| 1. |
- Das, Oisik, et al.
(författare)
-
An all-gluten biocomposite : Comparisons with carbon black and pine char composites
- 2019
-
Ingår i: Composites. Part A, Applied science and manufacturing. - : Elsevier. - 1359-835X .- 1878-5840. ; 120, s. 42-48
-
Tidskriftsartikel (refereegranskat)abstract
- Three different charcoals (gluten char, pine bark char and carbon black) were used to rectify certain property disadvantages of wheat gluten plastic. Pyrolysis process of gluten was investigated by analysing the compounds released at different stages. Nanoindentation tests revealed that the gluten char had the highest hardness (ca. 0.5 GPa) and modulus (7.8 GPa) followed by pine bark char and carbon black. The addition of chars to gluten enhanced the indenter-modulus significantly. Among all the charcoals, gluten char was found to impart the best mechanical and water resistant properties. The addition of only 6 wt% gluten char to the protein caused a substantial reduction in water uptake (by 38%) and increase of indenter-modulus (by 1525%). It was shown that it is possible to obtain protein biocomposites where both the filler and the matrix are naturally sourced from the same material, in this case, yielding an all-gluten derived biocomposite.
|
|
| 2. |
- Das, Oisik, et al.
(författare)
-
Naturally-occurring bromophenol to develop fire retardant gluten biopolymers
- 2020
-
Ingår i: Journal of Cleaner Production. - : Elsevier. - 0959-6526 .- 1879-1786. ; 243
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of the study was to impart fire retardancy in wheat gluten polymer through naturally-occurring additives such as lanosol. The fire properties of lanosol were compared with two other conventional brominated fire retardants (Tetrabromobisphenol A and Hexabromocyclododecane). Samples containing fire retardants and gluten were prepared through compression moulding process and then characterised for their fire and mechanical properties. All fire retardants enhanced the reaction-to-fire and thermal properties of gluten while generating V-0 (i.e. vertical position and self-extinguished) ratings in the UL-94 test. The presence of all the fire retardants increased the modulus of the gluten polymer but the fire retardant particles were detrimental for the tensile strength. Nevertheless, lanosol addition delayed ignition and lowered peak heat release rate of gluten by the maximum amount, thereby leading to relatively higher fire performance index (compared to the other fire retardants). Lanosol also allowed the gluten to create a dense char barrier layer during burning that impeded the transfer of heat and flammable volatiles. The fact that only 4 wt% lanosol was able to cause self-extinguishment under direct flame and reduce peak heat release rate by a significant 50% coupled with its inherent occurrence in nature, raises the question if lanosol can be a potential fire retardant in polymeric systems, although it is a bromophenol.
|
|
| 3. |
- Holder, Shima L., et al.
(författare)
-
Solubility and Diffusivity of Polar and Non-Polar Molecules in Polyethylene-Aluminum Oxide Nanocomposites for HVDC Applications
- 2020
-
Ingår i: Energies. - : MDPI AG. - 1996-1073. ; 13:3, s. 722-
-
Tidskriftsartikel (refereegranskat)abstract
- The best commercial high-voltage insulation material of today is (crosslinked) ultra-pure low-density polyethylene (LDPE). A 100-fold decrease in electrical conductivity can be achieved by adding 1–3 wt.% of well-dispersed inorganic nanoparticles to the LDPE. One hypothesis is that the nanoparticle surfaces attract ions and polar molecules, thereby cleaning the surrounding polymer, and thus reducing the conductivity. LDPE-based nanocomposites with 1–12 wt.% octyl-coated aluminum oxide nanoparticles were prepared and the sorption and desorption of one polar compound (acetophenone, a crosslinking by-product) and one non-polar compound of a similar size (limonene) were examined. Since the uptake of acetophenone increased linearly with increasing filler content, whereas the uptake of limonene decreased, the surface attraction hypothesis was strengthened. The analytical functions for predicting composite solubility as a function of particle size and filler fraction were derived using experimental solubility measurements and Monte Carlo simulations.
|
|
| 4. |
- Holder, Shima, et al.
(författare)
-
Understanding and modelling the diffusion process of low molecular weight substances in polyethylene pipes
- 2019
-
Ingår i: Water Research. - : Elsevier Ltd. - 0043-1354 .- 1879-2448. ; , s. 301-309
-
Tidskriftsartikel (refereegranskat)abstract
- Peroxides are widely used as crosslinkers in polyethylene (PE) drinking water pipes. Cross-linked polyethylene (PEX) has better mechanical properties than PE, but peroxide decomposition by-products can migrate from PEX water pipes into the drinking water unless sufficient preventive actions are undertaken. This work systematically examines the migration of tert-Butyl methyl ether (MTBE), a dominating crosslinking by-product from PEX water pipes, into tap water by utilizing both experimental techniques and finite element (FEM) diffusion modeling. The effects of pipe geometry, tap water temperature (23–80 °C), boundary conditions (air or water interface) and degasing (at 180 °C) were considered. The MTBE diffusivity increased strongly with increasing temperature and it was concluded that a desired water quality can be achieved with proper degasing of the PEX pipes. As the FEM simulations were in excellent agreement with the experimental results, the model can accurately predict the MTBE concentration as a function of time, water temperature and PEX pipe geometry, and enable the pipe manufacturers to aid in ensuring desirable drinking water quality.
|
|
| 5. |
- Lee, Ching-Hwa, et al.
(författare)
-
A study on development of alternative biopolymers based proton exchange membrane for microbial fuel cells and effect of blending ratio and ionic crosslinking on bioenergy generation and COD removal
- 2019
-
Ingår i: Journal of polymer research. - : Springer. - 1022-9760 .- 1572-8935. ; 26:12
-
Tidskriftsartikel (refereegranskat)abstract
- The use of biopolymers as alternative proton exchange membranes (PEMs) is receiving significant attention in microbial fuel cells (MFCs) due to their attractive and competitive physico-chemical properties, eco-friendly behavior and biodegradable nature. In this study we developed the biopolymer-based blend PEMs using chitosan (Cs) alginate (Alg) for bioelectricity production and simultaneous wastewater treatment and also investigated the effect of blending ratio of the membrane and ionic crosslinking between the two biopolymers on MFC performance. The membranes of Cs:Alg were fabricated in volume ratio of 100:0, 80:20, 60:40, 50:50, 40:60, 20:80, and 0:100 via a solution casting and solvent evaporation method followed by crosslinking with phosphoric acid to avoid excess swelling of the hydrophilic polymers and increase the mechanical strength. Among these, the 50:50 ratio membranes exhibited the highest power generation (115 mW/m(2)) with 1340% water uptake, however the membrane with 40:60 ratio displayed maximum COD removal (78.6%) compared to other membranes. The structure and surface morphology of obtained membranes were examined using Infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy-dispersive X-ray spectroscopy (EDX), Sorption and cation exchange capacity, and tensile strength. Sorption, cation exchange capacity and mechanical properties of Cs membranes increased with the addition of Alg with near to stoichiometric ratio.
|
|
