| 1. |
- Saito, T. R., et al.
(författare)
-
Studies of three-and four-body hypernuclei with heavy-ion beams, nuclear emulsions and machine learning
- 2023
-
Ingår i: Journal of Physics, Conference Series. - : Institute of Physics (IOP). - 1742-6588 .- 1742-6596. ; 2586
-
Tidskriftsartikel (refereegranskat)abstract
- Interests on few-body hypernuclei have been increased by recent results of experiments employing relativistic heavy ion beams. Some of the experiments have revealed that the lifetime of the lightest hypernucleus, hypertriton, is significantly shorter than 263 ps which is expected by considering the hypertriton to be a weakly-bound system. The STAR collaboration has also measured the hypertriton binding energy, and the deduced value is contradicting to its formerly known small binding energy. These measurements have indicated that the fundamental physics quantities of the hypertriton such as its lifetime and binding energy have not been understood, therefore, they have to be measured very precisely. Furthermore, an unprecedented Lambda nn bound state observed by the HypHI collaboration has to be studied in order to draw a conclusion whether or not such a bound state exists. These three-body hypernuclear states are studied by the heavy-ion beam data in the WASA-FRS experiment and by analysing J-PARC E07 nuclear emulsion data with machine learning.
|
|
| 2. |
- Saito, T. R., et al.
(författare)
-
The WASA-FRS project at GSI and its perspective
- 2023
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section B. - : Elsevier. - 0168-583X .- 1872-9584. ; 542, s. 22-25
-
Tidskriftsartikel (refereegranskat)abstract
- A novel technique to study bound states of exotic hadrons in subatomic nuclei, such as hypernuclei and mesic nuclei, has been developed by employing the Fragment Separator FRS and the WASA central detector at GSI. Two experiments, S447 for studying light hypernuclei, especially hypertriton and a Ann bound state, and S490 for searching for ri' mesic-nuclei, were recently performed. Data analyses are currently in progress, and light charged particles such as protons and x & PLUSMN; are clearly observed and identified in the both experiments. For S447, light nuclear fragments that can also be residual nuclei from decays of hypernuclei of interests have been analysed by the FRS, and a momentum resolution, Ap/p, of 5 x 10-4 has been achieved. Further data analyses are to be completed. The WASA-FRS project will be continued and extended with the FRS at FAIR Phase 0, and upgrading of the WASA magnet and detectors is currently in progress. Furthermore, construction of a larger detector system with the Super-FRS at FAIR Phase 1 is also under consideration.
|
|
| 3. |
- Tanaka, Y. K., et al.
(författare)
-
WASA-FRS EXPERIMENTS IN FAIR PHASE-0 AT GSI
- 2023
-
Ingår i: ACTA PHYSICA POLONICA B PROCEEDINGS SUPPLEMENT. - : Jagiellonian University.
-
Konferensbidrag (refereegranskat)abstract
- We have developed a new and unique experimental setup integrating the central part of the Wide Angle Shower Apparatus (WASA) into the Fragment Separator (FRS) at GSI. This combination opens up possibilities of new experiments with high-resolution spectroscopy at forward 0 and measurements of light decay particles with nearly full solid-angle acceptance in coincidence. The first series of the WASA-FRS experiments have been successfully carried out in 2022. The developed experimental setup and two physics experiments performed in 2022 including the status of the preliminary data analysis are introduced.
|
|
| 4. |
- Polettini, M., et al.
(författare)
-
Decay studies in the A∼225 Po-Fr region from the DESPEC campaign at GSI in 2021
- 2022
-
Ingår i: Il Nuovo Cimento. - : Società Italiana di Fisica. - 2037-4909. ; 45:5
-
Tidskriftsartikel (refereegranskat)abstract
- The HISPEC-DESPEC collaboration aims at investigating the structure of exotic nuclei formed in fragmentation reactions with decay spectroscopy measurements, as part of the FAIR Phase-0 campaign at GSI. This paper reports on first results of an experiment performed in spring 2021, with a focus on beta-decaystudies in the Po-Fr nuclei in the 220 < A <230 island of octupole deformation exploiting the DESPEC setup. Ion-beta correlations and fast-timing techniques are being employed, giving an insight into this difficult-to-reach region.
|
|
| 5. |
- Kazantseva, N., et al.
(författare)
-
Martensitic transformations in Ti-6Al-4V (ELI) alloy manufactured by 3D Printing
- 2018
-
Ingår i: Materials Characterization. - : Elsevier BV. - 1044-5803 .- 1873-4189. ; 146, s. 101-112
-
Tidskriftsartikel (refereegranskat)abstract
- In the present investigation, Ti-6Al-4V ELI samples were manufactured by the powder-bed fusion (PBF) process using the laser sintering (LS) technology. Microstructure, chemical and phase constitution, and mechanical properties were studied by means of the transmission electron microscopy, atom probe tomography, X-ray diffraction, nanoindentation and mechanical testing. It was found that the structure of LS samples consisted of two different variants of metastable phases, namely the hexagonal α′ martensitic phase and small amounts of the orthorhombic α″ martensitic phase. The martensitic α′-phase was formed because of the high cooling rates of the LS method. The {101¯2} ⟨1¯011⟩ hexagonal martensite tensile twins were observed in the microstructure of the as-build alloy. Small areas with inner twinning martensitic plates, which are typical for the metastable orthorhombic martensitic phase in titanium alloys, were identified by the transmission electron microscopy. Atom probe tomography (APT) confirmed localization of β-stabilizing elements at interfaces, presumably at the twin or lamella boundaries. The structure and origin of the martensitic phases in 3D printed Ti-6Al-4V alloys are discussed with respect to in-situ heat treatment during manufacturing.
|
|
| 6. |
|
|
| 7. |
- Kazantseva, Natalia, et al.
(författare)
-
Oxygen and nitrogen concentrations in the Ti-6Al-4V Alloy manufactured by direct metal laser sintering (dmls) process
- 2017
-
Ingår i: Materials letters (General ed.). - : Elsevier. - 0167-577X .- 1873-4979. ; 209, s. 311-314
-
Tidskriftsartikel (refereegranskat)abstract
- Two machines from two scientific centers (Russia and South Africa) were used for the manufacturing of the Ti6Al4V alloys by the direct metal laser sintering. The chemical composition of powders complies with the ASTM F-136 (grade 5), ASTM B348 (grade 23) standard for medical applications. Analysis of the oxygen and nitrogen contamination in DMLS alloys was done with Van de Graaff accelerator with two Mega Volts. It is found that structures of the samples manufactured with two different machines used the same regimes are close to each other. TEM studies found the metastable martensitic structure and silicon nitride Si3N4. It was found that the oxygen and nitrogen contents in both samples are within the normal range for medical grade titanium alloys.
|
|
| 8. |
- Kazantseva, N. V., et al.
(författare)
-
Laser Additive 3D Printing of Titanium Alloys : Current Status, Problems, Trends
- 2021
-
Ingår i: Physics of metals and metallography. - : Maik Nauka/Interperiodica. - 0031-918X .- 1555-6190. ; 122:1, s. 6-25
-
Tidskriftsartikel (refereegranskat)abstract
- Features of 3D printing, including laser melting of metal powders, were considered in this work. The effect of laser operation mode on the structure, residual stresses, and properties of manufactured metals was reviewed. A method for choosing process parameters using single tracks as universal for all types of metal laser 3D printers was proposed. Structural characteristics and medical requirements for biocompatible materials were presented. The biocompatible Ti-6Al-4V alloy manufactured by selective laser melting was considered.
|
|
| 9. |
|
|
| 10. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Influence of heat treatment under hot isostatic pressing (HIP) on microstructure of intermetallic-reinforced tool steel manufactured by laser powder bed fusion
- 2020
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 772
-
Tidskriftsartikel (refereegranskat)abstract
- Microstructure and properties of as-built laser powder bed fusion (LPBF) steels differ from the conventional ones, and they may contain some porosity and lack of fusion. Therefore, post-treatments, including hot isostatic pressing (HIP), are used to density the material, and tailor the properties of the final product. Usually, HIP is performed as an operation separate from heat treatment. In the present investigation a new approach was used, in which the whole cycle of the heat treatment was carried out in HIP under pressure, and the influence of HIP on microstructure of an advanced stainless maraging tool steel manufactured by LPBF was investigated. For a comparison, a conventional steel grade of the same chemical composition, after a heat treatment at the same temperature-time conditions, was also characterized. The microstructure of the steel was investigated by means of advanced microscopy and atom probe tomography. The influence of the manufacturing route, heat treatment and HIP on microstructure, austenitic phase fraction and size distribution of precipitates was investigated, and the role of high pressure in stabilization of austenite in the microstructure was discussed. It was concluded that since HIP influences phase transformations, a fundamental understanding of the influence of HIP on microstructure is nececcary, and development of new post processing regimes guaranteeing the best performance of the material is required.
|
|
