| 1. |
|
|
| 2. |
- Chang, Tsu Chi, et al.
(författare)
-
Electrically Injected GaN-Based Vertical-Cavity Surface-Emitting Lasers with TiO2 High-Index-Contrast Grating Reflectors
- 2020
-
Ingår i: ACS Photonics. - : American Chemical Society (ACS). - 2330-4022. ; 7:4, s. 861-866
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate the first electrically injected GaN-based vertical-cavity surface-emitting lasers (VCSELs) with a TiO2 high-index-contrast grating (HCG) as the top mirror. Replacing the top distributed Bragg reflector (DBR) with an HCG offers substantial thickness reduction, polarization-pinning, and setting of the resonance wavelength by the grating parameters. Conventional HCGs are usually suspended in the low refractive index material, such as air, in order to create the largest refractive index contrast. However, the mechanical stability of such structures can be questioned and creating free-hanging GaN-membrane on top of GaN is problematic. We have therefore fabricated TiO2-HCGs resting directly on GaN without an air-gap. No DBR layers are used below the HCG to boost the reflectivity. A VCSEL with an aperture diameter of 10 μm shows a threshold current of 25 mA under pulsed operation at room temperature. The lasing modes locate around 400 nm and are transversely electrically -polarized with a line width of 0.5 nm. The full-width half-maximum beam divergence is 10°. This demonstration of a TiO2-HCG VCSEL offers a new route to achieve polarization pinning and could also allow additional benefits such as postgrowth setting of the resonance wavelength.
|
|
| 3. |
- Hong, Kuo Bin, et al.
(författare)
-
Monolithic high-index contrast grating mirror for a GaN-based vertical-cavity surface-emitting laser
- 2021
-
Ingår i: Photonics Research. - 2327-9125. ; 9:11, s. 2214-2221
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, a pulsed electrically pumped GaN-based vertical-cavity surface-emitting laser (VCSEL) with one dielectric distributed Bragg reflector and one n-GaN monolithic high-index contrast grating (MHCG) mirror was demonstrated at room temperature. The reflectance of the n-GaN MHCG and cavity mode behaviors of the VCSEL with MHCG for varying n-GaN thickness, MHCG pattern diameter, and current aperture size were numerically investigated. Measured characteristics of the fabricated device showed that the lasing action started at an injection current of 10.2 mA, corresponding to a current density of about 15.1 kA=cm2. Above threshold, the measured slope efficiency was 6.2 × 10−3 W∕A, and the output power was 0.13 mW at 30 mA. Moreover, the measured lasing peak occurring at 403.4 nm and the longitudinal mode spacing of 5.6 nm were in good agreement with simulations. The incorporation of an n-GaN MHCG mirror not only greatly simplified the fabrication but also substantially improved the lasing characteristics in comparison to the previous work applying TiO2 HCG mirrors.
|
|
| 4. |
- Huang, Shen-Che, et al.
(författare)
-
Two-dimensional designed fabrication of subwavelength grating HCG mirror on Silicon-on-insulator
- 2016
-
Ingår i: HIGH CONTRAST METASTRUCTURES V. - : SPIE - International Society for Optical Engineering. - 9781628419924
-
Konferensbidrag (refereegranskat)abstract
- We designed and fabricated a two dimensional high contrast subwavelength grating (HCG) mirrors. The computer-aided software was employed to verify the structural parameters including grating periods and filling factors. From the optimized simulation results, the designed HCG structure has a wide reflection stopband (reflectivity (R) >90%) of over 200 nm, which centered at telecommunication wavelength. The optimized HCG mirrors were fabricated by electron-beam lithography and inductively coupled plasma process technique. The experimental result was almost consistent with calculated data. This achievement should have an impact on numerous photonic devices helpful attribution to the integrated HCG VCSELs in the future.
|
|
