| 1. |
- Jiang, Xiao, et al.
(author)
-
Highly Efficient Solid-State Dye-Sensitized Solar Cells Based on Triphenylamine Dyes
- 2011
-
In: Advanced Functional Materials. - : Wiley. - 1616-301X .- 1616-3028. ; 21:15, s. 2944-2952
-
Journal article (peer-reviewed)abstract
- Two triphenylamine-based metal-free organic sensitizers, D35 with a single anchor group and M14 with two anchor groups, have been applied in dye-sensitized solar cells (DSCs) with a solid hole transporting material or liquid iodide/triiodide based electrolyte. Using the molecular hole conductor 2,2',7,7'-tetrakis-(N,N-di-p-methoxyphenyl-amine)9,9'-spirobifluorene (spiro-OMeTAD), good overall conversion efficiencies of 4.5% for D35 and 4.4% for M14 were obtained under standard AM 1.5G illumination (100 mW cm(-2)). Although M14 has a higher molar extinction coefficient (by similar to 60%) and a slightly broader absorption spectrum compared to D35, the latter performs slightly better due to longer lifetime of electrons in the TiO(2), which can be attributed to differences in the molecular structure. In iodide/triiodide electrolyte-based DSCs, D35 outperforms M14 to a much greater extent, due to a very large increase in electron lifetime. This can be explained by both the greater blocking capability of the D35 monolayer and the smaller degree of interaction of triiodide (iodine) with D35 compared to M14. The present work gives some insight into how the molecular structure of sensitizer affects the performance in solid-state and iodide/triiodide-based DSCs.
|
|
| 2. |
- Yang, Lei, et al.
(author)
-
Comparing spiro-OMeTAD and P3HT hole conductors in efficient solid state dye-sensitized solar cells
- 2012
-
In: Physical Chemistry, Chemical Physics - PCCP. - : Royal Society of Chemistry (RSC). - 1463-9076 .- 1463-9084. ; 14:2, s. 779-789
-
Journal article (peer-reviewed)abstract
- Two hole conductor materials, spiro-OMeTAD and P3HT, were compared in solid-state dye-sensitized solar cells. Two organic dyes containing one anchor unit (D35) or two anchor units (M3) were used in the comparison. Absorbed photon to current conversion efficiency close to unity was obtained for the devices with spiro-OMeTAD. Energy conversion efficiencies of 4.7% and 4.9% were measured for the devices with spiro-OMeTAD and the dyes D35 and M3, respectively. For the devices using the P3HT hole conductor the results were rather different comparing the two dye molecules, with energy conversion efficiencies of 3.2% and 0.5% for D35 and M3, respectively. Photo-induced absorption measurements suggest that the regeneration of the dyes, and the polymer infiltration, is not complete using P3HT, while spiro-OMeTAD regenerates the dyes efficiently. However, the TiO(2)/D35/P3HT system shows rather high energy conversion efficiency and electrochemical oxidation of the dyes on TiO(2) indicates that D35 have a more efficient dye to dye hole conduction than M3, which thereby might explain the higher performance. The dye hole conduction may therefore be of significant importance for optimizing the energy conversion in such hybrid TiO(2)/dye/polymer systems.
|
|
| 3. |
- Abdelhamid, Hani Nasser, et al.
(author)
-
Towards implementing hierarchical porous zeolitic imidazolate frameworks in dye-sensitized solar cells
- 2019
-
In: Royal Society Open Science. - : Royal Society Publishing. - 2054-5703. ; 6:7
-
Journal article (peer-reviewed)abstract
- A one-pot method for encapsulation of dye, which can be applied for dye-sensitized solar cells (DSSCs), and synthesis of hierarchical porous zeolitic imidazolate frameworks (ZIF-8), is reported. The size of the encapsulated dye tunes the mesoporosity and surface area of ZIF-8. The mesopore size, Langmuir surface area and pore volume are 15 nm, 960-1500 m(2). g(-1) and 0.36-0.61 cm(3). g(-1), respectively. After encapsulation into ZIF-8, the dyes show longer emission lifetimes (greater than 4-8-fold) as compared to the corresponding non-encapsulated dyes, due to suppression of aggregation, and torsional motions.
|
|
| 4. |
- El-Zohry, Ahmed, et al.
(author)
-
Gigantic Relevance of Twisted Intramolecular Charge Transfer for Organic Dyes Used in Solar Cells
- 2018
-
In: The Journal of Physical Chemistry C. - : American Chemical Society (ACS). - 1932-7447 .- 1932-7455. ; 122:42, s. 23998-24003
-
Journal article (peer-reviewed)abstract
- Within this work, we emphasis on the importance of twisted intramolecular charge transfer (TICT) process in organic dyes based on triphenyl amine moiety to achieve high performance in dye-sensitized solar cells. Through the comparison between two recent made dyes, Ll and L1Fc, on different semiconductors (TiO2, and ZrO2), we could spectrally and dynamically detect for the first time the formation of TICT state for Ll on ZrO2 after localized charge transfer (LCT) state population, and an electron injection process from TICT state on TiO2. However, for the excited L1Fc dye, the ultrafast electron transfer from ferrocene (Fc) moiety to the Ll unit quenched the formation of TICT state in L1Fc on semiconductors, leading instead to an electron injection process from the LCT state. The electron injection from TICT state in Ll associated with structural rearrangements on TiO2 leads to slow recombination process and an efficiency improvement of about 325%, compared to solar cells based on L1Fc dye, in which TICT state formation is hindered. Similar electron dynamics are obtained for Ll on TiO2 upon physically hindering the TICT process by adding polymer matrix. The presence of TICT state for Ll dye and similar triphenyl amine dyes aids to reconstruct the kinetic profile for these dyes on semiconductor surfaces, and to redesign organic dyes accordingly for higher efficiency in solar cells.
|
|
| 5. |
- El-Zohry, Ahmed M., et al.
(author)
-
Twisted Intramolecular Charge Transfer (TICT) Controlled by Dimerization : An Overlooked Piece of the TICT Puzzle
- 2021
-
In: Journal of Physical Chemistry A. - : American Chemical Society (ACS). - 1089-5639 .- 1520-5215. ; 125:14, s. 2885-2894
-
Journal article (peer-reviewed)abstract
- Organic dyes have shown high efficiencies in solar cells, which is mainly attributed to the push-pull strategy present in such dyes upon attaching to the semiconductor surfaces. We deeply studied the fundamental photophysical properties of cyanoacrylic dyes, mostly the L1 dye, and found unique emission properties that depend on many factors such as the solvent polarity and the concentration of the dye and could present a complete emission picture about this family of dyes. The L1 dye shows an intramolecular charge transfer (ICT) emission state at low concentrations (approximately nanomolar scale) and shows a twisted intramolecular charge transfer (TICT) emission state in specific solvents upon increasing the concentration to the micromolar scale. Moreover, the associated emission lifetimes of the ICT and TICT states of the L1 dye depend on solvent basicity, highlighting the role of hydrogen bond formation on controlling such states. Density functional theory calculations are performed to gain insight into the photophysical properties of the dye and revealed that H-bonding between the carboxylic groups triggers the dimerization at low concentrations. Using femtosecond transient absorption, we assigned the rate of TICT formation to be in the range (160-650 fs)(-1), depending on the size of the studied cyanoacrylic dye. Therefore, we add herein a new dimension for controlling the formation of the TICT state, in addition to the solvent polarity and acceptor strength parameters. These findings are not limited to the studied dyes, and we expect that numerous organic carboxylic acids dyes show similar properties.
|
|
| 6. |
|
|
| 7. |
- Hao, Yan, et al.
(author)
-
Efficient Dye-Sensitized Solar Cells with Voltages Exceeding 1 V through Exploring Tris(4-alkoxyphenyl)amine Mediators in Combination with the Tris(bipyridine) Cobalt Redox System
- 2018
-
In: ACS Energy Letters. - : American Chemical Society (ACS). - 2380-8195. ; 3:8, s. 1929-1937
-
Journal article (peer-reviewed)abstract
- Tandem redox electrolytes, prepared by the addition of a tris(p-anisyl)amine mediator into classic tris(bipyridine)cobalt-based electrolytes, demonstrate favorable electron transfer and reduced energy loss in dye-sensitized solar cells. Here, we have successfully explored three tris(4-alkoxyphenyl)-amine mediators with bulky molecular structures and generated more effective tandem redox systems. This series of tandem redox electrolytes rendered solar cells with very high photovoltages exceeding 1 V, which approaches the theoretical voltage limit of tris(bipyridine)cobalt-based electrolytes. Solar cells with power conversion efficiencies of 9.7-11.0% under 1 sun illumination were manufactured. This corresponds to an efficiency improvement of up to 50% as compared to solar cells based on pure tris(bipyridine)cobalt-based electrolytes. The photovoltage increases with increasing steric effects of the tris(4-alkoxyphenyl)amine mediators, which is attributed to a retarded recombination kinetics. These results highlight the importance of structural design for optimized charge transfer at the sensitized semiconductor/electrolyte interface and provide insights for the future development of efficient dye-sensitized solar cells.
|
|
| 8. |
- Karlsson, Karl Martin, 1981-
(author)
-
Design, Synthesis and Properties of Organic Sensitizers for Dye Sensitized Solar Cells
- 2011
-
Doctoral thesis (other academic/artistic)abstract
- This thesis gives a detailed description of the design and synthesis of new organic sensitizers for Dye sensitized Solar Cells (DSCs). It is divided in 7 chapters, where the first gives an introduction to the field of DSCs and the synthesis of organic sensitizers. Chapters 2 to 6 deal with the work of the author, starting with the first publication and the other following in chronological order. The thesis is completed with some concluding remarks (chapter 7). The DSC is a fairly new solar cell concept, also known as the Grätzel cell, after its inventor Michael Grätzel. It uses a dye (sensitizer) to capture the incident light. The dye is chemically connected to a porous layer of a wide band-gap semiconductor. The separation of light absorption and charge separation is different from the conventional Si-based solar cells. Therefore, it does not require the very high purity materials necessary for the Si-solar cells. This opens up the possibility of easier manufacturing for future large scale production. Since the groundbreaking work reported in 1991, the interest within the field has grown rapidly. Large companies have taken up their own research and new companies have started with their focus on the DSC. So far the highest solar energy to electricity conversion efficiencies have reached ~12%. The sensitizers in this thesis are based on triphenylamine or phenoxazine as the electron donating part in the molecule. A conjugated linker allows the electrons to flow from the donor to the acceptor, which will enable the electrons to inject into the semiconductor once they are excited. Changing the structure by introducing substituents, extending the conjugation and exchanging parts of the molecule, will influence the performance of the solar cell. By analyzing the performance, one can evaluate the importance of each component in the structure and thereby gain more insight into the complex nature of the dye sensitized solar cell.
|
|
| 9. |
- Liu, Peng, et al.
(author)
-
Molecular Engineering of D-pi-A Type of Blue-Colored Dyes for Highly Efficient Solid-State Dye-Sensitized Solar Cells through Co-Sensitization
- 2018
-
In: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 10:42, s. 35946-35952
-
Journal article (peer-reviewed)abstract
- A novel blue-colored organic donor-pi-acceptor sensitizer, the so-called MKA16 dye, has been employed to construct solid-state dye-sensitized solar cells (ssDSSCs). Using 2,2',7-,7'-tetrakis(N,N-di-p-methoxyphenyl-amine) 9,9'-spirobifuorene (Spiro-OMeTAD) as hole-transport material, a good conversion efficiency of 5.8% was recorded for cells based on the MKA16 dye and a high photovoltage of 840 mV in comparison with 5.6% efficiency using the known (Dyenamo Blue) dye. By co-sensitization using the orange-colored D35 dye and MKA16 together, the solid-state solar cells showed an excellent efficiency of 7.5%, with a high photocurrent of 12.41 mA cm(-2) and open-circuit voltage of 850 mV. The results show that the photocurrent of ssDSSCs can be significantly improved by co-sensitization mainly attributed to the wider light absorption range contributing to the photocurrent. In addition, results from photo-induced absorption spectroscopy show that the dye regeneration is efficient in co-sensitized solar cells. The current results possible routes of improving the design of aesthetic and highly efficient ssDSSCs.
|
|
| 10. |
- Liu, Peng, et al.
(author)
-
The combination of a new organic D-pi-A dye with different organic hole-transport materials for efficient solid-state dye-sensitized solar cells
- 2015
-
In: Journal of Materials Chemistry A. - : RSC Publishing. - 2050-7488 .- 2050-7496. ; 3:8, s. 4420-4427
-
Journal article (peer-reviewed)abstract
- A new organic donor-pi-acceptor sensitizer MKA253 has been applied for highly efficient solid-state dye-sensitized solar cells (ssDSSCs). Using 2,2',7,7'-tetrakis(N,N-di-pi-methoxyphenyl-amine) 9,9'-spirobifluorene (Spiro-OMeTAD) as the hole transport material (HTM), an excellent power conversion efficiency of 6.1% was recorded together with a high short-circuit current of 12.4 mA cm(-2) under standard AM 1.5G illumination (100 mW cm(-2)). Different combinations of dyes and HTMs have also been investigated in the ssDSSC device. The results showed that small molecule HTM based devices suffer from comparably high electron recombination losses, thus causing low open-circuit voltage. In addition, photo-induced absorption (PIA) spectroscopy showed that the small-molecule HTMs lead to more efficient dye regeneration in comparison with Spiro-OMeTAD, despite a lower thermodynamic driving force. The results of this study also show that optimized energy levels for the dye-HTMs could be a vital factor for highly efficient ssDSSCs.
|
|
