hjulen träffar dessa. Fortfarande återstår dock många möjligheter till ytterligare förbättringar i simulatormodellerna.
|
|
| 7. |
- Bolling, Anne, et al.
(författare)
-
SHAKE - an approach for realistic simulation of rough roads in a moving base driving simulator
- 2010
-
Ingår i: Trends in driving simulation design and experiments. - Arcueil : Institut national de recherche sur les transports et leur securite, INRETS. - 9782857826859 ; , s. 135-143
-
Konferensbidrag (refereegranskat)abstract
- With today’s advanced measurement equipment for measuring roads, it is possible to measure road geometry at high precision within a large span of wavelengths. Detailed information about the roads longitudinal and lateral profile, including macro texture, would in theory be sufficient for a realistic reproduction of road induced vibration and noise in a driving simulator. Especially, it would be possible to create a direct connection between the visual information of the road condition and the ride experience, which would increase the level of realism in the simulation. VTI has during three years performed an internal project called SHAKE with the aim to develop and implement models in VTI driving simulator III that use measured road data for generating realistic vibrations and audible road noise connected to the visual impression presented on the projection screen. This has indeed resulted in an more realistic driving experience, and a validation study with test persons driving both in the simulator and in the field has been undertaken. The OpenDRIVE standard is used as a framework for describing the road properties (e.g. visual, vibrations and noise). For this purpose some augumentations to the OpenDRIVE standard had to be made. This paper describes the technical implementations in the driving simulator, along with results from test drives on the implemented road sections
|
|
| 8. |
- Bruzelius, Fredrik, 1974-, et al.
(författare)
-
The influence of tractor lengths on traffic safety and efficiency : a simulation study
- 2022
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Several different heavy vehicle combinations are allowed on the Swedish road network. A commonly seen combination is the tractor and semi-trailer combination with a maximum total length of 16.5 meters. The legal limitation on the total length of the combination has led to the use of a short tractor to make space for more goods on the trailer. There is a concern that the shortness of the tractors will have a negative consequence on traffic safety and the ability to negotiate uphills. The short wheelbase of the tractor and the weight imbalance between the tractor and the semitrailer could be an issue when braking and negotiating turns. This study was ordered by the Swedish Transport Agency to investigate the traffic safety aspects and hill-climbing problems of certain heavy vehicle combinations. The concerns raised should be investigated from a vehicle dynamical point of view for the vehicle combinations in question and compare them with other common vehicle combinations through a simulation study. A set of tractor and semitrailer combinations have been simulated in severe conditions and maneuvers to investigate the vehicle response and its dependencies with respect to the wheelbase of the tractor, coupling length, fifth wheel lubrication, and road surface conditions. Whenever meaningful, a comparison was made with a Nordic combination (truck and full trailer) as well as a B-double combination (tractor, link trailer, and trailer). The overall result of the simulation study is that the tractor and semitrailer combination is a stable combination, which outperforms the longer and heavier Nordic and B-double combinations in all the measured situations and maneuvers where comparison is meaningful. Furthermore, the wheelbase of the tractor seems to have a very minor effect on the performance of the vehicle combinations.
|
|
| 9. |
- Bruzelius, Fredrik, 1974-, et al.
(författare)
-
Towards an Indoor Winter Tire Classification Test
- 2012
-
Ingår i: Proceedings of VSDIA 2012.
-
Konferensbidrag (refereegranskat)abstract
- From a traffic safety perspective it is highly motivated to define winter tires interms of their performance in icy road conditions. The present definition of winter(snow) tires, introduced in the EU in 2012, is based on packed snow performance.The present paper investigates the feasibility of an indoor winter tire classificationtest on ice. Results presented here indicates that a test procedure in an indoorhockey rink is possible, with relatively high repeatability. However, further fieldtest is required to fully establish feasibility of the procedure.
|
|
| 10. |
- Bruzelius, Fredrik, 1974-, et al.
(författare)
-
Validation of a basic combined slip tyre model for use in friction estimation applications
- 2014
-
Ingår i: Proceedings of the Institution of mechanical engineers. Part D, journal of automobile engineering. - : SAGE Publications. - 0954-4070 .- 2041-2991. ; 228:13, s. 1622-1629
-
Tidskriftsartikel (refereegranskat)abstract
- Tyre modelling is an important part of understanding and estimating the tyre-road friction. In this paper a basic steady-state tyre model for the combined-slip case is derived. The model is intended to be used in friction estimations applications, where the model complexity is of high priority. The model, described using only two parameters, is validated with measured data from various conditions and tyre types using mobile measurement equipment. The performance from the measurements suggests that only two parameters are sufficient for the combined-slip case.
|
|
